Gurugram University Tender

Providing & fixing of Office Table : Providing and fixing table with side drawer & storage in Office as per layout •( 4'-0"x2'-6"+3'-0"x1'-6'') 2'-6". Design & shape Rectangular and taper inside at both side ends Table Top Material * 2 MDF batons with natural veneer * combination marine ply and corian with polyester coated profiled decorative venner on top side with backing laminate on bottom * combination of MDF particle board and solid wood with top venner face coated with clear lacquer * MDF and venner with PU finish having scratch resistance of 2H * MDF board as per IS: 12406 with pigmented PU coating on both sides * MDF with high grade membrane finish & balancing laminate on unexposed face * MDF with venner coating with high gloss polyester finish •Table Top of 25mm and front, side, back panel and drawer etc made of 18mm thick waterproof ISI Marked grade-1 MDF having laminate on both side as per the choice of buyer. The Table top have to designed in elevation pattern. Under Structure Of Main Table Gable end modesty panel With Aluminum anodized access flap (for electrical provision) Gable End Material * 2 MDF batons with natural veneer * Combination of MDF particle board and solid wood with top venner face coated with clear lacquer * MDF and venner with PU finish having scratch resistance of 2H * MDF board as per IS: 12406 with pigmented PU coating on both sides * Pre-laminated MDF board Modesty Panel Material * 2 MDF batons with natural veneer * MDF and venner with PU finish having scratch resistance of 2H * MDF board as per IS: 12406 with pigmented PU coating on both sides * Prelaminated MDF board (with all exposed edges sealed with 2mm PVC edge banding tape and all unexposed edges sealed with 0.6mm edge banding tape pressed at 200 degree C with hot melt glue on special) • PVC Edge Bending tape is to be provided on all visible sides i.e. Edges of boards/laminate duly polished in desired finished. • Storage unit having 3 drawer in each unit, total 2 storage unit must Size Of Drawers ± 2 Mm * 162 mm (H) x 640 mm (D) x 480 mm (W) * 243 mm (H) x 640 mm (D) x 480 mm (W) •Channels will be provided in keyboard tray and drawers of the storage unit. •Provision for CPU, keyboard along with wire cable gormment on table Top. • Complete in all respect with the prior Approval of Engineer In charge. make Board-Action Tessa, Century, Green .; Channel -Hettich, Hafley with prior approval of EIC

Low Ht. Storage Cabinet 4'-0"x3'-0"x1'-6"(Deep) size Top of 25mm and front, side, back panel and drawer etc made of 18mm thick waterproof ISI Marked grade-1 MDF having laminate on both side as per the choice of buyer.Single Partition to divide the cabinet in 2 parts 22Inch section each. All Plain Sides Of The Top Edge Banded With 2 Mm Thick PVC Tape With The Help Of Hot Melt Glue. ISI Marked, double layer MDF Board conforming to Grade SBG II of IS 12406/2003 laminated with 0.6-0.8 mm thick lamination conforming to IS 2046/1995 and balancing lamination of 0.5 mm thick on the back side. Melamine Chip Board (for body panels – door - side panel - drawer components) and Prelaminated board (for body back and drawer bottom) Each compartment provided with storage shelf.Complete in all respect with the prior Approval of Engineer In charge . make Board-Action Tessa, Century, Green; Channel- Hettich, Hafley with prior approval of EIC .

Revolving High Back Chair (with Headrest) as per following specification. : The seat is made up of insert moulded Polyurethane Foam upholstered with foam laminated mesh fabric. The insert moulded foam is assembled over a load bearing plastic seat cover. The back is made up of two piece injection moulded frame. The inner frame is upholstered with mesh fabric and mounted on the main assembly. The back has adjustable lumbar support for achieving comfortable seating posture. Average size (+5cm) Sub Assembly Seat size = 52.5 cm Width, 51 cm Depth. Sub Assembly Back size= 48.5 cm Max Width, 62 cm Ht. Effective Back Ht from Seat = 57 cm The polyurethane foam for seat is moulded with density = 75 ±4 kg/m3 and Hardness = 34 ± 4. The armrest top is injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest. The armrest height is adjustable up to 4-5cm in 3 steps & width adjustable. Arm Top Out to Out Dim = 62 to 65 cm, Arm Top Centre to Centre Dim = 53 to 56 cm. The mechanism is designed with the following features: - 360 degrees revolving type - Single point control - Front pivot for tilt 5 with feet resting on ground ensuring more comfort - Tilt tension adjustment - 3position locking with anti shock feature.Spine bracket is made of Aluminium diecast piece connecting back with mechanism.The pneumatic height adjustment has an adjustment of 8.5(+2) cm. Pedestal is made of Die cast Aluminium fitted with 5 nos. twin wheel castors castor wheel dia. 6.0 + 1cm). The pedestal have to be 65 + 2cm. Pitch center dia. (71.0 cm with castors) + 3cm.The twin wheel castors are injection moulded in Nylon. Brand : Geeken GA 570 (Syncro Tilt), Godrej,Durian with prior approval of EIC.