Haryana Police Housing Corporation Tender

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.HSR 9.18

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): HSR 5.8.3

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. HSR 5.14

20 mm cement plaster of mix 11.10.1 1 :4 ( 1 cement: 4 coarse sand) HSR 11.10.1

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete. HSR 11.58

Providing and applying waterproofing treatment using two component 100% solid content hybrid polyurea/polyurethane, rapid curing and highly resHient fully bonded cured to membrane having a mixed density of 1.02g/l. Minimum recommended coverage rate is 1.5Hr/sqm in 2 coats to achieve a total DFT of 1.5mm. cured membrane shall exhibit: 1) Tensile strength ASTM D412: 13 MPa 2)Tear Resistance ASTM D624C : 50 N/mm2 3) Shore A Hardness: BO 4)Elongation ASTM D412 : 450% 5 ( 1kg, CS 1Dwheels,ASTM D 4060): 1.3 mg/1000 cycles 6) Service temperature: -20"C to +BO"C 7) Resistant to Fire (EN13501-1)-Class E,dO Manufacturers shall provide Certificate for Zero voe, resistance to fire, 25 years life expectancy test certificate before the start of work. System indudes supply , application and termination of coating all complete as per the manufacturer methodology Clean the RCC slab/screed surface & wall for treatment by removing dust, dirt and layers of concrete over the surface. etc. by mechanical tools and wire brushing. Pressure grouting at construction joints or honeycombs with non shrink cementations grout by mixing shrinkage compensating admixture per bag of cement as per manufacturer's recommendations. Prepare a side gola of 50X50 mm at the junction using polymer modified mortar. Providing and applying two component 100% solid content, hybrid polyurea/polyurethane membrane at coverage rate of 1.51tr/sqm in 2 coats to achieve a total DFT of 1.5mm. It must be applied utilizing plural heated high-pressure spray proportioning machine/spray gun . Termination shall be done 300 mm above FFI by providing a groove cut of 30mm x 30mm & seal it with shrinkage compensated polymer modified mortar. Lay a 150 GSM geotextile layer to protect the coating from external damage on final coating before laying of screed concrete/final finish. It shall be applied as per manufactures specification. Rates are incl of surface preparation, grouting and chemical application only. (Rates for geotextile, protection plaster and final finishes such as screed or Brick bat filling for slope, china mosaic, tiles etc is not included in above item. It will be added as per EiC/clients requirements). HSR 28.7

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in. HSR 7.22.1

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.HSR 22.85.3

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.HSR 22.85.4

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): : HSR 22.98.3

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. HSR 22.103.2

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.HSR 30.17

Finishing walls with Acrylic Smooth exterior paint of required shade: HSR 30.37.1

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.HSR 30.89

Cleaning of terrace/loft water storage tank (inside surface area) up to 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.1 O per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) HSR 30.90

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. HSR 22.181

B0146 Brick bats

HSR Electrical

Supply & erection of LT phase separator on LT line complete in all respect up to entire satisfaction of the Engineer-in-charge of the work .24.2.2.1 2.5 Sq mm to 10 Sq mm 2 to 4 Core HSR 24.2.2.1

Supply and erection of MS conduit pipe 1.6 mm thick , ISi marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.HSR 23.6.6.3

MCCB ,DISTRIBUTION BOARDS, MCB's, RCCB's, CHANGE OVER etc. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. 23.22.4.2 SPN DB Double Door 8 way ( 2 incoming and 6 outgoing) HSR 23.22.4.2

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 23.22.5.1 6 amp. to 32 amp Single Pole. HSR 23.22.5.1

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 23.22.5.4 40 amp to 63 amp. Double pole. HSR 23.22.5.4

CREDIT OF OLD MATERIAL

NS Electrical

Supply of LT unarmoured cable of following 1100 Volt and comlete with making necessary connection of cable on both ends including loading, unloading and carriage with all labour and petty material required to complete the job upto the entire satisfaction of Engineer-in-Charge of the work 1) LT unarmoured cable of size 10sqmm 2 core. NS

Supply and erection of new generation energy saving and environmental friendly, long life, pressure die-cast aluminium housing flood light 150 watt with PC diffused lens enclosure over LED for glare free light. Make as approved brand list of HPHC. NS