Gurugram Metropolitan Development Authority Tender
If you want to inquire about any e-tender the Haryana government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Haryana tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Haryana etender you're looking for. Read further to learn how to search and bid for etender Haryana.
Costs
EMD
₹ 8,04,618Document Cost
₹ 1,180Tender Fee
₹ 1,180
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_HRY_377487_1Bid Award Id
ViewTender No
2024B1B401B9 18A5 4F7E 9391 A687058CF8A9720001Tender Authority
Gurugram Metropolitan Development Authority ViewPurchaser Address
-Website
http://https://haryana.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
NS Item -Supplying, installing and testing of UPVC pipe (heavy duty) with 6 mm thick nitrile rubber insulation with protective coating as per the approved shop drawings and
specifications. Upto satisfaction of engineer incharge. 32 DIA.
80
-
-
NS Item -Design, manufacture, supply, installation, testing and commissioning of the following cubicle type, dead front, sheet steel, wall mounted control panels, including anchoring into the wall, wiring terminating into MCCB and copper earthing, in each panel shall be provided by the electrical contractor. Power and Control and panel cable with earthing in GI Cable tray from panel to motor shall be included in the cost. Upto satisfaction of engineer incharge.
1
-
-
NS Item -Supplying, Installing, testing and commissioning of air-cooled split AC Cassette unit, inverter type atleast 3 star along with indoor/ outdoor units, controls, copper piping,
uPVC condensate drain piping,including fully charged with refrigerant R32 to outdoor unit and all running refrigerant pipe as per detail given in drawing, valves and closed cell nitrile rubber insulation suitable to operate on 230 Volts 50 Hz AC supply etc. Quoted price shall include cost of wireless remote controller, wiring, control cable , MS stand for placing
outdoor unit with rubber pad isolator and earthing. Unit shall be provided with auto timer setting, complete as per technical specifications and tender drawings. The length of refrigerant pipe and drain pipe shall be considered as per drawings or site whichever is stringent. The unit shall be compete in all respect as stated. Upto satisfaction of engineer incharge...
8
-
-
NS Item -Supplying, Installing, testing and commissioning of air-cooled split AC Cassette unit, inverter type atleast 3 star along with indoor/ outdoor units, controls, copper piping,
uPVC condensate drain piping,including fully charged with refrigerant R32 to outdoor unit and all running refrigerant pipe as per detail given in drawing, valves and closed cell
nitrile rubber insulation suitable to operate on 230 Volts 50 Hz AC supply etc. Quoted price shall include cost of wireless remote controller, wiring, control cable , MS stand for placing
outdoor unit with rubber pad isolator and earthing. Unit shall be provided with auto timer setting, complete as per technical specifications and tender drawings. The length of refrigerant pipe and drain pipe shall be considered as per drawings or site whichever is stringent. The unit shall be compete in all respect as stated. Upto satisfaction of engineer incharge..
20
-
-
NS Item -Supplying, Installing, testing and commissioning of air-cooled split AC Cassette unit, inverter type atleast 3 star along with indoor/ outdoor units, controls, copper piping,
uPVC condensate drain piping,including fully charged with refrigerant R32 to outdoor unit and all running refrigerant pipe as per detail given in drawing, valves and closed cell
nitrile rubber insulation suitable to operate on 230 Volts 50 Hz AC supply etc. Quoted price shall include cost of wireless remote controller, wiring, control cable , MS stand for placing
outdoor unit with rubber pad isolator and earthing. Unit shall be provided with auto timer setting, complete as per technical specifications and tender drawings. The length of refrigerant pipe and drain pipe shall be considered as per drawings or site whichever is stringent. The unit shall be compete in all respect as stated. Upto satisfaction of engineer incharge.
20
-
-
NS Item -Supply, installation, testing and commissioning of factory fabricated double Skinned cabinet type fans section made out of extruded aluminium section with 1.0 mm preplasticized
/ pre-coated Galvanised steel sheet with DIDW blower, blower section and TEFC motor suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply with motor and
belt drive package. The fan Motor shall be of efficiency class IE3 . The blower should be AMCA Certified for air performance and sound rating and should be selected for maximum efficiency. Upto satisfaction of engineer incharge.
1
-
-
NS Item -Supplying and fixing Cable End Box (Loose Wire
Box) suitable for following single pole and neutral, sheet steel,
MCB distribution board, 240 Volts, on surface/ recess,
complete with testing and commissioning etc. as required.
For 14 way, Double door SPN MCBDB
1
-
-
NS Item -Supplying and fixing Cable End Box (Loose Wire
Box) suitable for following triple pole and neutral, sheet steel,
MCB distribution board, 415 Volts, on surface/ recess,
complete with testing and commissioning etc.as required.
For 6 way, Double door TPN MCBDB
1
-
-
NS Item -Supplying and fixing Cable End Box (Loose Wire
Box) suitable for following triple pole and neutral, sheet steel,
MCB distribution board, 415 Volts, on surface/ recess,
complete with testing and commissioning etc.as required.
For 8 way, Double door TPN MCBDB
6
-
-
NS Item -Supplying and fixing Cable End Box (Loose Wire
Box) suitable for triple pole and neutral, sheet steel, Vertical
MCB distribution board, 415 Volts, on surface/ recess,
complete with testing and commissioning etc. as required.
1
-
-
NS Item -Laying and fixing of one number PVC insulated and
PVC sheathed / XLPE power cable of 1.1 KV grade of
following size on cable tray as required.
Upto 35 sq. mm (clamped with 1mm thick saddle)
710
-
-
NS Item -Laying and fixing of one number PVC insulated and
PVC sheathed / XLPE power cable of 1.1 KV grade of
following size on cable tray as required.
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
MS flat clamp)
145
-
-
NS Item -Laying and fixing of one number PVC insulated and
PVC sheathed / XLPE power cable of 1.1 KV grade of
following size on cable tray as required.
Above 95 sq. mm and upto 185 sq. mm (clamped with
25/40x3mm MS flat clamp)
30
-
-
NS Item -Supplying and making end termination with brass
compression gland and aluminium lugs for following size of
PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1 KV grade as required.
3.5 core 185 sq. mm Al arm.
2
-
-
NS Item -Supplying and making end termination with brass
compression gland and aluminium lugs for following size of
PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1 KV grade as required.
3.5 core 150 sq. mm Al arm.
2
-
-
NS Item -Supplying and making end termination with brass
compression gland and aluminium lugs for following size of
PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1 KV grade as required.
3.5 core 95 sq. mm Al arm.
2
-
-
NS Item -Supplying and making end termination with brass
compression gland and aluminium lugs for following size of
PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1 KV grade as required.
3.5 core 50 sq. mm Al arm.
10
-
-
NS Item -Supplying and making end termination with brass
compression gland and aluminium lugs for following size of
PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1 KV grade as required.
