Haryana Police Housing Corporation Tender

[23.22.8.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 8.4. SITC Four pole ON LOAD Manual change over switch in SS enclosure of following Ratings 300 amp 415 volts

[23.24.1]MS STAND, BUS BAR CHAMBER AND PANELS 1. Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide.

[23.26.2]SAFETY ITEMS 2. Supply and erection of High Tension Voltage caution notice plate of size 250*200 mm in three languages.

[24.3.4.1]HT CABLE 4.1. Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm

[9.47.5]Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main `T` runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross `T` of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main `T` at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross `T` of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main `T` runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 5. 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

NS PART Supply of XLPE (E) 11 KV HT aluminium conductor armoured cable ISI mark laid in 1 meter below ground level with sand and bricks with all labour and material including digging and refilling of trench, required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work i) Size 50 sqmm 3 Core XLPE cable............................(-)

Supply and Erection of UL Certified Linear pneumatic Heat Detection Tube for automatic fire detection and suppression system made by special modified polyamide (PA), colour red RAL300, burst temperature 100°C to 140°C, inner diameter 4mm, outer diameter 6mm. Pressurized with dry nitrogen at 15 bar pressure with all necessary fittings and supports.

Supply and Erection of UL Certified Extinguishing agent filled in PESO Approved Filling Station: 5 Kg FK-5-1-12 Clean agent filled in PESO approved stored pressure type seamless steel cylinder as per IS 7285 with DLP Valve Assembly, Safety Burst Disc at 28 Bar and Mounting Bracket with all necessary fittings and supports Stored Pressure type fitted with Pressure gauge, UV Resistance, Operating Pressure 15 bar, Hydraulic Pressure Tested to 250 bar, Burst Pressure at 350 bar, Red Powder coated

Supply and Erection of Master Control Unit with audio visual alarm Control Panel, 12 Volt battery, 2 NO/NC potential free relay contact for Main Fire Alarm/ BMS/ SCADA Integration. Gas discharge led indicator, battery led indicator, system status Led indicator , AC power ON Led indicator with all necessary fittings and supports

Supply, Installation, Testing and Commissioning of Rodent System having following specifications: - Microprocessor based Main Panel / Controller wall mounting type with facility to connect 20 Transducers Operating Frequency ) 20Khz and ( 60 Khz. with 4 frequency bands Front Facia having LCD display and on board controls to view and operate the menu. Panel to be with power supply supporting 230V AC.Panel to have BMS Compatibility. (Up To 24 TRANSDUCERS ) TRANSDUCERS (12 nos.), BRACKETS (MS POWDER COATED), Standard 2 core 0.5sq. Mm PVC insulated wire complete in all respect.

Providing and Fixing of ABC Type 6 kg (Stored Pressure) Fire Extinguisher filled with Mono Ammonium Phosphate Powder MAP 50% Confirming to ‘IS 4308’, Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose and Nozzle and Epoxy Polyester Powder Coated Mild Steel body, Fire Extinguishers As per ‘IS 15683 : 2018’ ISI Marked

Providing and Fixing of Carbon Di-oxide Trolley Type 9 kg Fire Extinguishers filled with CO2 Gas Confirming to IS ‘15222’, Cylinder Confirming to ‘IS 7285’ and PESO Approved, Controllable Discharge Mechanism Discharge Hose ,Horn and trolly, Painted Mild Steel Body As Per ‘IS 16018 : 2012 ISI marked

Providing and Fixing of Mechanical Foam Based 45 Ltr Trolley Mounted Fire Extinguisher, Inside CO2 Cartridge Operated Gas Cartridge Confirming to ‘IS 4947’ Discharge Hose and Nozzle, Epoxy Polyester Powder Coated Mild Steel Body As per ‘IS16018 : 2012` ISI marked

Providing and Fixing of Dry Chemical Powder 50 kg (ABC Type) Trolley mounted with CO2 Fire Extinguisher filled with Dry Chemical Powder MAP 50% Fire Extinguisher filled with Mono Ammonium Phosphate Powder Confirmingto ‘IS 4308, Pilot Operated, CO2 Cylinder confirming to ‘IS 7285’ `respectively and PESO approved Extinguisher Suitable for `A` ‘B’ ‘C’ Class of FIRE as per IS 16018 : 2012` ISI Marked

Providing and Fixing of Soft Fibre Acoustical Suspended Ceiling System Tiles With 15mm Exposed Grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.85 – 0.9, Light Reflectance =85%, Colour White/black, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 and7) in module size of 600 x 600 x 15mm, suitable for Green Building application, with Recycled content of 66% GW and 74% RW. The tile shall be laid on Silhouette profile grid system with 15mm white flanges incorporating a 6mm central reveal in white/black colour and with a web height of 45mm and a load carrying capacity of minimum 15.68 Kgs/m2 with a minimum pull out strength of 100 kgs. Silhouette, Main Runners and Cross Tees to have mitred ends and “bird’s mouth” notches to provide mitred cruciform junctions. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of approved make. The Tile and Grid system used together should carry a 10 year warranty. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum centre. MAKE: ANAKON/HUNTER DOUGLAS/ECOPHON (Upto any height).

