Haryana Tourism Corporation Limited Tender

Board Room -Kareena High back chair Specification:- Kareena High Back chiar of Godrej Make : - The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2 kgs as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 76.0cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S tubular armrest support chrome plated. The armrest height shall be adjustable up to 6.5+/-0.5cm in 5 steps and also has swivel adjustment of 22 degree+/-2 on both sides. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee tilt synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat depth adjustment of 6.0+/-0.5cm should be locked in 6 positions. The backrest shall consists of a sliding up down mechanism, Which can be adjusted in the range of 7.5+/-0.5cm and should be locked in 4 positions for correct position of lumber support. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestal shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 101.5 to max 117.5cm. Seat height - min 46.9 to max 55.9cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Board Room -Kareena Mid back chair conf Specification:- Kareena Mid back confchiar of Godrej Make : -The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2 kgs as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S tubular armrest support chrome plated. The armrest height shall be adjustable up to 6.5+/-0.5cm in 5 steps and also has swivel adjustment of 22 degree+/-2 on both sides. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee tilt synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. Seat depth adjustment of 6.0+/-0.5cm should be locked in 6 positions. The backrest shall consists of a sliding up down mechanism, Which can be adjusted in the range of 7.5+/-0.5cm and should be locked in 4 positions for correct position of lumber support. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestal shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 89.0 to max 105.0cm. Seat height - min 46.5 to max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Student Dining Hall- Timeout 6 Seater Specification:- Time Out 6 Seater PU Coated of Godrej Make : - size shall be 1734 Width mm x 1175 Depth mm x 750 Height mm . Top shall be 25 mm thick base material shall be 25 mm MDF board. On top PU painting of minimum 2H hardness with 75% glass as per colorchart.Combinationcolor graphics on the centre. Brown Laminate on bottom specially profiled edges for comfort. The Understructure shall be having bend pipe structure of MS powder coated. Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws. Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top. Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking.

Student Dining Hall- Timeout 8 PU Coated Specification:- Time Out 8 Seater PU Coated of Godrej Make : - size shall be 2329 Width mm x 1175 Depth mm x 750 Height mm . Top shall be 25 mm thick base material shall be 25 mm MDF board. On top PU painting of minimum 2H hardness with 75% glass as per colorchart.Combinationcolor graphics on the centre. Brown Laminate on bottom specially profiled edges for comfort. The Understructure shall be having bend pipe structure of MS powder coated. Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws. Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top. Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking.

Student Dining Hall- Unwind café chair-SS Understructure Specification:- The seat & back are made of injection moulded high impact strength PPP compund with indoor grade UV resistance seat size 52.5cm ( W) * 53.2cm back size 51.6 cm (w) 40.5 cm H , SS powder coated under structure . Shoe are made of high impact strength PPP compound with indoor grade UV resistance and assembled over the tabular frame . Armrest are made of high impact strength PPP compound with indoor grade UV resistance and assembled over the tabular frame.

Wish Workstation for Computer Lab and Library Supplying Recta Workstation of size 1200WX600DX750H:Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1045mm. including powder coated aluminium trims. Tiles: Combination of top tiles are fabric Tackable tile. Bottom tiles - Plain metal.SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric tackableINTERMEDIATE BLOCKS Intermediate blocks are given in Decorative Laminate finsh. BIFMA LEVEL 2 Certified .Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks.Legs - System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface- 25 mm thk pre laminated particle board with flat pvc lipping edge banding of size 1200WX600DX750H . : All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring.+ Pedestal +KBPT+CPU Trolley.

Library- 4 Door Bookcase (New without Top)-1742Hx914Wx320D Specification:- 4 Door Book Case of Godrej Make : - shall have the configuration of 914mm(W)x320mm(D)x1742mm(H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Panel, Back Panel and Side Panel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision which shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 2 Door Book Case shall have 18mm PLB Top straight edge with PVC Lipping. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

Library- All steel Periodical Display Rack- 1830Hx900Wx450D Specification:- PDR all Steel of Godrej Make : - Overall Dimensions of All Steel Periodical Display Rack shall be 900mm(W)x450mm(D)x1830mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.6 mm thick and front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . There shall be 5 level racks , Display tray shall be suitable for foolscap size magazines, periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveller shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns .

Library- PCH 7043 Chair without arms Specification:- Diva Vistor chair without arms of Godrej make : - The seat shall be made from 1.2 ±0.1cm. thk. hot pressed plywood and back shall be injection moulded from black Co-polymer Polypropylene upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of seat shall be 45.0cm(W) x 42.0cm.(D) and of back shall be 39.0cm(W) x 38.0cm.(H). The seat and back covers shall be injection moulded in black Co-polymer Polypropylene. The HR polyurethane foam shall be moulded with density = 45 +/-2 kg/m3 and hardness load 16 ± 2 kgs as per IS:7888 for 25% compression. The fixed type mechanism shall be without back tilt. The tubular frame shall be made up of dia 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S.E.R.W. tube and black powder coated (DFT 40-60 microns). The overall dimensions of chair shall be Seat Height -45.0cm, Height -81.5cm, Width & Depth of Chair as measured from pedestal - Width-45.0 cm and Depth-54.0 cm.