4 core 25 sq. mm Al arm.
12
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays with perforation
not more than 17.5%, in convenient sections, joined with
connectors, suspended from the ceiling with M.S. suspenders
including bolts and nuts, painting suspenders etc as required.
150 mm width X 50 mm depth X 1.6 mm thickness
70
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays with perforation
not more than 17.5%, in convenient sections, joined with
connectors, suspended from the ceiling with M.S. suspenders
including bolts and nuts, painting suspenders etc as required.
450 mm width X 50 mm depth X 2.0 mm thickness
100
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays with perforation
not more than 17.5%, in convenient sections, joined with
connectors, suspended from the ceiling with M.S. suspenders
including bolts and nuts, painting suspenders etc as required.
600 mm width X 50 mm depth X 2.0 mm thickness
25
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays with perforation
not more than 17.5%, in convenient sections, joined with
connectors, suspended from the ceiling with M.S. suspenders
including bolts and nuts, painting suspenders etc as required.
750 mm width X 75 mm depth X 2.0 mm thickness
25
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays bends with
perforation not more than 17.5%,, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting suspenders etc as required.
150 mm width X 50 mm depth X 1.6 mm thickness
10
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays bends with
perforation not more than 17.5%,, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting suspenders etc as required.
300 mm width X 50 mm depth X 1.6 mm thickness
6
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays bends with
perforation not more than 17.5%,, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting suspenders etc as required.
450 mm width X 50 mm depth X 2.0 mm thickness
4
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays bends with
perforation not more than 17.5%,, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting suspenders etc as required.
600 mm width X 50 mm depth X 2.0 mm thickness
2
-
-
NS Item -Supplying and installing following size of perforated
painted with powder coating M.S. cable trays bends with
perforation not more than 17.5%,, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting suspenders etc as required.
750 mm width X 75 mm depth X 2.0 mm thickness
2
-
-
NS Item -`Supplying and installing following size of perforated
painted with powder coating M.S. cable trays Tee with
perforation not more than 17.5%, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting
suspenders etc as required.`
150 mm width X 50 mm depth X 1.6 mm thickness
6
-
-
NS Item -`Supplying and installing following size of perforated
painted with powder coating M.S. cable trays Tee with
perforation not more than 17.5%, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting
suspenders etc as required.`
300 mm width X 50 mm depth X 1.6 mm thickness
6
-
-
NS Item -`Supplying and installing following size of perforated
painted with powder coating M.S. cable trays Tee with
perforation not more than 17.5%, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting
suspenders etc as required.`
450 mm width X 50 mm depth X 2.0 mm thickness
4
-
-
NS Item -`Supplying and installing following size of perforated
painted with powder coating M.S. cable trays Tee with
perforation not more than 17.5%, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting
suspenders etc as required.`
600 mm width X 50 mm depth X 2.0 mm thickness
2
-
-
NS Item -`Supplying and installing following size of perforated
painted with powder coating M.S. cable trays Tee with
perforation not more than 17.5%, joined with connectors,
suspended from the ceiling with M.S. suspenders including
bolts and nuts, painting
suspenders etc as required.`
750 mm width X 75 mm depth X 2.0 mm thickness
1
-
-
NS Item -Supplying and installing following size of perforated
Hot Dipped Galvanised Iron cable tray (Galvanisation
thickness not less than 50 microns) with perforation not more
than 17.5%, in convenient sections, joined with connectors,
suspended from the ceiling with G.I. suspenders including G.I.
bolts and nuts, etc. as required.
150 mm width X 50 mm depth X 1.6 mm thickness
100
-
-
NS Item -Supplying and installing following size of perforated
Hot Dipped Galvanised Iron cable tray (Galvanisation
thickness not less than 50 microns) with perforation not more
than 17.5%, in convenient sections, joined with connectors,
suspended from the ceiling with G.I. suspenders including G.I.
bolts and nuts, etc. as required.
300 mm width X 50 mm depth X 1.6 mm thickness
75
-
-
NS Item -Supplying and installing following size of perforated
Hot Dipped Galvanised Iron cable tray `bends` (galvanisation
not less than 50 microns) with perforation not more than
17.5%, in convenient sections, joined with connectors,
suspended from the ceiling with G.I. suspenders including G.I.
bolts and nuts, etc. as required.
150 mm width X 50 mm depth X 1.6 mm thickness
5
-
-
NS Item -Supplying and installing following size of perforated
Hot Dipped Galvanised Iron cable tray `bends` (galvanisation
not less than 50 microns) with perforation not more than
17.5%, in convenient sections, joined with connectors,
suspended from the ceiling with G.I. suspenders including G.I.
bolts and nuts, etc. as required.
300 mm width X 50 mm depth X 1.6 mm thickness
5
-
-
NS Item -Supplying and installing following size of perforated
Hot Dipped Galvanised Iron cable tray `Tee` (galvanisation
not less than 50 microns) with perforation not more than
17.5%, in convenient sections, joined with connectors,
suspended from the ceiling with G.I. suspenders including G.I.
bolts and nuts, etc. as required.
150 mm width X 50 mm depth X 1.6 mm thickness
5
-
-
NS Item -Supplying and installing following size of perforated
Hot Dipped Galvanised Iron cable tray `Tee` (galvanisation
not less than 50 microns) with perforation not more than
17.5%, in convenient sections, joined with connectors,
suspended from the ceiling with G.I. suspenders including G.I.
bolts and nuts, etc. as required.
300 mm width X 50 mm depth X 2.0 mm thickness
5
-
-
NS Item -Providing, laying and fixing following dia RCC pipe
NP2 class (light duty) in ground complete with RCC collars,
jointing with cement mortar 1:2 (1 cement : 2 fine sand)
including trenching (75 cm deep) and refilling etc as required.
300mm dia
20
-
-
NS Item -Providing, laying and fixing following dia RCC pipe
NP2 class (light duty) in ground complete with RCC collars,
jointing with cement mortar 1:2 (1 cement : 2 fine sand)
including trenching (75 cm deep) and refilling etc as required.
150mm dia
10
-
-
NS Item -Supply, Testing and Commissioning, fixing of
following bare Copper / GI tapes / wires including all
necessary fixing accessories, insulators and effecting
connections as per specifications.
Providing and fixing 25 mm X 5 mm Copper strip on surface or
in recess for connections etc. as required.
60
-
-
NS Item -Supply, Testing and Commissioning, fixing of
following bare Copper / GI tapes / wires including all
necessary fixing accessories, insulators and effecting
connections as per specifications.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in
recess for connections etc. as required.
100
-
-
NS Item -Supply, Testing and Commissioning, fixing of
following bare Copper / GI tapes / wires including all
necessary fixing accessories, insulators and effecting
connections as per specifications.
