Haryana Urban Development Authority Tender

[23.22.5.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.2. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Single Pole [Through Rate]

[23.24.3.2]MS STAND, BUS BAR CHAMBER AND PANELS 3.2. Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S. sheet and fixing with rag bolts on wall or on existing pedestal/angle iron frame including bonding, detachable top and bottom including painting and necessary connection etc. (Aluminium bars). 100 amp 4 bars of 55 cm each (cross section 25 mm x6 mm) chamber over all size 60 cm x 45 cm x 18cm [Through Rate]

[23.27.2]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 2. M.S. pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0 [Through Rate]

[23.27.3]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 3. M.S. pedestal of size 750 mm wide , 1200 mm high ,300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0 [Through Rate]

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate]

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate]

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.2.8.4]LT CABLE 8.4. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 16 sqmm [Through Rate]

[24.4.15.1]STREET LIGHT 15.1. B.S.E.N. 10025 High Masts "Supply, installation, testing and commissioning of 12.5 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer -in-Charge Thickness of Top and Bottom Section = 3 mm (minimum) Top Dia = 150 mm and Bottom Dia = 360mm Thickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum)" [Through Rate]

[24.4.8.7]STREET LIGHT 8.7. Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 9 Metre Long pole with top dia 100 mm and bottom 200 mm with base plate of size 350 x 350 x 20 mm. [Through Rate]

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate]

[24.9.1]RCC FOUNDATIONS FOR HIGH MAST OCTAGONAL POLES 1. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 75 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for high mast octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 12.5 m high mast pole [Through Rate]

Supply and erection of Prodigy type in-built L.T. C.T. meter of (40- 200 amps), 3-phase 415 Volts rating suitable for 3-phase, 4-wire system of make Secure, Genus or other make approved by the UHBVNL. The meter is to be fixed in M.S Sheet cubical meter box on existing PCC Pole. This includes all petty material i.e. M-Seal, Nut–Bolts, thimbles etc. Meter will be got tested from the UHBVNL lab by the contractor after depositing the meter testing fee by him and it will be refunded on production of receipt received from UHBVNL. (Excluding GST)

Supply, erection, testing and commissioning of ELEX-TWS-2EXT / Amson’s/LandT make Automatic electric timer to switch ON/OFF the street light automatically. It should have adjustable lux level switch, with extensible mountable sensor. It shall change ON/OFF timing automatically as per lux level of the Sun at sun-rising and sun setting, throughout the year. Shall have two Nos. LandT make, 3 pole power contactor model MNX-70 to control 70 amp per phase with 220 Volt coils. It shall have auto/manual switch for repair of street light during day time. The whole unit components to be assembled on Bakelite sheet with 16 amp capacity MCB to save the time switch. The erection of the complete unit in the existing pedestal with complete wiring upto the entire satisfaction of the Engineer-in-charge. ON/OFF Timer (Excluding GST)

Supply and erection of 63 Amps connection plate for incoming and outgoing cable in existing Panel/High Mast/Octagonal Pole etc. to be fitted with connector fixed on Bakelite sheet complete with nut and bolts. (Excluding GST)

Supply and erection of RCC foundation (of size 1.0 x 1.0 x 2 M) for erection of 12 Mtr. long octagonal pole including cost of 4 Nos. sets of G.I. foundation Nuts-bolts having G.I. of 85 microme and of size 750mmx24mm thickness, top end threaded upto 150 mm length with M.S. sheet of size 320x320x6 mm at bottom. Cement Concrete 1:1½:3 with stone aggregate 20mm nominal size. Reinforcement with 8 Nos., 12 mm dia steel bars vertically and 10 Nos. rings of size 8 mm dia steel bars. The foundation should have provision of PVC pipe for incoming and outgoing underground cable, complete in all respect upto entire satisfaction of Engineer-in-charge and as per drawing. (Without GST)

Erection of 12 Mtr. Long Octagonal pole on existing foundation including fixing of single arm bracket (2 Mtr. long ) on the top complete the rates are inclusive for petty material required and transportation of poles from store to site with loading and unloading . All the work will be executed as entire satisfaction of Engineer-in-charge of the work. (Excluding GST)

Supply and Erection of Octagonal pole door cover on existing 12 Mtr. long octagonal pole of size 50cm x 18cm x 14 SWG including nut-bolt complete in all respect up to the entire satisfaction of Engineer-in-charge of the work. (Excluding GST)

Supply and erection of Double Arm over-hang galvanized iron pipe bracket having canopy of B-class G.I. pipe, 0.60m long,125mm dia. Each arm the bracket to be of length 1500mm, made out of 50mm dia, B-class G.I. pipe, including 150mm long nipple for LED street light fitting if required, making an angle of 15 degree with horizontal plane including nut-bolts and all other petty material, labour charges etc. complete in all respect upto the entire satisfaction of Engineer-in-Charge. (WITH-OUT GST)

Supply and erection of PVC insulated and sheathed underground cable, loose in existing pipe or trenches 1100 volts core having solid aluminium conductor wires confirming to IS: 694:2010, including making necessary connections complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. Cable Size: 16 Sqmm x 4-core (Armd.). Make: Grandlay/Polycab/Havell`s. (Without GST)

Supply and erection of 120 watt LED Flood Light luminaire with multiple highly efficient and high power LED light with individual lens, pressure die cast aluminum housing with heat sink and aluminum extrusion, with secondary optics and enclosed with toughened glass, IP-66 level, having 120 lumens/watt, with 3 years defect liability period (on site replacement) free of cost, complete in all respect up to the entire satisfaction of Engineer-in-charge of the work. Make:- Philips/Bajaj/LT/Panasonic/Anchor - (Rate without GST)

Supply and erection of 2.5 Sqmm x 3-core (Unarmd.) PVC insulated and sheathed Aluminium conductor service cable 1100 volts, having single solid aluminium conductor in each core as per IS:694, complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. Make: Polycab, Havell`s, Grandlay. (Excluding GST).

S/E of 200 Watt LED Flood light luminari of with multiple LED with highly efficient high power LED light with lens, pressure die cast aluminum housing, reflector and enclosed with toughened glass, IP-66 level, having 120 lumens / watt and as per specification attached, with 3 years defect liability period (on site replacement) free of cost, complete in all respect up to the entire satisfaction of Engineer-in-charge of the work. (Make:- Philips /Bajaj/LT/Panasonic/Anchor) - (without GST).

Only Labour charges for ON/OFF operation of all type of LED Light points including Removal of Fault of Circuits. Dismantlement and re-erection of LED fitting from poles for replacement or repairing of LED lights under Defect Liability Period. (2nd Year DLP) (Excluding GST)

Only Labour charges for ON/OFF operation of all type of LED Light points including Removal of Fault of Circuits. Dismantlement and re-erection of LED fitting from poles for replacement or repairing of LED lights under Defect Liability Period. (3rd Year DLP). (Excluding GST)

S/E of 180 Watt LED street light luminaries with multiple highly efficient and high power LED light with individual lens, pressure die cast aluminium housing, reflector and enclosed with toughened glass, IP-66 level, having 120 lumens/watt, with 3 years defect liability period (on site replacement) free of cost, complete in all respect upto the entire satisfaction of Engineer-in-charge of the work.(Without GST) Make- Philips/Bajaj/LT/Panasonic/Anchor