Providing and Fixing of Spandex System on G.I studs 2400mm X 50mm web flanges 15 and 50mm fully knurled giving it high strength, hot dipped galvanized steel With 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing 50mm thick Rock wool @48kg density insulation intact with chicken mess wires. 600x1200x15mm Magnesite pine wool tile with NRC 0.9-1 to be mechanically fastened on the G.I Studs. Then 12mm clip rail system are screw fixed on to the 12 mm MDF waterproof and Acoustics panel’s .Then the Spandex is stretched over the clip rail system. The installed system should provide NRC OF 1.00. Spandex colour as per Architect choice-Ref attached specifications for more details. The system to be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 and 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration. MAKE: ANAKON/ECOPHON/HUNTER DOUGLAS (Upto any height).

Providing and fixing 15mm thick coloured Acoustic Panels in size 1220 x 610mm of Natural panel having Premium Square Edge. Panels are made of Pine Wood fibers containing cellulose binded with Magnesite. The panels will be screw fixed @ 200mm on GI metal frame of 50 x 50mm making a grid of 610 x 610mm c/c. The frame is to be made in proper line after leveling. The panels will be backed with 50mm Rockwool of 24 kg/cum inserted inside the grid of 610 x 610mm which will comprise of minimum NRC 0.90 as per IS: 8225/ ISO: 354/ ASTM: 423 – 90 a. The panel meets the stringent fire test required having Class ‘P’ rating for Ignitability test as per BS 476 part 5 and Class ‘1’ rating as per BS 476 part 7 for Surface Spread of Flame test. Class ‘P’ and Class ‘1’ are the highest rating. BS 476 part 6 Fire Propagation index, I = not greater than 4.11. It should meet all technical parameter. MAKE: ANAKON/BAUX/ECOPHON (Upto any height).

Providing and Fixing of Magnesite pine wool tile made of mineral wood fibers magnesite bonded having thickness of 15MM tile Suspended on 24 mm strong Grid. The tiles should have Humidity Resistance (RH) of 90%, NRC 1.00, with Fire Rating as per BS476 (Part 6 and 7) in module size of 595 X 595 X 15 mm@ 400kg/m3 density. The tile should have color option as per architect/person in charge (Color on tiles will be extra).Tile would be backed with 50mm glass wool insulation to achieve desired level of acoustic. The grid should be 24 mm wide T sections i.e. the Main Runner 3000mm in web height of 38 mm, 1200 mm and 600 mm Cross Tees in web height of 26mm. Installation to comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system at 1200mm maximum center. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm center to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers and as per the drawing and the work complete in all respects to the satisfaction of Engineer in-charge. All accessories consisting of HLC Sleeve Fasteners of thread size 6.5mm x 25/5 with Soffit Cleat made of Galvanized steel of size 27 x 37 x 25 x 1.6mm and Level Clip in dimensions of 85x30x0.8mm with 4.00 mm GI wire. MAKE:ANAKON/BAUX/HUNETR DOUGLAS (Upto any height).

Providing and Fixing Acoustical Wooden Stage Flooring Compatible with Underground signal cabling and Pop-Up Boxes: Providing and fixing 65/75 X 18 thick in random length, 2nd class teak wood planks flooring with tongue and groove joints on a layer of 15 mm thick Engineering wood of approved make and manufacture, fixed to hardwood joint 50 X 50 mm at 600 mm c/c in one direction and 60 X 50 mm Sal battens 600mm c/c on other direction, Hardwood joint resiliently supported on 100 X 100 mm Rubber Pads, the framework to be filled with 50mm thick Insulation Wool resin bonded insulation of density 24kg/cum. PU polishing of teakwood on the exposed surface: In horizontal/vertical plane (rate for flooring shall include providing additional framework required for housing microphone and power outlet junction - signal and Popup Stage boxes, If required providing and fixing hinged 18mm thick Engineering wood cover for the junction boxes. Work complete in all Respect. The Work shall be executed as per drawings, Specifications and Instruction of engineer in charge.MAKE:Greenlam, ACTION TEASA, Lemiwood.

