Haryana Urban Development Authority Tender

22.1.3:- Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White vitreous chinaware Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

22.105.1:-Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 22.105.1 15 mm nominal bore

22.107.1:- Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 22.107.1 15 mm nominal bore

13.10.2:- Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 13.10.2 5.5 mm thick glass panes

13.21.1:- Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1 :2:4 for fixing lugs complete in all respects as per drawing, design, specification & entire satisfaction of Engineer-in-charge. 13.21.1 Door Frame of size 80mm x 50mm with 37mm wide single rebate for 35mm door shutter

22.181:- Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

22.88.1:- Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work• Exposed on wall 22.88.1 15 mm dia nominal bore

12.36.1:- Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 12.36.1 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws

12.19.1.1:- Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 12.19.1 35 mm thick shutters 12.19.1.1 with ISi marked M.S. pressed butt hinges bright finished of required size 12.19.1.1.1 Second class teak wood

30.21:- Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

11.78:- Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.

30.27.1:- Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: 30.27 .1 One or more coats on old work

34.51:- Painting on Wood Surfaces Providing and applying two coats of ready mix paint of approved brand on wood surface after thorough cleaning of surface to give an even shade