Providing and fixing 6 SWG dia G.I. wire on surface or in
recess for loop earthing along with existing surface/ recessed
conduit/ submain wiring/ cable as required.
50
-
-
NS Item -Earthing with G.I. earth plate 600 mm X 600 mm X 6
mm thick including accessories, and providing masonry
enclosure with cover plate having locking arrangement and
watering pipe of 2.7 metre long etc. with charcoal/ coke and
salt as required.
6
-
-
NS Item -Earthing with copper earth plate 600 mm X 600 mm
X 3 mm hick including accessories, and providing masonry
enclosure with cover plate having locking arrangement and
watering pipe of 2.7 metre long etc. with charcoal/ coke and
salt as required.
4
-
-
NS Item -Supplying and fixing 20 A, 240 V, SPN Industrial
type socket outlet, with 2 pole and earth, metal enclosed plug
top alongwith 20 A `C` curve, SP, MCB, in sheet steel
enclosure, on surface or in recess, with chained metal cover
for the socket out let and complete with connections, testing
and commissioning etc. as required.
2
-
-
NS Item -Supplying and fixing two module stepped type
electronic fan regulator on the existing modular plate switch
box including connection but excluding modular plate etc. as
required.
5
-
-
NS Item -Supplying and fixing extra down rod of 10 cm length
G.I pipe,15mm dia, heavy gauge including painting etc. as
required.(Note-more than 5 cm length shall be rounded to the
nearest 10 cm and 5 cm or less shall be ignored)
5
-
-
NS Item -Supply, Installation, Testing and Commissioning of
1200 mm sweep, BBEE 5 star rated, ceiling fan with Brush
Less Direct Current (BLDC) Motor, class of insulation: B, 3
nos. blades, 45 cm long down rod, 2nos. canopies, shackle
kit, safety rope, copper winding, Power Factor not less than
0.9, Service Value (CM/M/W) minimum 6.00, Air delivery
minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-
2019), THD less than 10%, remote or electronic regulator unit
for speed control and all remaining accessories including
safety pin, nut bolts, washers, temperature rise=75 degree C
(max.), insulation resistance more than 2 mega ohm, suitable
for 230 V, 50 Hz, single phase AC Supply, earthing etc.
complete as required.
5
-
-
NS Item -`Design, fabrication, assembling, wiring and supply,
installation, testing and commissioning of Main LT Panels
fabricated out of (load bearing member of 2mm and non load
bearing member 1.6 mm thick) CRCA sheet steel in cubicle
compartmentised modular 4b construction, free standing floor
mounted with bottom cable entry, dust and vermin proof with
reinforcement of suitable size angle iron, channel, `T’ sections
and / or flats wherever necessary. 3 mm thick cable gland
plates shall be provided on top as well as at the bottom of the
panels. Panels shall be treated with all anticorrosive process
before powder coating as per specifications and final
approved shade. 2 Nos. earthing terminals shall be provided
for all distrtibution panels. Panels shall be suitable for 415V, 3
phase, 4 wire, 50 HZ supply system. Lifting hooks shall also
be provided in case of large panels. Approval shall be taken
for each panel in the form of shop drawings before
fabrication. Galvanised hardwares with zinc passivation shall
be used in fabrication of panels. Upto satisfaction of engineer
incharge.
40 kVAR Capacitor Panel`
1
-
-
NS Item -`Design, fabrication, assembling, wiring and supply,
installation, testing and commissioning of Main LT Panels
fabricated out of (load bearing member of 2mm and non load
bearing member 1.6 mm thick) CRCA sheet steel in cubicle
compartmentised modular 4b construction, free standing floor
mounted with bottom cable entry, dust and vermin proof with
reinforcement of suitable size angle iron, channel, `T’ sections
and / or flats wherever necessary. 3 mm thick cable gland
plates shall be provided on top as well as at the bottom of the
panels. Panels shall be treated with all anticorrosive process
before powder coating as per specifications and final
approved shade. 2 Nos. earthing terminals shall be provided
for all distrtibution panels. Panels shall be suitable for 415V, 3
phase, 4 wire, 50 HZ supply system. Lifting hooks shall also
be provided in case of large panels. Approval shall be taken
for each panel in the form of shop drawings before
fabrication. Galvanised hardwares with zinc passivation shall
be used in fabrication of panels. Upto satisfaction of engineer
incharge.
Main LT Panel`
1
-
-
NS Item -`Design, fabrication, assembling, wiring and supply,
installation, testing and commissioning of LT Panel,
Distribution Panels, fabricated out of (load bearing member of
2mm and non load bearing member 1.6 mm thick) CRCA
sheet steel in cubicle compartmentised modular 3b
construction, free standing floor mounted with bottom cable
entry, dust and vermin proof with reinforcement of suitable
size angle iron, channel, `T’ sections and / or flats wherever
necessary. 3 mm thick cable gland plates shall be provided on
top as well as at the bottom of the panels. Panels shall be
treated with all anticorrosive process before powder coating
as per specifications and final approved shade. 2 Nos.
earthing terminals shall be provided for all distrtibution
panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50
HZ supply system. Lifting hooks shall also be provided in
case of large panels. Approval shall be taken for each panel in
the form of shop drawings before fabrication. Galvanised
hardwares with zinc passivation shall be used in fabrication of
panels. Upto satisfaction of engineer incharge.
MDB - 2 (Library Building) ( Electrical Niche) (Upper Side)`
1
-
-
NS Item -`Design, fabrication, assembling, wiring and supply,
installation, testing and commissioning of LT Panel,
Distribution Panels, fabricated out of (load bearing member of
2mm and non load bearing member 1.6 mm thick) CRCA
sheet steel in cubicle compartmentised modular 3b
construction, free standing floor mounted with bottom cable
entry, dust and vermin proof with reinforcement of suitable
size angle iron, channel, `T’ sections and / or flats wherever
necessary. 3 mm thick cable gland plates shall be provided on
top as well as at the bottom of the panels. Panels shall be
treated with all anticorrosive process before powder coating
as per specifications and final approved shade. 2 Nos.
earthing terminals shall be provided for all distrtibution
panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50
HZ supply system. Lifting hooks shall also be provided in
case of large panels. Approval shall be taken for each panel in
the form of shop drawings before fabrication. Galvanised
hardwares with zinc passivation shall be used in fabrication of
panels. Upto satisfaction of engineer incharge.