Providing and fixing of Woven vinyl carpet floorings series with roll dimensions of 1.8/2mtr meters width and length of 20 meters or Tiles size as per company standard should be approved by architech. 2.50-2.80 mm thickness to laid on hard, levelled, smooth and moisture free sub floor. Woven Vinyl flooring should have traffic classification 33 and weight of 2.7-3.5 kg/m2. Flooring should have caster chair EN-985 tested with color fastness of more than 6. It should be ASTME662 qualified on Smoke density test. Product must be fire rating of the product should be Bfl-S1. Any Joints in flooring rolls should be sealed with cold welding.As per approved shade and colour as per the satisfaction of the Architect.MAKE: LG/ Woderfloor.

Supplying and Fixing of Radium glow Stair case Nose made out of anodized aluminium profile having UV exposure shrinkage, anti slip resistance comes in different colour and sizes with the length of 2.5mtrs (Make ANAKON/DURAL/MEISER.

Providing and fixing 12 mm thick and 100 mm high teak wooden skirting over panel frame work and finishing the same with malamine/laminate. (Make GREENLAM/CENTURY/ACTION TEASA).

Supply, installation, testing and fixing of MAIN FRONT VERTICAL CURTAIN made out of glazed cotton cloth with verticaly upward and Downward arrangement complete with fixing rails, brackets, moterised opration complete with required gear box, mini drums, weights, limit swithes, cuplink, runners, master runners,pullies, 3mm steel rope wire, 2HP motor (Crompton). 2 nos air breaker contactors (Landt/Siemens). Push buttton for stop, upward and downward positions.Motor mounting with C channel platform on side wall. Curtain cloth should be fire retarhdant Make D.Decore(Home India)/ ASIAN/ GM.

Supply, installation, testing and fixing of Stage frills having size as required at stage as per site to be installed above the stage on 28mm dia GI pipe adjustable at position according to stage positioning plan. Cloth material of desired shade with Stitching and fire retardant

Supply, Installation, Testing and commissioning of Rotatable Side wings made with 50 x 25 mm square pipe with rockwool insulation inside and covered with 6mm ply both side over which stretch fabric of approved colour to be applied

Provided and fixing stage Proscenium to be fabricated on site made top side with 50x50mm MS square pipe. left and right proscenium wall fixed by using GI Framework spaced at 600mm c/c aluminum framework system is backline with 50 mm Roxul Rockwool and along with all accessories Infill in rockwool insulation padding. Fixing on 12 mm waterfroof ply.finishing with 1mm sun mica approved.

Providing and fixing Fully Insulated Wooden door at all levels. Main Door frame shall be Single rebate profile of section 120 x 70 mm made out of Hard wood - Red meranti / Ivory Coast (2nd class ) as per requirement with factory made groove of suitable size. Wooden shutter must be of minimum 52mm of thickness finished with commercial ply on both faces. The Commercial ply may also be pasted with Laminate in desired shade (payable in extra item). The composite thickness of the core insulation will be 44mm consists of lumber boards of approved make and treated wool Insulation material. The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed wooden lipping . All hardware’s, Fasteners and FR Glass shall be payable in Extra item. Door shutter provided with commercial ply on both faces with 1mm Thick Regular SF grade Factory pasted Laminate on both faces and Main frame made out of hardwood frame. Frame primed with Fire retardant primer. FIXTURES OF DOORS: (A) Supply and fixing of SS Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws (4 No’s per panel), (B) Supply and fixing of anchor fasteners of M10X120mm length. (C) Supply and fixing of door closers of (Except shaft door). (D) Supply and fixing of Stainless Tower Bolt 300mm Long for Double leaf door of height up to 2100mm with necessary screws as required. (E) Supply and fixing of Stainless Tower Bolt 600mm Long for Double leaf door of height up to 2400mm with necessary screws as required. (F) Supply and Filling the gap between wall and Door frame by using silicone sealant and Wool insulation on both side of the door.MAKE: ANAKON/NAVAIR/MAHABIR.

Supplying and placing ergonomically designed designed, comfortable and aesthetically appealing Auditorium chair. The seat shall be made of 12mm thick hot pressed plywood with HR polyurethane foam upholstered with fire retardent fabric tapestry and the back shall be made of PU Foam inserted frame of 19x2mm CR tube support by nylon belt for swinging comfort. The chair shall have a seat sliding mechanism. The armrest shall be made of PU having Cup holder. All metal components shall be powder coated in black colour with min 40 micron. The grouting plate shall be welded having the size 125mmx305mm x 4mm thick. The Seat size shall be 470 plus 10mm (W) x 440 plus 10mm (D) and back size shall be 760 plus 10mm (H) from seat x 465 plus 10mm(W) and overall height = 1060 plus 10mm (Make Geeken) Approved by Client.