Class Room- GENII 3 seater of Godrej Make : - size1840 x 1130 x 757 – all side metal frames and cross connection are made from combination of 23.4 * 1.2 mm thik ( approx 18 SWG ) round ERW tubes , 31.8 * 1.2 mm thk ( approx 18 SWG ) Round ERW tubes and 28.6* 1.2 mm thk ( approx . 18 SWG ) Round ERW tubes ( As per IS :7138 ) which are welded together . The Welded structure and cross connectors are coated with with min. 45 micron thickness of epoxy polyester coating .Green Guard Certified . Back support which provided at the rear back are made of 50.8 * 25.4 * 1.2 mm thk( approx 18 SWG ) rectangular ERW tubes ( As per IS : 7138 ) . The tubes are coated with min 45. Micron thickness of epoxy polyester coating . The storage shelves are made from 0.6,,thk sheet ( As per IS: 513 ) fixed below the desk top panel and are coated with min 45 micron thickness of epoxy polyester coating . Hooks are provided on the vertical side frames on both sides of the desk for hinging bags/ bottles . They are made from 2mm thk MS sheet ( As per IS : 513 ) and are coated with min 45 micron thickness of epoxy polyester coating . The understructure is assembled using M6 trilobular screws ( As per DIN 7500 ) with Zn blue plating ( As per IS 1573:1986) . Compact laminate seat and back panels are assembled using M6 Countersunk trilobular screws ( As per DIN 7500 ) with Zn black plating ( As per IS 1573:1986) . Spacers are provided on the top of round tubes for wooden panels fixing . They are mad of PP Glass filled ( 30 %). Plastic Caps made of PP copolymer ( 3530 Grade ) are also provided on the rear frames adding more aesthetic value to the product. M6 high tensile TVS make bolt ( class 8.8) with glass filled nylon level adhustors are provided at the bottom of understructure to take care of unevenness in floor with height adjustment of approx 15 mm .

Total 450 Lockers – 6-door PU (1+2) single unit 4’ width Total 450 Lockers - 6 - Door PLU + Lkr (Base) - 1830Hx380Wx450D IN MM Specification:- 6 door plu base of Godrej Make : - Overall size of 6 - Door PLU - Lkr (Base) shall be 380mm(W)x450mm(D)x1830mm(H). DMX Drg.- PL 13-A4-33797,R1 - 4 Sheets(Cam Lock) DMX Drg.- PL-13-A4-36467,R1-4 Sheets(Hasp.) Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation .

Total 450Lockers - 6 - Door PLU + Lkr (Add On) - 1830Hx380Wx450D Specification:- 6 door plu add on of Godrej Make : -[ Overall size of 6 - Door PLU - Lkr (Add On) shall be 380mm(W)x450mm(D)x1830mm(H). DMX Drg.- PL 13-A4-33797,R1 - 4 Sheets(Cam Lock) DMX Drg.- PL-13-A4-36467,R1-4 Sheets(Hasp.) Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation

Total 450 Lockers - Stand for three lockers ( Black) Specification:- Locker Stand of Godrej Make : - Overall size of stand for one locker(black) shall be 380mm(W)x450mm(D)x125mm(H) . 10 Lever cam lock with lock lever plus option of Hasp arrangement .

Instructor Table T 8 for Kitchens,class rooms and house keeping lab Specification:-Table - T 8 size shall be 1199 Width x 590 Depth x 735 Height. The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides. Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be dia. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube.Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS. Also there should be 10 lever cam lock plus handles built in plastic.

Instructor Table T 8 for Kitchens,class rooms and house keeping lab Specification:-Table - T 8 size shall be 1199 Width x 590 Depth x 735 Height. The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides. Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be dia. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube.Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS. Also there should be 10 lever cam lock plus handles built in plastic.

House Keeping – Insight 1665W - 6 Seater Specification:- Insight Table of Godrej Make : - size shall be 1665 Width mm x 900 Depth mm x 740 Height mm. The top shall be 25 mm thick PLB with 2 mm thick PVC Edge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top. The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube.

SITC Projector with brightness of 4000Lumens, WXGA Resolution, 3 LCD projector, having HDMI , VGA along with ceiling mount

SITC of 113 inch motorised screen.

SITC of 15 meter HDMI cable and 15 meter VGA cable