Haryana Power Generation Corporation Limited Tender

SEATED PULLER/PULL CHAIR DIMENSION 1900 mm (Length) x 740 mm (Width) x 1920 mm (Height). SAFE AREA: - 1.2 Mtr x 3 Mtr. `Providing and fixing seated puller made from ‘B’ Class Medium GI Pipe. The center pipe is of 100mm NB made from ‘B’ Class Medium GI Pipe and the bottom support of M.S. round plate of 250 mm dia and 10mm thickness is welded at bottom. The remaining frame is made up of 30mm NB ‘B’ Class Medium GI Pipe. The handle frame is of 25mm NB ‘B’ Class Medium GI Pipe. The seat frame is of 30mm NB ‘B’ Class Medium GI Pipe, for the assembly different bushes are used which is made from seamless pipe of 50mm 00 and 3mm thickness and 50mm solid bar is used. The seats are made up of high quality FRP material of size 330mm X 330mm of thickness 3mm and M.S. Plate of size 250mm X 200mm X 5mm is used to support it. Closing caps made from high quality FRP material which is of 2mm thickness. The pins used are made up of 17mm diameter solid bar. The bearings used are of `6203` permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly are of 17mm diameter. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18 mm thickness and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated.

LEG PRESS DIMENSION 894mm (Length) x 853mm (Width) x 1203mm (Height). SAFE AREA: - 1.2 Mtr x 3 Mtr. `Providing and fixing Leg Press made from ‘B’ Class Medium GI Pipe. The center pipe is of 100mm NB made from’B’ Class Medium GI Pipe, and the bottom support of M.S. Round plate of 250 mm diameter and 10mm thickness is welded at bottom. The remaining outer frame is of 40mm NB made from’B’ Class Medium GI Pipe. To join the centre pipe and outer frame seamless pipe of 130mm dia and 3mm thickness is used. The seats are fitted on the outer frame is made up of FRP material of size 330mm X 330mm of thickness 3mm and M.S. Plate of thickness 5mm and Size 250mm X 200mm is used to support it. The footrests is made from FRP/C.I.I Aluminum casting material, its sizes are 130mm X 300mm and 5mm thickness. The frame of footrests consists of 25 NB made from ‘B’ Class Medium GI Pipe. Closing caps made from top quality FRP material which is of 2mm thickness. The inner bushes are made from seamless pipe, its diameter is 60mm and 8mm thickness. The pins used in are made up of 25mm diameter hardened bright bar. The bearings used are of `6205` permanent anqle don by attractive qolor spravinq after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated. To join the centre pipe and outer frame seamless pipe of 130 mm dia and 3mm thickness is used. The seats are fitted on the outer frame is made up of FRP material of size 330 mm X 330 mm of thickness 3 mm and M.S. Plate of thickness 5mm and Size 250mm X 200mm is used to support it. The footrests is made from FRP/ C.I./Aluminum casting material, its sizes are 130mm X 300mm and 5mm thickness. M. S. plate of 280 mm x 130 mm x 5 mm thickness is used. Closing caps made from top quality FRP material which is of 2mm thickness. The inner bushes are made from seamless pipe, its diameter is 60mm and 8mm thickness. The pins used in are made up of 25mm diameter hardened bright bar. The bearings used are of `6205` permanent lubricated sealed bearing of reputed make. The handles used are of Rubber grip. The Nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Polyurethin Plastic material of 50mm diameter. The serclipsed for assembly are of 25mm diameter. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18 mm thickness and painting is lubricated sealed bearing of reputed make. The handles used are of Rubber grip. The Nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Polyurethin Plastic material of 50 mm diameter. The serclipsed for assembly are of 25mm dia meter. The Foundation pipes are embedded in C.C. stock and paintings.

Cycling Instruments/Arm and Paddle Bike Dimension:- 1100 mm (Length) x 500 mm (Width) x 900 mm (Height). Safe area:- 2000 mm (Length) x 1000 mm (Width). Arm and paddle bike made from “C” class G.I. pipe. The center pipe is of 40mm NB made from “C” class G.I. pipe. The handles are made up of casted iron material with plastic holding grips. For foundation holes pass provision is provided. The footrests is made from Aluminum casting material, its sizes are 130 mm x 300 mm and 3 mm thickness. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18 mm thickness. The seats and bank rests are fitted on the outer frames are made up of M.S. sheet of size 280 x 130 x 5 mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The pins used is made up of 25 mm diameter harden low carbon steel. The bearing used is of “6205” permanent lubricated sealed bearing. The nut bolts used for assembly are made from S.S. material. The gym equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based powder coating with polyester powder coating of at least 60 to 70 micron thickness using Exonoble/Berger make paints or its equivalent paints. The holding down/fixing of Gym equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand : 4 stone agg. 20 mm nominal size.).