Haryana Tourism Corporation Limited Tender

Air Blower : Supply Installation Testing and Commissioning of Twin Lobe type rotary air blowers ( 2 working & 1 standby ) capable of delivering 365 cum / hr (each) of free air at 0.55 kg / cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415±10%volts,3 phase, 50 cycles a/c supply. MOC of body : CI, Speed : 1200 RPM. Air piping shall comprise of pipes droppers/laterals with MS (epoxy coated) Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good. Make : As per DNIT 3 Nos. (2W+1S)

Air Diffusers : Supply, installation, testing & commissioning of air diffusers (32 nos.) for providing aeration of following :-Diameter of Membranes-90 mmDia/Length-150/2000 mmMOC- EPDM/Silicon Rubber Type -Tube Type Make-As per DNIT

Bio pack Media / MBBR Media : Supply, installation, testing & commissioning of MBBR media of following parameters:-Diameter of Media-20-25 mm Height of Media-10-20 mm Surface Area of Media should be greater than 520 m2/m3. Membrane forming time should be in the range of 3-10 days. MOC of Media-Polypropylene (PP). The design of media and exact size to be approved by Engineer in charge before procurement. Life span greater than 15 years. Make:-As per DNIT (LOT)

Hexagonal Tube Media : Supply, installation, testing & commissioning of tube media of following parameters:-MOC of Media-Polypropylene (PP) Type-Sqaure/HexagonThickness-1.0 to 1.2 mm. The design of media and exact size to be approved by Engineer in charge before procurement. Life span greater than 15 years. Make:-As per DNIT (LOT)

Sludge Recirculation System : Supplying, installing, testing, commissioning of Submersible non clog/centrifugal Sludge Recirculation Pumps. The pump shall be suitable for 415±10% volts 3 phase AC supply. Pumps = 02 Nos.(1w + 1s) TEFC Motor with IP - 55 rating Flow rate (each) = 10 m3/hr Head = 14 mtr MOC of base:- CI MOC of shaft:- SS316 Solid handling capacity-35-45mm Pump efficiency-70% Make:-As per DNIT

Filter Feed Pumps : Supply, installation, testing & commissioning of horizontal centrifugal fiter feed pumps for complete installation with all the accessories. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line- 2 Nos. (1W+1S) Pumps = 02 Nos.(1w + 1s). TEFC Motor with IP - 55 rating Flow rate (each) = 25 m3/hr. Head = 35 mtr MOC of base:- CI MOC of rotor:- SS304 MOC of shaft:- SS304 Pump efficiency-70% Make:-As per DNIT

Pressure Sand Filter - Supply, installation, testing & commissioning of MSEP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like pressure gauges, sampling cock, rinse drain etc Flow-25 m3/hrDiameter-1200 mm Height of Vessel-1500 mmMOC-MSEP Shell Thickness-8 mmDisc Thickness-10 mmFrontal Piping-MSEPSize of Piping-65 NB Type of Valve- Butterfly ValveFiltration Media-Multi Grade Sand Media Quanity - 2000 Kg Make of Valves-As per DNIT- 1 No.

Activated Carbon Filter - Supplying, installation, testing & commissioning of MSEP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like pressure gauges, sampling cock, rinse drain etc Flow-25 m3/hr Diameter-1200 mmHeight of Vessel-1500 mm MOC-MSEP Shell Thickness-8 mmDisc Thickness-10 mmFrontal Piping-MSEPSize of Piping-65 NB Type of Valve- Butterfly Valve Filtration Media-Multi Grade Sand + Activated Carbon Media , Sand + Carbon. Make of Valves-As per DNIT- 1No.

Chlorine Dosing System - Supply, Installation, testing and commissioning of Chemical dosing system comprising of Dosing pumps ( 1W + 1S ) with IP 55 motor rating compatible for the complete dosing system : -Capacity-12 LPH Pressure-5 kg/cm2 MOC- PPDosing Tank Capacity-200 Ltrs MOC Tank-HDPE Make-Pentair/Milton Roy, Pump make: -As per DNIT- 1 No.

Flow meters : Supplying, Installation, testing and commissioning of flow meter of following parameters:-Capacity-25 m3/hrType-Inline pipePipe Size-65 mm Make-As per DNIT- 2Nos.