MDB - 3 (Library Building) ( Electrical Niche) (Lower Side)`
1
-
-
NS Item -`Design, fabrication, assembling, wiring and supply,
installation, testing and commissioning of LT Panel,
Distribution Panels, fabricated out of (load bearing member of
2mm and non load bearing member 1.6 mm thick) CRCA
sheet steel in cubicle compartmentised modular 3b
construction, free standing floor mounted with bottom cable
entry, dust and vermin proof with reinforcement of suitable
size angle iron, channel, `T’ sections and / or flats wherever
necessary. 3 mm thick cable gland plates shall be provided on
top as well as at the bottom of the panels. Panels shall be
treated with all anticorrosive process before powder coating
as per specifications and final approved shade. 2 Nos.
earthing terminals shall be provided for all distrtibution
panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50
HZ supply system. Lifting hooks shall also be provided in
case of large panels. Approval shall be taken for each panel in
the form of shop drawings before fabrication. Galvanised
hardwares with zinc passivation shall be used in fabrication of
panels. Upto satisfaction of engineer incharge.
MDB - U1 (UPS Panel) (CCTV Room)`
1
-
-
NS Item -`FRLS CABELS
Supplying of following 1100 volt grade XLPE insulated FRLS
sheathed Aluminium/Copper conductor armoured/Unarmored
cables as per specification complete in all respect as required
as per site conditions. Upto satisfaction of engineer incharge.
3.5 core 185 sq. mm Al arm.`
100
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
3.5 core 150 sq. mm Al arm.`
55
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
3.5 core 95 sq. mm Al arm.`
55
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
3.5 core 50 sq. mm Al arm.`
145
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
4 core 25 sq. mm Al arm.`
230
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
4 core 10 sq. mm. Cu arm.`
65
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
4 core 6 sq.mm Cu arm.`
225
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
3 core 4 sq.mm Cu arm.`
105
-
-
NS Item -Supplying of following 1100 volt grade XLPE
insulated FRLS sheathed Aluminium/Copper conductor
armoured/Unarmored cables as per specification complete in
all respect as required as per site conditions. Upto satisfaction
of engineer incharge.
1 core 6 sq.mm Cu Unarm. FRLS for UPS Connectivity`
85
-
-
NS Item -`Supplying and making Cable end termination of the
following XLPE insulated PVC sheathed Aluminium / copper
conductor armoured cables of 1100 volt grade including
supplying and fixing of bimettalic crimping lugs, double
compression glands with earthing testing and commissioning
complete in all respect as required as per site conditions. Upto
satisfaction of engineer incharge.
4 core 10 sq. mm. Cu arm.`
12
-
-
NS Item -`Supplying and making Cable end termination of the
following XLPE insulated PVC sheathed Aluminium / copper
conductor armoured cables of 1100 volt grade including
supplying and fixing of bimettalic crimping lugs, double
compression glands with earthing testing and commissioning
complete in all respect as required as per site conditions. Upto
satisfaction of engineer incharge.
4 core 6 sq.mm Cu arm.`
8
-
-
NS Item -`Supplying and making Cable end termination of the
following XLPE insulated PVC sheathed Aluminium / copper
conductor armoured cables of 1100 volt grade including
supplying and fixing of bimettalic crimping lugs, double
compression glands with earthing testing and commissioning
complete in all respect as required as per site conditions. Upto
satisfaction of engineer incharge.
3 core 4 sq.mm Cu arm.`
4
-
-
NS Item -`Supplying and making Cable end termination of the
following XLPE insulated PVC sheathed Aluminium / copper
conductor armoured cables of 1100 volt grade including
supplying and fixing of bimettalic crimping lugs, double
compression glands with earthing testing and commissioning
complete in all respect as required as per site conditions. Upto
satisfaction of engineer incharge.
1 core 6 sq.mm Cu Unarm. FRLS for UPS Connectivity`
16
-
-
NS Item -Laying of one number PVC insulated and PVC
sheathed / XLPE power cable of 1.1 KV grade of following
size direct in ground including excavation and refilling the
trench etc as required, but excluding sand cushioning and
protective covering.
Above 95 sq. mm and upto 185 sq. mm (clamped with
40x3mm MS flat clamp)
210
-
-
NS Item -Supplying and fixing of following sizes of steel
conduit along with accessories in surface/recess including
painting in case of surface conduit, or cutting the wall and
making good the same in case of recessed conduit as
required.
25 mm
600
-
-
NS Item -Supplying and fixing of following sizes of steel
conduit along with accessories in surface/recess including
painting in case of surface conduit, or cutting the wall and
making good the same in case of recessed conduit as
required.
32 mm
100
-
-
NS Item -Supplying and drawing co-axial TV cable RG-6
grade, 0.7 mm solid copper conductor PE insulated, shielded
with fine tinned copper braid and protected with PVC sheath
in the existing surface/ recessed steel/ PVC conduit as
required. DSR 2022/ 1.19
90
-
-
NS Item -Supply, installation, testing and commissioning of 10
kVA UPS in N configuration, 3 phase (415 V plus 15%) Volts
input and 3 phase output (440 V plus 1%), 50 Hz, 100%
IGBT inverter and converter, Input harmonic Current THD 3%
typical at 100% load, 6% maximum at 50% load and 90 min
battery backup for each UPS along with battery cabinet
complete in all respect including supporting steel structure for
UPS and Battery as required. Quoted price shall be inclusive
of approved rating single core copper conductor cable
connecting UPS and batteries. Upto satisfaction of engineer
incharge. (For Emergency Lighting)
1
-
-
NS Item -Feeder Pillar (For External Landscape lighting) IP 55 for outdoor Protection Incomer 63 Amps 4 pole MCB, Photocell Sensor Bus Bars 100 Amps TPN Aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set Outgoing 40 Amps 4 pole MCB incomer with 40 Amps TP contactor 0-24 hours timer auto / manual and outgoings including 10 No. 10/16/20 Amps SP MCB with 3 Nos. 32 Amps DP RCCB’s of 30 mA leakage current with separate neutral link of each phase- 1 set (50%) 40 Amps DP MCB - 4 set 63 Amps 4 Pole MCB - 4 set Feeder Pillar for external / landscape lighting as described above upto satisfaction of engineer incharge.`
1
-
-
NS Item -Providing and fixing factory made precast RCC
perforated drain covers, having concrete of strength not less
than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm
dia four nos longitudinal and 9 nos cross sectional T.M.T.
hoop bars, including providing 50 mm dia perforations @ 100
to 125 mm c/c, including providing edge binding with M.S.
flats of size 50 mm x 1.6 mm complete, all as per direction of
Engineer-in-charge.
60
-
-
NS Item -Supplying, installation, testing and commissioning of
microprocessor based intelligent addressable main fire alarm
panel, central processing unit with the following loop modules
and capable of supporting not less than 240 devices (including
detectors) and minimum 120 detectors per loop and loop
length up to 2 km, network communication card, minimum 320
character graphics/ LCD display with touch screen or other
keypad and minimum 4000 events history log in the non
volatile memory (EPROM), power supply unit (230± 5% V, 50
hz), 48 hrs back-up with 24 volt sealed maintenance free
batteries with automatic charger. The panel shall have facility
to connect printer to printout log and facility to have seamless
integration with analog/digital voice evacuation system (which
is part of the schedule of work under SH: PA System) and
shall be complete with all accessories . The panel shall be
compatible for IBMS system with open protocol BACnet/
Modbus over IP complete as per specifications.
