Haryana Urban Development Authority Tender

[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA

[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole

[23.27.3]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 3. M.S. pedestal of size 750 mm wide , 1200 mm high ,300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0

[24.13.20]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 20. 16 Sq mm 2core (Arm.)

[24.13.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.)

[24.13.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 32. 25 Sq mm 4 core (Arm.)

[24.13.69]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 69. 120 Sq mm 3.5 core (UnArm.)

[24.13.74]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 74. 150 Sq mm 3 core (Arm.)

[24.4.3]STREET LIGHT 3. Supply and erection of 32mm dia metre 1.5 m long bracket (B-class) making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc. including necessary connections.

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia

Replacement of Split A.C. condenser coil copper complete as per manufacturer specification complete in all respect upto the entire satisfaction of Engineer-In-Charge. (Excluding GST).

Supply and erection of LED Panel of 36 W surface mounted having size of 4x1 sqft up to the entire satisfication of Engineer-In-Charge of the work complete in all respect as per approved specifications of make :- Bajaj,Philips and Havell’s.(Excluding GST)

Supply and erection of Compressor for 1.5 TR Split A.C. including filling of refrigerant including rebate of old compressor complete in all respect as per standard specification upto the entire satisfaction of Engineer-In-Chief. (Excluding GST).

Supply and erection of copper pipe 1/4” and 1/2” (in pair) for 1.5/2.0 TR Split A.C. complete in all respect upto the entire satisfaction of Engineer-in-Charge. (Excluding GST) (Unit :-R/Feet)

Supply and Erection of Sensor based AMSON’s/ Indo Asian make automatic Electronic timer to Switch ON/OFF the street / Road light automatically. It will change switching ON/OFF timings automatically on daily basis throughout the year as per change in timing of sun rising and sun setting suitable for street/ Road lights. It will have three contractors of 24 Volt of BCH (Bhartiya Cutler Hammer) to control load upto 40 Amp. Per phase with voltage ratio @230/240. It will have light activated automatic Switching system to switch ON/OFF of the Road street lights. It will have Auto/ manual systems for maintenance of street light during day time. It should have Transformers with voltage ratio 230/240 and other allied accessories as required. Bakelite sheet to assemble the components etc. It should have Kit Kat of 20 Amps capacity to save the time switch from power fluctuation. The device will be housed in the existing pedestal/box/pole etc. in such a way so that it operates at correct timings and erection of the same at site complete in all respect upto the entire satisfaction of Engineer-In-Charge...

Supply, Installation Testing and Commissioning of LED Street Light Fixture with Wattage range of (45 Watt) with body made of High Pressure Single Piece Die Cast Aluminum Alloy and cover made of PMMA (polymethymethacrylate) having system Lumen)120Ipw with inbuilt Protection against Short Circuit, Miswiring, Over Voltage and Surage Protection of 6 KV. The IP of fixture and Driver Comparment should be IP66 and same for the LED Comparment. The driving current should be ( 700mA with THD ( 5% and PF ). 90 and Operating Voltage between 120-270V and CRI ) 70 and Impact Resistance of IK)05. The specifications as mentioned above should be duly tested and Mentioned in LM79 Report from Govt. Approved NABL Accredited Labrotary and LM80 Report of LED Chip from the Manufacturer required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years Including Driver against any manufacturing defect) (Including Three Years replacement warranty and three years Free Mtc./Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture. (Makes: - Bajaj/Phillip’s/GE/LT).

Supply/Installation/Testing/Commissioning of LED T8 Batten Tube Light fitting with wattage range of 20 Watt or other equivalent make and model of Phillip’s/GE/ Bajaj with lense with high power LED T8 Batten light with complete assembly with LED driver and accessories required to complete the job in all respect including erection and fixing including connection and other petty material for the same upto the entire satisfaction of Engineer-in-Charge of the work. (Warranty- 3 Years Including Driver against any manufacturing defect Separate letter head to be given by the quoting agency). The logo of company should be embossed on the fixture.

Supply and erection of 10 Sqmm PVC Twin core sheathed 1100 V grade Aluminium conductor cable complete in all respect as per standard specification upto the entire satisfaction of Engineer-in-Charge (Excluding GST.)