Supply and erection of automatic three phase street light controller with time switch operation ON and OFF, setting upto 24 hours, complete with timelite 65 amp. 3 pole 230 V analog time switch contractor and MS power coated enclosure of suitable size. The work will be complete in all respect including making necessary connection, earthing nuts and bolts and other petty material to complete the job. (3 QT)

Supply of PVC/ XLPE insulated (Heavy Duty) Electrical cables for working voltage upto 1100 volt to IS: 1554 (PART-1) with Aluminium Conductor- ISI Marked Power Cable- Aluminium Conductor (95 sqmm 3 core armoured as per requirment). Make as per approved brand list of HPHC

Supply, Installation, Testing and Commissioning of 11 KV HT Panel having 1 No. VCB as Incomer, 03Nos. VCBs as Outgoings (4 Panel Board), as per following Technical Specifications , 630A, SC-18.4 KA FOR 1 SEC `VCB-Indoor Type(MDO) Horizontal Draw out Type, Motorized Spring Charge Manually Operated Vacuum circuit Breaker as per IEC 62271-100/200/IS 13118 .12 KV ,Isc-18.4 KA for 3 Sec ,Break trip free breaker with SPMX mechanism, mounted on a truck carriage ,complete with self contained operated fully interlocked rack in and rack out mechanism. Mechanism is suitable for 110 V DC Spring release coil ,shunt trip coil and auxiliary switch 6NO plus 6NC Switch 630A Incoming: 1 No. Outgoing: 3 No.` CT /PT Details : `Current Transformer: Indoor Single Phase Cast Resin Ratio 100/1-1A, Core-1 : 15 VA ,5P10 18.4KA- For IDMT Core-2 : 15 VA, CL-1 For Metering Incoming: 3 No. `Current Transformer: Indoor Single Phase Cast Resin Ratio 60/30/5-5A, Core-1 : 15 VA ,5P10 18.4KA- For IDMT Core-2 : 15 VA, CL-1 For Metering 40/5A Outgoing: 9 No. Potential Transformer: Indoor Single Phase Cast Resin Ratio: 11000/v3/110/v3/110/v3 V, Core-1: 100 VA, Class: 0.5 S/0.2 S, Incoming: 3 No.` `CB 2A SP for PT secondary 110V AC supply tapping Incoming: 3 No.` Relays : `3OC plus 1EF (50, 51, 50N, 51N) Numerical Type Protection Relay with TCS Incoming: 1 No. Outgoing: 3 No.` `Under and Over Voltage Relay Incoming: 1 No. `Master trip relay Incoming: 1 No. Outgoing: 3 No.` `Aux. Relays for TR Protections Outgoing: 6 No.` Meters : `Ammeter with SS Analog/Digital Incoming: 1 No. Outgoing: 3 No.` `Voltmeter with SS Analog/Digital Incoming: 1 No. `Multi Function Meter Incoming: 1 No. Outgoing: 3 No.` Breaker Panel Indication Lamps : `Breaker On- Red / Off - Green /Auto Trip - Amber / Trip Circuit Healthy - White / Spring Charged - Blue. Incoming: 1 No. Outgoing: 3 No.` `R, Y, B, Phase Indicators Incoming: 1 No. Outgoing: 3 No.` Switches and Accessories : `Control MCB 6A DP for AC and DC Circuits Incoming: 6 No. Outgoing: 18 No.` `Space Heater with thermostat and ON - OFF Toggle switch Incoming: 1 No. Outgoing: 3 No.` `Light and AC 3 Pin Socket Incoming: 1 No. Outgoing: 3 No.` `Alarm Hooter Assembly Incoming: 1 No. Outgoing: 3 No.` `TNC Switch (16 A) Incoming: 1 No. Outgoing: 3 No.` `Emergency Push Button Incoming: 1 No. Outgoing: 3 No.` `Control Wiring Incoming: 1 No. Outgoing: 3 No.` `All Hardware Incoming: 1 No. Outgoing: 3 No.` `6 Window Annunciator Incoming: 1 No. Outgoing: 3 No.` `HT Danger Plate Incoming: 1 No. Outgoing: 3 No.` Bus Bar `Earth Bus Bar 40 X 5 CU Incoming: 1 No. Outgoing: 3 No.` `Main Phase Bus Bar -1X60X10 mm Copper Incoming: 1 No. Outgoing: 3 No.` Panel Enclosure `Metering Box Incoming: 1 No. Outgoing: 3 No.`