Two Loop Panel
1
-
-
NS Item -Supplying, installation, testing and commissioning of
intelligent analog addressable photothermal detector complete
with mounting base complete as required.
70
-
-
NS Item -Supplying, installation, testing and commissioning of
fault isolator complete with base as required.
10
-
-
NS Item -Supplying, installation, testing and commissioning of
intelligent addressable thermal detector with rate of rise cum
fixed temperature thermistor complete with base as required.
5
-
-
NS Item -Supplying, installation, testing and commissioning of
addressable fire control module complete as required.
25
-
-
NS Item -Supplying, installation, testing and commissioning of
addressable manual call point complete as required.
5
-
-
NS Item -Supplying, installation, testing and commissioning of
addressable horn cum strobe complete as required.
5
-
-
NS Item -Supplying, installation, testing and commissioning of
fire fighter telephone handset complete as required.
1
-
-
NS Item -Supplying, installation, testing and commissioning of
fire fighter phone jack complete as required.
5
-
-
NS Item -Supplying, installation, testing and commissioning of
1.5/3/6W metal box ceiling/wall speaker complete as required.
70
-
-
NS Item -Supplying and laying of 2x1.5 sqmm fire survival
armoured cable, 600/1000V rated with annealed copper
conductor having glass mica fire barrier tape covered by an
extruded layer of Cross Linkable Ethylene Propylene Rubber
(EPR) Insulation and LSZH inner bedding, steel wire
armouring and LSZH outer sheath complete as required.
900
-
-
NS Item -Supplying and fixing 25 mm dia MS flexible pipe with
PVC coating along with all ancillaries and accessories like
coupler etc. as required.
50
-
-
NS Item -Supplying, installation, testing and commissioning of
6 Zone voice alarm controller with USB, MP3, player
(inlcuding 6 Zone button paging station) with seamless
integration facility with Main Fire Alarm panel for voice
evacuation complete as required.
1
-
-
NS Item -Supplying, installation, testing and commissioning of
digital audio amplifier 75 Watt, 25V rms operating at 240 Volts
AC supply complete as required.
3
-
-
NS Item -Supplying, installation, testing and commissioning of
Voice Command Keypad 6 zone, with microphone assembly
complete as required.
1
-
-
NS Item -Supplying, installation, testing and commissioning of
repeater panel wih 320 character/ Touch screen LCD display
with inbuilt reset, acknowledge and silence switches complete
as required.
1
-
-
NS Item -Supplying, installation, testing and commissioning of
Electric driven Main Fire Pump suitable for automatic
operation and consisting of following, complete in all respects,
as required:
Horizontal type, centrifugal, split casing pump of cast iron
body and bronze impeller with stainless steel shaft,
mechanical seal conforming to IS 1520.
Suitable HP Squirrel cage induction motor, TEFC,
synchronous speed 1500 RPM, suitable for operation on 415
volts, 3 phase 50 Hz, AC supply with IP 55 protection for
enclosure, horizontal foot mounted type with Class-`F`
insulation, conforming to IS-325.
M.S. fabricated Common base plate, coupling, coupling
guard, foundation bolts etc. as required
Suitable cement concrete foundation duly plastered with anti
vibration pads.
1620 lpm at 56 m Head (Hydrant and Sprinkler Pump)
1
-
-
NS Item -Supplying, installation, testing and commissioning of
diesel engine driven main fire pump suitable for automatic
operation and consisting of following, complete in all respects,
as required : (Diesel Driven Pump)
Horizontal type, multistage, centrifugal pump of cast of iron
body and bronze impeller with stainless steel shaft,
mechanical seal conforming to IS 1520.
Suitable HP, 1500 RPM water cooled with radiator, diesel
engine conforming to relevant IS standard complete with auto
starting mechanism, 12 /24 volts electric starting equipment,
diesel tank, exhaust pipe extended upto 10 m outside pump
house duly insulated with 50 mm thick glass wool with 1.0 mm
thick aluminium sheet cladding, residential silencer,
instruments and protection as per standard specification, stop
solenoid for auto stop in the event of fault with audio
indications, painted with post office red colour etc. as required.
M.S fabricated, common base plate, coupling, coupling guard,
foundation bolts etc. as required.
Suitable cement concrete foundation duly plastered and with
anti vibration pads.
1620 lpm at 56 m Head (Hydrant and Sprinkler Pump)
Note: * The head of the pump is selected in a manner so as to
give a minimum 3.5kgf/cm 2 pressure at the highest/farthest
point
1
-
-
NS Item -Supplying, installation, testing and commissioning of
electric driven pressurisation pump suitable for automatic
operation and consisting of following, complete in all respects,
as required : (Jockey Pump)
Horizontal type, multistage, centrifugal pump of cast iron body
and bronze impeller with stainless steel shaft, mechanical seal
conforming to IS : 1520.
Suitable HP squirell cage induction motor TEFC type suitable
for operation on 415 volts, 3 phase 50 Hz AC supply with IP
55 class of protection for enclosure, horizontal foot mounted
type with Class-`F` insulation, conforming to IS : 325.
M.S.fabricated Common base plate, coupling, coupling guard,
foundation bolts etc. as required.
Suitable cement concrete foundation duly plastered and with
anti vibration pads
180 lpm at 56 m Head (Hydrant and Sprinkler Pump)
1
-
-
NS Item -CONTROL PANELS
Fabrication, supply, Insallation testing and commissioning of
Electrical control panel of cubical construction, floor mounted
type, fabricated out of 2mm thick CRCA sheet,
compartmentalised with hinged lockable doors, dust and
vermin proof, powder coated of approved shade after 7 tank
treatment process, cable alley, inter connection with suitable
size copper conductor cable/solid copper strip, having
switchgears and accessories, mountings and internal wiring,
earth terminals, numbering etc. complete in all respect,
suitable for main fire pump, pressurisation pump and diesel
pump set complete as per CPWD specification with following
in coming and Outgoings, suitable for operation on 415V, 3
phase, 50Hz Ac Supply with enclosure protection class IP 42
as required :
INCOMING
250A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital
Voltmeter 0-500V with selector switch Ammeter (0-250 A) with
selector swtich and CTs etc.
LED type RYB phase indicating lamps, ON, OFF, trip
indicating lamps
Set of Copper Bus Bar 300Amps
OUTGOING
( Note : All outgoing feeders for pumps should have digital
Ammeter with selector switches, and LED type ON, OFF, trip
indicating lamps)
Main Fire Pump (Sprinkler and Hydrant)
125 Amp, 50kA TPN MCCB, Ics=100% Icu, with fully
automatic Star/Delta starter suitable for 60 hp pump with
overload protection, current sensing type single phase
preventor complete with all acceessories and internal wiring
required for automatic operation, selector switch for
local/remote, auto/manual/OFF operation.
