Haryana Police Housing Corporation Tender

[13.30.3]Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 3. Electric resistance or induction butt welded tubes [Through Rate]

[13.32]Providing and fixing bolts including nuts and washers complete. [Through Rate]

[20.72]Supplying, errection, testing of Exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge. [Through Rate]

[22.173.1]Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 1. With common burnt clay non-modular bricks of class designation 7.5 [Through Rate]

[23.22.1.10]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.10. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 125 to 160 amp, 25 KA [Through Rate]

[23.22.2.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 2.1. MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP [Through Rate]

[23.22.4.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.5. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) [Through Rate]

[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate]

[23.22.5.8]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.8. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs FOUR POLE [Through Rate]

[23.22.6.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 6.5. Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. FP RCCB 30ma sensitivity , 40 A [Through Rate]

[23.26.1]SAFETY ITEMS 1. Supply and erection of Medium Voltage caution notice plate of size 200*150 mm in three languages. [Through Rate]

[23.26.3]SAFETY ITEMS 3. Supply and erection of shock restoration chart in glass frame. [Through Rate]

[23.5.6.1]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) [Through Rate]

[23.5.6.5]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.5. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 10 Sqmm(1/3.50 mm) [Through Rate]

[23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. [Through Rate]

[23.8.1.12]FITTING AND ACCESSORIES 1.12. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size. [Through Rate]

[23.8.12]FITTING AND ACCESSORIES 12. Supply and Fixing 3 mm thick Bakelite sheet cover on existing MS/PVC junction box/tee etc including fixing with brass screws and washers. [Through Rate]

[24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. [Through Rate]

[24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. [Through Rate]

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.13.40]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 40. 35 Sq mm 4 core (Arm.) [Through Rate]

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate]

[4.14.1]Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil. [Through Rate]

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) [Through Rate]

[6.14.1]Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) [Through Rate]

[6.29.1]Centering and shuttering including strutting, propping etc. and removal of form work for : 1. Foundations, footings, bases for columns [Through Rate]

[6.33.6]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6. Thermo-Mechanically Treated bars of grade Fe-500D or more [Through Rate]

NS PART Supply , Installation, testing and commissioning of Emergency Rescue Device (ERD) with batteries complete in all respect. (For 8 Passenger Lift) 1) LIFT ERD :- ERD 15KVA (Su-vastika Make) 3 Phase In 3 Phase Out * with Isolation Transformer * Micro Controller based IGBT Technology * Advanced Technology: DSP based Controller for power and monitoring * True Online dual conversion design * Equipped with rescue Trip feature after Batteries are fully exhausted * Complete in all respect including stand. 2) BATTERIES- Lithium Battery 5.7 KW with 1 hour Backup. (Su-vastika Make)

Supply, installation, testing and commissioning of 1100 mm (nominal size), 20 watt LED batten luminaire in PC housing with minimum light output 100 lumen/watt and Toatl system lumen )2000 lumen THD (20%, PF )0.95. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.(as per HPHC Brand list) ( Make-Phillips / Havells / Wipro / Bajaj)

4mm thick Aluminium Composite Material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided. (RM 173, CODE)