Sludge Dewatering Unit ( Filter Press) : Supplying, Installation, testing and commissioning of Sludge Dewatering Unit of following parameters:-Plate no-20 MOC of body-MSplate MOC-PP size:-610 x 610 mm Filtration per press : 16 Sqm/press, Cake holding capacity per recessed plate : 20 Litres /Chamber and 400 Litres/press Make-As per DNIT (LOT)

Submersible Sump Pump : Supplying, Installation, testing and commissioning of Submersible sump pump to transfer from receiving sump to Equalization Tank. Pumps = 02 Nos.(1w + 1s) Capacity-60 m3/hrHead-15 meter Type-Cutter type, submersible TEFC motor with IP -68 rating MOC of Pump-SS Power-5.0 kW/ 3 Phase Shaft-SS Efficiency- 70% Make-As per DNIT

Supplying, Installation, testing and commissioning of complete piping and fittings of STP plant. It includes all types of pipes, valves and other accessories as rqeuired and approved by engineer in charge. Submerged Piping-HDPE IS 4984 : 1995 Covered Piping SS 316 Make:-As per DNIT (LOT)

Supply and laying of Sewage Bypass line required in case of maintenance of STP of size 150 mm in DI ( MOC ) pipe having flenge joint with all accessories, fitting, valve etc as required to complete the work. Make:-As per DNIT (LOT)

Supplying, Installation, testing and commissioning of following instruments required for STP plant Level Sensors- 6 Nos Pressure Gauges- 3 Nos. Make - As per DNIT (LOT)

Providing and fixing in position M.S. pipe two side flange sleeves of upto 600 mm long ( heavy class ) with M.S. puddle flange fabricated out of 6 mm thick M.S. plate in RCC walls of water tanks/retaining wall during the time of casting the same including hot dipped galvanisation after fabrication and painting with 2 coats of anti corrosive paint over primer. Size & location of the puddle flange shall be as required to complete the STP system. Make:-As per DNIT (LOT)

Providing and fixing of pH Meter wherever required. Make :As per DNIT - 1 No.

Providing and fixing of Vent pipes over each tanks of any non-corrded material in STP for sufficient numbers of following sizes in all respect and as directed by the engineer incharge. Make:-As per DNIT

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of Motor Control Centre ( MCC ) indoor cubical type ( IP55 ) suitable for 415V, 3 phase, 4 wire, 50 Hz AC supply system fabricated out of 2mm thick CRCA sheet steel & finishing complete with 7 tank process for powder coating in approved shade. Panel should have 2 nos earth stud at the rear, solid connections from main bus bar to switchgear with required size of Copper busbars and control wiring with 2.5 Sq.mm PVC insulated multi strand copper conductor cable, cable alleys, CT, Control Fuse, Voltmeter, ammeter, push buttons, indication lamp, Auto manual selector switches, cable gland plates etc. make:- As per DNIT (LOT) MCC panel shall comply all latest codes and standards and as per approval of Engineer in charge. MCC panel shall be suitabe for all equipments/pumps connected to the STP with 25 % of spare capacity. DOL starters shall be used for the pumps below 10 HP and all other pumps shall have Star Delta Starters. MCC panel shall be mounted floor mounted or mounted on MS stand with proper paint & primer as per the site conditions and as approved by engineer in charge. It should comply with NFPA Norms.

Supply, Laying, Testing & Commissioning of Flexible Electrical Cables of Copper condutor for all pumps and equipments of required sizes as required in 500 KLD STP along with all accessories for termination of the same conforming the required codes and standards. It also includes the Cable tray for laying / routing all cable from panel to equipments as required with proper dressing and tagging of the same. Make of Cables- As per DNIT (LOT)

Supply, Installation, Testing & Commissioning of LED Light fixture ( outdoor type ) as required for the proper illumination in the STP in different area along with the mounting arrangement with GI octagonal poles of required height along with all other accessories. Make of light fixture: - As per DNIT (LOT)

Supply, Installation, Testing & Commissioning of Earthing system conforming IS: 3043 for equipments as required for 500 KLD STP plant. Make:-As per DNIT (LOT)

Supplying, Installation, testing and commissioning of main incoming power cable of size 4C x 120 sqmm XPLE Armoured Al conductor with all termination accessories and laying accessories including HDPE pipe of 100 mm Dia.It should be fixed on wall or laid on ground complete required for STP. Make:-As per DNIT (LOT)

Final painting of plant with colour coding as per PCB norms (LOT)

Contractor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required to complete working of the STP and got it approved by the Consultants / EIC before start the work at site (LOT)

NOTE: The rate also be included the cost of trial run within operation and maintenance of the plant for a period of one year including the cost of consumables complete as specification as directed to obtain required no. of test report of treated/raw sewer during trial run. The bidder has to take this own judgment for designing the system. The cost includes all items required to complete the operation for working of STP complete in all respects all items