Jockey Pump
63 Amp, 50kA TPN MCCB, Ics=100% Icu, with Suitable HP
fully automatic Star/Delta starter with overload protection,
current sensing type single phase preventor complete with all
acceessories and internal wiring required for automatic
operation, selector switch for local/remote, auto/manual/OFF
operation.
Diesel Engine Control
Control for diesel engine comprising -
Automatic/Manual selctor switch and 3 attempts starting
device, timers and relays as required, push buttons, start/stop
in manual mode
Indicating lamp for high/ Low Lub. Oil pressure, High Water
Temp and Engine on indication
Battery charger suitbale for 12V/24 V DC with boost and
trickle selector switch, 0-30 V DC volt meter, and 0-20 A DC
Ammeter
All standard relays and accessories for automatic operation of
diesel engine
System Controller
Designing, Supply, Installation, Testing and commissioning of
system controller to control operation of main electric fire
pump, diesel pump, Pressurization pump, in sequence as per
specification consisting of relays, timers. Sensors,
annunciation window for fault indication, complete as per
specification
1
-
-
NS Item -Providing laying, testing and commissioning of `C`
class heavy duty MS Pipe conforming to IS 1239 / 3589 i/c
fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets
etc. in ground including welding, excavation and providing
cement concrete blocks as supports, anticorrosive treatment
with coaltar / asphalt tape as per IS 10221, refilling the trench
etc. of following sizes complete as required
200 mm. dia (wall thickness = 6.3 mm)
10
-
-
NS Item -Providing laying, testing and commissioning of `C`
class heavy duty MS Pipe conforming to IS 1239 / 3589 i/c
fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets
etc. in ground including welding, excavation and providing
cement concrete blocks as supports, anticorrosive treatment
with coaltar / asphalt tape as per IS 10221, refilling the trench
etc. of following sizes complete as required
150 mm. Dia
15
-
-
NS Item -Providing, laying, testing and commissioning of `C`
class heavy duty MS pipe conforming to IS 3589/IS 1239
including Welding, fittings like elbows, tees, flanges, tapers,
nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling
with suitable clamp/support frame and painting with two or
more coats of synthetic enamel paint of required shade
complete as required :
80 mm dia
5
-
-
NS Item -Providing, laying, testing and commissioning of `C`
class heavy duty MS pipe conforming to IS 3589/IS 1239
including Welding, fittings like elbows, tees, flanges, tapers,
nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling
with suitable clamp/support frame and painting with two or
more coats of synthetic enamel paint of required shade
complete as required :
150 mm dia
35
-
-
NS Item -Providing, laying, testing and commissioning of `C`
class heavy duty MS pipe conforming to IS 3589/IS 1239
including Welding, fittings like elbows, tees, flanges, tapers,
nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling
with suitable clamp/support frame and painting with two or
more coats of synthetic enamel paint of required shade
complete as required :
150 mm dia (Vartical Riser)
20
-
-
NS Item -Supplying and fixing single headed internal hydrant
valve with instantaneous Gunmetal/Stainless Steel coupling of
63 mm dia with cast iron wheel ISI marked conforming to IS
5290 (Type -A) with blank Gunmetal/Stainless Steel cap and
chain as required :
Single headed Stainless Steel
2
-
-
NS Item -Supplying, fixing, testing and commissioning of
butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly
ISI marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
150 mm dia
5
-
-
NS Item -Supplying, fixing, testing and commissioning of
butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly
ISI marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
200 mm dia
1
-
-
NS Item -Providing, installation, testing and commissioning of
non-return valve of following sizes confirming to IS: 5312
complete with rubber gasket, GI bolts, nuts, washers etc.as
required :
80 mm dia
1
-
-
NS Item -Providing, installation, testing and commissioning of
non-return valve of following sizes confirming to IS: 5312
complete with rubber gasket, GI bolts, nuts, washers etc.as
required :
150 mm dia
2
-
-
NS Item -Providing, installation, testing and commissioning of
stainless steel Y-strainer fabricated out of 1.6 mm thick
stainless steel, Grade 304, sheet with 3 mm dia holes with
stainless steel flange.
200 mm dia
1
-
-
NS Item -Supplying and fixing 63 mm dia, 15 m long RRL
hose pipe with 63 mm dia male and female couplings duly
bound with GI wire, rivets etc. conforming to IS 636 (type-A)
as required :
Stainless Steel (Grade 304)
4
-
-
NS Item -Supplying and fixing first-aid Hose Reel with MS
construction spray painted in post office red, conforming to IS
884 complete with the following as required.
20 mm nominal internal dia water hose thermoplastic (Textile
reinforced) type -2 as per IS: 12585
20 mm nominal internal dia gun metal globe valve and nozzle.
Drum and brackets for fixing the equipmets on wall.
Connections from riser with 25 mm dia stop gun metal valve
and M.S. Pipe and socket.
30 Meters
2
-
-
NS Item -Supplying and fixing 63 mm dia gun metal short
branch pipe with 20 mm nominal internal diameter size nozzle
conforming to IS903 suitable for instantaneous connection to
interconnect hose pipe coupling as required
Stainless Steel (Grade 304)
2
-
-
NS Item -Supplying and fixing air vessel made of 250 mm dia,
8 mm thick MS sheet, 1200 mm in height with air release
valve on top and flanged connection to riser, drain
arrangement with 25 mm dia gun metal wheel valve with
required accessories, pressure gauge and painting with
synthetic enamel paint of approved shade as required.
1
-
-
NS Item -Providing, installation and Testing of CO2 Type Fire
Extinguisher, PESO approved Cylinder, filled inhouse with
CO2 gas with purity as per IS:15222, Aluminium Collar and
Valve Wheel, Metal lined rubber discharge hose, external PU
paint coating,UV resistant Vinyl Label, QR code, MMX CO2
4.5 Kg IS:15683 (WheelType) (Fire Rating 55B ), upto
satisfaction of engineer incharge.
6
-
-
NS Item -Providing, installation and Testing of Optima Stored
Pressure Type Fire Extinguisher, MS Body with Internal and
External Epoxy coating, Safety Release device on valve,
stainless Steel Safety Pin, UV resistant Vinyl Label, QR code.
ISI Marked, MMO MF 9 Ltr IS:15683 Stored Pressure (Fire
Rating 4A 233B ), upto satisfaction of engineer incharge.
6
-
-
NS Item -Providing, installation and Testing of Optima Stored
Pressure Type Fire Extinguisher, MS Body with Internal and
External Epoxy coating, Safety Release device on valve,
stainless Steel Safety Pin, UV resistant Vinyl Label, QR code.