Supply, erection, testing and commissioning of 8 passengers (G plus 3), Electrical Traction Elevator Roomless, Gearless with With minimum Speed of 1.0 mtr/Second serving 4 Stops and 4 Opening with full glass vision door, all 3 side observation glass car with S.S. framing, Granite flooring on heavy duty M.S. Platform, Decorative False Ceiling With CFL/LED Lighting, Blower/Rotor fan, SS Vandal finish, hand rail for physically disabled, Mirror and Antiskid PVC Flooring to be erected in accordance with the following Technical Specification and as per latest IS Specification. (i) Make of Lift :- OTIS / KONE / MITSUBISHI / SCHINDLER/ORBIS ii) Type and capacity : Passenger Elevator App. 544 Kg 8 person iii) Speed : 1.0 mtr per second iv) Travelling (max) in mtrs : Approx. 11 mtrs v) Serving: (G plus 3) 4 stops, 4 opening all opening on same side) vi) Power Supply : 415 V, 3 phase, 50 HZ A C supply. vii) Control : High Performance simplex full collective integrated serial communication control system. viii) Operation : Automatic ix ) Motor : Permanent Magnet Synchronous Electric Traction Gearless Motor to be hoisted on guide rail within the elevator hoist way x) Location of Motor : Motor to be hoisted above the rail within the elevator hoist way. xi) Type of Drive : A. C . Variable Voltage Variable frequency with 16 Bit Microprocessor xii) Car inside area : 1300 mm Wide x 1100 mm Deep (1.43 Sq. meter) xiv) Car Enclosure : all 3 side observation glass car with S.S. framing, Granite flooring on heavy duty M.S. Platform, Decorative False Ceiling With CFL/LED Lighting, Blower/Rotor fan, SS Vandal finish, hand rail for physically disabled, Mirror and Antiskid PVC Flooring to be erected in accordance with the following Technical Specification and as per latest IS Specification. xv) False Ceiling : Stainless steel false ceiling in hair line finish xvi) Car Panel : stainless steel (scratch free) Hair line finish xvii) Flooring : G ,1,2,3, xviii) Clear Opening of door : 800 mm wide x 2000 mm Height xix) Door Operation : Automatic DC/AC with adjustable Door Opening and closing timings with center opening sliding door x) Car Door : Center opening automatic door (Full Vision Glass Door With S. S Frame Scratch Resistance Finish). Landing door : Center opening automatic door (Full Vision Glass Door With S. S Frame Scratch Resistance Finish) Other Features: i) Battery operated intercom, emergency alarm and emergency light with maintenance free rechargeable battery. ii) Adjustable guide shoes.(Ensures good ride comfort) iii) Digital direction and position indicator in Car and at all landings. iv) Integral full height car opening panel with luminous combined with direction arrows, overload warning indicator and services cabinet v) Hands free press and speak intercom with EPABX for three way communication. vi) a) Automatic rescue device(ARD) to rescue the Passenger in case of emergency the device will bring the elevators to the nearest floor and open the door automatically in Case of power / phase failure / low voltage. b) Manual Rescue lever vii) Full height infrared safety curtain( Highly sensitive safety device for safe entrance and exit of the Passenger into the Car and automatic floor announcer. viii) Diffused lighting in car. ix) Cross flow fans=2 Nos. x) Looking mirror in side of lift car. xi) Face plate Finish : stainless steel in hair line. xii) Face plate : Rectangular. xiii) A three feet high railing shall be provided on car top xiv) The motor shall be high starting torque and low starting current and shall be arranged for self lubrication. xv) Proper weight screen shall be provided at the hoist way. xvi) Fire retardant compound coated traveling cable shall be used. xvi) 2 Phase Device Fire Man Drive and Fireman switch at ground floor xvii) Micro Movements L.E.D. based Buttons . xviii) Load Weighing device with overload bypass feature.(Audio Visual over load indicator in the car) xix) Steel items such as Door Frames Sill Angles, Fascia Plates, Spring Buffers. xx) Braille fixtures, Lift announcement system, Pit ladder, Hand rail , Pressure sensing device and Additional Car Gate Lock. xxi) Three Side Hand Rails in Stainless Steel Finish xxii) System Capable of withstanding plus 10% to –10% Variation in Supply Voltage Fluctuations. (C.V.T should be provided for Protection of lift against Single phase, Low voltage and over voltage) xxiii) Car Platform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel xxiv) The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice and vibration. xxv) A handrail not less than 0.60 mtr long and 1.0 mtr. Above floor level shall be fixed adjacent to the control panel.. xxvi) The time of automatically closing door shall be minimum 5 seconds and the closing speed shall not exceed 0.25mtr./ Seconds xxvii) Overspeed governor (Electro-mechanical device that prevents free fall in case the lift is travelling at speed more than 10% of the rated speed in downward direction) xxviii) All other required features relates the operation of lift by the Handicapped and Blind person and others as per instruction of lift inspector and HBC 2017 complete in all respect as per Engineer in Charge including transit insurance and storage insurance at site till handing over. Supplier shall provide NOC and inspection certificate from the Lift Safety deptt. of Govt. /Statutory body (Confirming IS -14665 Specifications).