ISI Marked, MMO ABC 9 Kg IS:15683 Stored Pressure (Fire
Rating 6A 144B ), upto satisfaction of engineer incharge.
4
-
-
NS Item -Supplying, installation, testing and commissioning of
addressable fire Monitor module complete as required., upto
satisfaction of engineer incharge.
5
-
-
NS Item -Supply Installation, testing and commissioning of
LED Recessed Downlighter having cut-out dia of 125mm(±
3mm) and lip to lip dia of 137mm (± 3mm) delivering
minimum system lumen output of 1500 lumens and system
wattage of 12.5W (±5%) and with a minimum system efficacy
of 105 lm/W (=120lm/W). The luminaire should have a colour
temperature of 6500°K, CRI=80 and R9=0 and SDCM=5. The
luminaire should have deep recessed COB light source with
UGR=19 and Shielding Angle of 38°. The luminaire shall have
the beam angle of 60° to 65°. The Driver shall have
THD=10% (@full Load) and PF = 0.95 (@full load). The
luminaire housing, heat sink and ring should made of pressure
die-cast aluminium. The luminaire should have faceted
reflector made of Spun Aluminum. Reflectors made of
Polycarbonate shall not be allowed. The fixture should comply
with the parameters as per IS10322. The luminaire shall have
impact resistance of IK02 and ingress protection of IP20. The
luminaire driver shall be of the same make/manufacturer as
that of LED luminaires. Luminaire manufacturer must have Inhouse
NABL accredited lab to conduct LM79, Type test as per
IS10322, `FAT` before dispatch as per IS 10322 and IK Test.
The successful bidder must submit the NABL accreditation
certificate for Luminaire manufacturer before supply of LED
luminaires for approval. The LED Luminaire and it`s driver
both should be BIS registered. Successful bidder shall submit
the following reports before supply of material for approvals
LM79 issued by NABL accredited lab, LM80 issued by LED
manufacturer, Type Test Certificate for luminaire as issued by
NABL accredited lab, BIS certificate for LED Luminaire and
Driver. Similar to above specs in Signify (Philips)/
Wipro//Havells or equivalent, upto satisfaction of engineer
incharge.
390
-
-
NS Item -Supply of Decorative Pendant LED Luminaire
delivering minimum system lumen of 5600 lm and the
luminaire shall be with system efficacy =70 lm / W and shall
be of 80W. Housing Extruded Aluminium Powder Coated,
having dimensions of 1200m dia and H75mm, IP20 , Opal
milky white diffuser. The operating CCT shall be 6500K with
CRI of =80. The luminaire shall have electronic driver with
input voltage range of 140 to 270V , THD = 10% (@full load)
and PF = 0.95 (@full load) , 30K hrs@ L70B50 @ 45 degree
ambient. The luminaire driver shall be of the same
make/manufacturer as that of LED luminaires. Luminaire
manufacturer must have In-house NABL accredited lab to
conduct LM79, Type test as per IS10322, `FAT` before
dispatch as per IS 10322 and IK Test. The successful bidder
must submit the NABL accreditation certificate for Luminaire
manufacturer before supply of LED luminaires for approval.
The LED Luminaire and it`s driver both should be BIS
registered. Successful bidder shall submit the following
reports before supply of material for approvals LM79 issued by
NABL accredited lab, LM80 issued by LED manufacturer,
Type Test Certificate for luminaire as issued by NABL
accredited lab, BIS certificate for LED Luminaire and
Driver.Similar to above specs in Signify (Philips)/
Wipro//Havells or equivalent, upto satisfaction of engineer
incharge.
10
-
-
NS Item -Supply of pendant luminaire made up of aluminium
material. The luminaire shall be of Matte Gold color and
dimesions (mm) shall follow as 300x300x1450 with lamp Base
E27 able to accommodate 1 X 20W lamp Max. Lamp shall be
supplied . Similar to above specs in Signify (Philips)/
Wipro/Osram/Havells/Legero or equivalent, upto satisfaction
of engineer incharge.
34
-
-
NS Item -Supply Installation, testing and comissioning of
Integral LED 4ft luminaire with PIR Sensor. The batten shall
be made up of CRCA housing and PC diffuser (Diffuser-Non
yellowing type). The luminaire should have a LEDs with colour
consistency SDCM = 5, CRI = 80 and CCT of 6500K.
Luminaire shall be designed to emit at least 4000 nominal
lumens at a system efficacy of at-least 120 lumen/watt. Power
consumption should not be more than 34W (±5%). The Life of
fixture (Including Driver):50000 burning Hrs. @ L70B50
Lumen maintenance @ design ambient temp 45 deg C. The
electronic driver used shall have a power factor =0.95 and
THD =10%, suitable for an operating voltage range of 140-
270V AC, Current Ripple =5%, Internal surge protection
should be minimum 4KV, electrical insulation class should be
Class I and driver should be of Class B serviceability. The PIR
sensor should be able to dim the fixture to 50% in case of no
movement. Sensor should have a detection angle of 60degree
and luminaire should be at least IP20 and IK02 rated. The
minimum dimensions (±5mm) of the batten shall be 44mm
(±5mm) X 51mm (±5mm)X 1221mm(±5mm). The luminaire
driver shall be of the same make/manufacturer as that of LED
luminaires. Luminaire manufacturer must have In-house
NABL accredited lab to conduct LM79, Type test as per
IS10322, `FAT` before dispatch as per IS 10322 and IK Test.
The successful bidder must submit the NABL accreditation
certificate for Luminaire manufacturer before supply of LED
luminaires for approval. The LED Luminaire and it`s driver
both should be BIS registered. Successful bidder shall submit
the following reports before supply of material for approvals
LM79 issued by NABL accredited lab, LM80 issued by LED
manufacturer, Type Test Certificate for luminaire as issued by
NABL accredited lab, BIS certificate for LED Luminaire and
Driver. Similar to above specs in Signify (Philips)/
Wipro//Havells or equivalent, upto satisfaction of engineer
incharge.
8
-
-
NS Item -Supply, Installation, Testing and Commissioning of
integral driver LED Steplight with a system lumen output of 40
lumens. The luminaire shall have a rated system lifetime of
25,000 burning hours at L70% lumen maintenance @ Ta plus
25deg C. The luminaire should have a color temperature of
Warm white 3000K and CRI = 80. The luminaire shall meet
IP67 rating with THD = 20% and PF = 0.9. The luminaire shall
have polycarbonate diffuser. The total power consumption
should not exceed 4W (including driver). Luminaire
manufacturer must have In-house NABL accredited lab to
conduct LM79, Type test as per IS10322, `FAT` before
dispatch as per IS 10322 and IK Test. The successful bidder
must submit the NABL accreditation certificate for Luminaire
manufacturer before supply of LED luminaires for approval.
The LED Luminaire and it`s driver both should be BIS
registered. Successful bidder shall submit the following
reports before supply of material for approvals LM79 issued by
NABL accredited lab, LM80 issued by LED manufacturer,
Type Test Certificate for luminaire as issued by NABL
accredited lab, BIS certificate for LED Luminaire. Similar to
above specs in Signify (Philips)/ Wipro/Osram/Havells/Legero
or equivalent, upto satisfaction of engineer incharge.
64
-
-
NS Item -Supply of single phase track for mounting mentioned
track light in Boq.Similar to above specs in Signify (Philips)/
Wipro/Osram/Havells/Legero or equivalent, upto satisfaction
of engineer incharge.
50
-
-
NS Item -Supply of track mounted cylinderical spot light True
Fashion, head dimensions: dia 80mm x H 135mm , driver
dimensions L171mm x W80mm x H40mm, 35w, 3000 lm
(@3000K), beam angle 34 deg°, pane angle 0°-320° and tilt
angle 0°-90°, CCT 4000K, CRI)90, SDCM(3 Efficacy 85lm/W,
Operating working temp range - 15°C ( Ta ( 35°C and
operating Voltage Range of 220-240 V AC,,Die -cast
aluminum housing, White/Black finish, Life L70B50 @ 50K
Hrs.@ 25 Degree Ambient temp. Luminaire manufacturer
must have In-house NABL accredited lab to conduct LM79,
Type test as per IS10322, `FAT` before dispatch as per IS
10322 and IK Test. The successful bidder must submit the
NABL accreditation certificate for Luminaire manufacturer
before supply of LED luminaires for approval. The LED
Luminaire should be BIS registered. Successful bidder shall
submit the following reports before supply of material for
approvals LM79 issued by NABL accredited lab, LM80 issued
by LED manufacturer, Type Test Certificate for luminaire as
issued by NABL accredited lab, BIS certificate for LED
Luminaire. Similar to above specs in Signify (Philips)/
Wipro//Havells or equivalent, upto satisfaction of engineer
incharge.
42
-
-
NS Item -Supply of LED surface mounted downlighter with
system lumen output of 6600 (±10%) lumens and maximum
system wattage of 66 Watts with a minimum system efficacy
of 100 lm/W. The luminaire should have a color temperature
of 6500K, CRI=80 and SDCM=5. The luminaire shall have
beam option of 60 Deg. The luminaire shall meet IP65 rating
with THD=20% and PF= 0.9. The luminaire housing shall be
of made up of die-cast aluminum with high glossy aluminium
mirror finish reflector. The fixture dimensions shall be 200mm
dia x 239mm height. Luminaire manufacturer must have Inhouse
NABL accredited lab to conduct LM79, Type test as per
IS10322, `FAT` before dispatch as per IS 10322 and IK Test.
The successful bidder must submit the NABL accreditation
certificate for Luminaire manufacturer before supply of LED
luminaires for approval. The LED Luminaire should be BIS
registered. Successful bidder shall submit the following
reports before supply of material for approvals LM79 issued by
NABL accredited lab, LM80 issued by LED manufacturer,
Type Test Certificate for luminaire as issued by NABL
accredited lab, BIS certificate for LED Luminaire. Similar to
above specs in Signify (Philips)/ Wipro//Havells or equivalent,
upto satisfaction of engineer incharge.
20
-
-
NS Item -Supply of LED Bulkhead Luminaries, made of high
pressure die-cast Aluminium body with polycarbonate
diffuser. Luminaries should be with minimum system efficacy
of 110Lumen/Watt and minimum system lumen output of 1100
(±5%) maintained at 70% at the end of 50,000 burning hours.
The luminaries should have CRI=80 and CCT of 6500K.
Luminaries shall meet IP66 and IK09 protection with THD less
than 10% and power factor = 0.90 . Luminaire should operate
in a voltage range of 140 to 270 volts AC. Luminaire
manufacturer must have In-house NABL accredited lab to
conduct LM79, Type test as per IS10322, `FAT` before
dispatch as per IS 10322 and IK Test. The successful bidder
must submit the NABL accreditation certificate for Luminaire
manufacturer before supply of LED luminaires for approval.
The LED Luminaire should be BIS registered. Successful
bidder shall submit the following reports before supply of
material for approvals LM79 issued by NABL accredited lab,
LM80 issued by LED manufacturer, Type Test Certificate for
luminaire as issued by NABL accredited lab, BIS certificate for
LED Luminaire . Similar to above specs in Signify (Philips)/
Wipro//Havells or equivalent, upto satisfaction of engineer
incharge.
20
-
-
NS Item -`Supply of IP66, sealed with anti-UV polyurethane
having lumen output from 1150lm per meter and CCT 3000K
SDCM= 4, better color consistency for visual comfort. The led
strip shall operate on voltage 24VDC. It shall have long
lifespan of 30K hrs. L70B50@35?. Led strip silicon material
seals without color shifting and anti-UV aging. It shall have
CRI90 for better vivid color rendering and shall operate on DC
low voltage driven for safetyshall be suitable for side view and
top view for bend option to fit for installation, similar to
Unilinear Flex Neon Strips. FLEXIBLE CHANNEL for
installation of product to also be included.Similar to above
specs in Signify (Philips)/ Wipro/Havells/ Legero or equivalent,
upto satisfaction of engineer incharge.
SIZE : 50 X 20( MM )
STANDARD LENGTH : 5 MTR WITH SINGLE CONNECTOR
COMPLETE WITH 12V - 2835 ( 120 LED ) - 8 MM
IP65 | 12 WATT / MTR | DOUBLE LINE | CUSTOMIZABLE
LENGTH
COLOR : WH-6K / NW-4K / WW-3K /RED / GREEN /BLUE`
220
-
-
NS Item -Transplanting of any large plants and trees on site in
building foot-print. Proper transplantation process to be
followed where root ball will be separated and bound in a
plastic bag for a month, after a month it will be transplanted to
the site, upto satisfaction of engineer in-charge.
14
-
-
NS Item -Credit of MS steel built up sections (both horizontal and vertical), brickwork, welded steel fabric mesh, etc.,recovered from demolition of existing building on site. The cost of the existing building materials of the above building have been worked out on the basis of theoritical quantities laid
on existing site. There shall be no measurement after actual scarifying/ dismantling and no claim of agency on this score will be entertained and full recovery on the basis of quoted rate exhibited in the BOQ shall be made. No rates below reserve price will be considered for all purpose in case the agency quotes lesser than reserve price. The rate shall also include the disposal of waste material. All works upto satisfaction of engineer incharge.The price qouted against the recovery material shall have minimum reserve price of 10,00,000/- per job).
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements