Government Of Haryana Tender

10.41 Cement concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth

11.2 First Class brick work laid in cement sand motor 1:6 in foundation and plinth

15.6 12mm thick cement plaster 1:5

31.12 ( a ) Main Switches Supply and erection of metal clad switches / B.D.Bs with rag bolts on wall or on existing angle iron board / pedestal including bonding to earth and necessary connections . 31.12(a)(xxvii) Cat-B Four pole change over switch 300/320 amp. 415 Volts.

31.12 (c) Moulded case Circuit breakers. Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. 31.12 c (i) 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

31.12 c (ii) 100 amp.to 220 amp.415 V,10 KA 3-phase.

31.12 c (iii) 250 amp. 415 V , 35 KA 3-phase.

31.12 c (iv) 300 amp. to 400 amp. 415 V , 35 KA 3-phase.

(P) Pipe Laying. 31.21 Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. 31.21 (vii) Galvanised iron pipe 65 mm dia on surface.

31.22 Earthing

31.22(iii) Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as equired.

31.22(iv) Earthing with tinned copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) comlete as equired.

31.22(v) Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode.

31.22(x) Pdg. and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required .

31.22(xi) Pdg. and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required .

31.22(xiv) Pdg. and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required with all labour and material.

31.22(xv) Pdg. and fixing 25 mm x 5 mm G.I. Strip on surface or in recess for connections etc. as required with all labour and material.

31.26 Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections . 31.26 (xxix) Ard. 95 Sq. mm 3.5 Core Cable .

31.26 (xxx) Ard. 120 Sq. mm 3.5 Core Cable .

31.26 (xxxii) Ard. 185 Sq. mm 3.5 Core Cable .

31.26 (xxxiii) Ard. 240 Sq. mm 3.5 Core Cable .

31.28 Supply and erection of suitable compression type brass cable glands for underground Cable. 31.28 (v) 120 Sqmm to 185 Sqmm Cable 3 to 3.5 Core

(T) Street Light 31.30 (VI) Supply and erection of prestressed cement concrete pole as per IS : 1678-1960. 31.30 (VI) (ii) 9 metres long 105 mm x 115 mm at top and 105 mm x 315 mm at bottom with working load of 200 Kg. burried 1.80 m in ground.

31.63 Supply installation testing and commissioning of wall/ free standing floor mounting dust and vermin proof compartmentalized cubical panel made out of 2mm thick CRCA street, required hardware 3 mm thick bakelite sheet provided all along with bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 coat of zinc/ Red oxide primer followed by 2 coat of powder coating in gray or required shade after rising. The panel having PU/Neoprene rubber gasket of not less than 3 mm thickness separate detachable gland plate MS base channel hinged door with inter locking agreement for equipment / switch wear. Transparent acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3 mm thick for separately cable alley to BBC from switch chamber Extended solid copper bars upto cable alleys shall be provided for outgoing connection which shall be paid as extra items. Side walls and cable alley compartments shall be having bolted type doors with detachable extension type structure. the panel will be complete with control wiring (copper) and fuse protection ( only outer area on all sides shall be measured)

31.64 Supplying and fixing of copper bus bar duly tinned by means of SMC / BMC type insulatter high tensile nuts and bolts spring washer fixing to same in existing pannel including bending, cutting in required shape and size and insulation with colour coding heat shrinkable PVC insulation complete in all respect.

31.65 Pdg. and fixing digital metering equipment for LT cubical panel consisting of 96 mm x 96mm 0-500V, Volt meter with selector switch amp meter (Of required ratio upto 600/5 amp) with selector switch and required C.Ts 3 Nos. a set of 3 Nos. phase indication lamp RYB LED.

31.66 Supply and fixing of rotary handle for on/off operation of existing MCCBs in the L.T panel including fixing the same in position with all labour and material required to complete the job in all respect. (i) Rotary handle upto 125 A MCCB

(ii) Rotary handle above 125 A MCCB

31.67 Supply and errection of double walled corrugated (DWC) HDPE pipe laid 1 meter below ground level including diging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including the cost of the labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

(ii) HDPE pipe 145/123 mm outer dia / inner dia

31.71 Supply and erection of XLPE (E) 11 KV HT aluminum conductor armoured cable ISI mark laid in existing pipe / trenches / surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work. (ii) 50 sqmm 3 core XLPE Cable

31.72 Supply and erection of heat shrinkage type end termination jointing kit indoor type of suitable to accommodate 3 core 11 KV XLPE aluminum cable/ ABC cable complete with all the kit contents including earth continuing connection along with 3 nos. crimpling type aluminum lugs of suitable capacity including making joining etc complete in all respect. (i) Suitable for 16 to 50 sqmm 3 core XLPE Cable

31.73 Supply and erection of heat shrinkage type end termination jointing kit outdoor type of suitable to accommodate 3 core 11 KV XLPE aluminum cable/ ABC cable complete with all the kit contents including earth continuing connection along with 3 nos. crimpling type aluminum lugs of suitable capacity including making joining etc complete in all respect. (i) Suitable for 16 to 50 sqmm 3 core XLPE Cable

M.R. items NS-1 Supply, erection, testing and commissioning of outdoor type copper wound, transformer of 250 KVA 11 / 433 KV, 3 Phase, 50 Hz complete in all respect upto the entire satisfaction of Engineer-in-charge of work ( on existing pole / plateform including first filling of oil conforming to IS 335 of 1972 ) KVA 250 No. load voltage ratio 11/ 0.433 KV No. of Phase 3 Frequency cycles 50 Hz Types Double wound core type Copper wound. Cooling ONAN Duty Outdoor Vector Group ISS-DYN 11 / IS 2026 /77 Tapping on HV compensation +5% to - 5% Insteps of 2.5% Temperature rise (Oil / res.00) 500 / 550 C Attitude upto 1000 m above MSL Off circuit tape changer Externally hand operated Oil conservator with filling hole & cap Plain oil level gauge with minimum level marking Thermometer pocket 4 Nos. Plain roller undirectional. 1 No. 4" dial type thermometer Silica Gel breather Ist filling of oil. Drain cum filter valve with plug. Rating & diagram plate. Two earthing terminals

Lifting arrangement Explosion vent Air release plug. Oil conservator tank Shunt off valve between buchloz & conservator TERMINATION HV-3 Pole single glands cable box suitable for reception of one No. 3 core upto 120 sqmm HT XLPE cable including compound for filling the cable end box with Al. lugs / thimble. LV- 4 Pole 3 glands cable boxes suitable for 3 Nos. 240 sqmm 3.5 core Polyvinyl chloride cable having extended copper bars of requisite Capacity from LT bushing for making connections with cable including cost of Al. lugs, thimbles LV : Neutral suitable cable Box for earthing provided.

NS-2 Supply, erection, testing & commissioning of 11 KV indoor H.T. Metering panel complete with CTs, PTs cubical and electronics meter with accuracy class 0.5 as per requirement / approved by HVPN Consisting of the following : (i) Cubical panel free standing floor mounting type made of sheet steel 14-G SWG CRCA sheet with channel iron / angle base frame spray paintd with strong Synthetic grey channel paint as per size & design approved by HVPN . (ii) 3 Nos. 11 KV CTs of rating as approved by HVPN for indoor installation of approved make of HVPN. (iii) One No. 11 KV PT 11000/110 Volts 10 KA burden 0.5 accuracy oil filled suitable for indoor installation of approved make of HVPN. (iv) Digital electronic meter 3 Phase 4 wires 0.5 accuracy for recording reading operating system for difference kind of readings. The cubical panel will be complete in all respect including interconnection, internal wiring with PVC copper cable its testing / approval of all times by HVPN including cost of all testing / approval charges of all items by HVPN with a guarantee of one year from the date of commissioning including cost of all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work.

NS-3 Supply, erection, testing & commissioning of cubical type dust & vermin proof LT automatic power factor control panel 80 KVAR capacity suitable for automatic operation and control power factor within the set limit free standing floor mounting made out of 14 G mild steel sheet with channel iron base frame painted with stoving synthetic light grey enameled paint suitable for operation on 3 phae 4 wire 50 cycles, per second 400 / 440 volts AC supply equipped with the following ( as per diagram attached ) 1 No. automatic power factor control relay of GE / L&T make space for incomer 200 amp tripple pole MCCB. A set of pilot lamp ( 3 Nos. ) phase indicating lamp of L&T make iron clad bus bar chamber suitable for 200 Amp. 440 V having 3 Nos. phase copper bars of cross-section 25 mm x 05 mm and 1 No. neutral copper bars of cross-section 20 mm x 5 mm duly tinned and insulated with polyvinyl chloride sleeving with requisite clearance as per ISS connection from incomer 200 amp. 4 pole MCCB to bus bar by means of solid copper strips of requisite capacity duly tinned & insulated with PVC sleeving. 3 Nos. 3 Phase 15 KVAR capacitor of Havells / Epcos / Noptune / L&T / Siemens make ( Total 45 KVAR ). 4 Nos. 3 Phase 10 KVAR capacitor of of Havells / Epcos / Noptune / L&T / Siemens make make ( Total 35 KVAR ). ( 1+3) 3 Nos. 3 Phase 63 Amp. Contactors for 15 KVAR capacitor of L.T. make. 4 Nos. 3 Phase 32 Amp. Contactors for 10 KVAR capacitor of L.T. make. 9 Nos. 63 Amp. HRC fuse for 15 KVAR capacitor of L.&T / GE make. 12 Nos. 32 Amp. HRC fuse for 10 KVAR capacitor of L.&T / GE make. 7 Nos. indicator lamp 220 volts for an indicator of respective capacitor bank of L&T / Siemens make. 7 Nos. control fuses for each capacitor of L&T / GE make. 7 Nos. auto manual selector switch of L&T / GE make. CTs of ratio 200 / 5 amp of AE make as per required load of building.

16 Nos. push button on / off for manual operating of required of L&T make connection from bus bar to capacitor by means of 16 sqmm PVC copper cable, earthing copper bus bar of cross-section 20 mm x 5 mm duly tinned throughout the length of panel.

NS-4 Supply and erection of Fire extinguisher ISI mark ( Ajay make ) Co2 type of 4.5 Kg. capacity as per IS 7285 duly erected / hung on wall with hooks with all labour & petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work make and model approved by Cheif Electrical Inspector.

NS-5 Supply & erection of MS bucket stand which include cost of 6 Nos. fire bucket with 9 liter capacity with stand filling including cost of welding & painting of complete stand & buckets with one coat of red oxide and two coats of approved paint of red colour written with fire on the buckets as per fire protection with all labour and material required to compelte the job in all respect upto the entire satisfaction of Engineer-in-charge of work.

NS-6 S/E of 11 KV gang operated switch 'Jayshree make' conforming to IS with latest amendment including suitable size of copper blade erection of same on the existing 'H' pole with the help of 3 Nos. channels of size 75 mm x 40 mm x 6 mm, 1.8 M. long fixed with suitable size of MS clamp, nuts & bolts including cost of 6 Nos. 11 KV insulator with GI Pin, RD fuses and painting with 2 coats of approved paint and one coat of red oxide material required to complete the job in all respect utpo the entire satisfaction of Engineer-in-charge of work.

NS-7 Supply & erection of lightening Arrestor Model SDU ALPRO make suitable for 11 KV 3 Phase 50 Hz grounded neutral system comprising of Speek gap type ( Quench gap type ) in series with non liner resister element housesed in horizontally Scale porcelain bushing with line and ground terminal along with mounting clamps Conforming to ISS 3070 (Part-1) of 1985 with latest amendment with all labour and material required to complete the job in all respect utpo the entire satisfaction of Engineer-in-charge of work.

NS-8 Providing and fixing of stay set complete with stay wire with dis insulator as per specification upto the entire satisfaction of Engineer-in-charge of work.

NS-9 Providing and fixing of wire mesh jali around the transformer of size 4'x 8' made out of 75 x 25 x 3.25 mm jali fixed with angle iron frame made out of M.S. angle 50 x 50 x 6 mm support of M.S. flat 50 x 6 mm and fixed in C.C. Block 1:2:4 including cutting, welding etc. as per drawing complete in all respect upto the entire satisfaction of the Engineer-in-Charge.

NS-10 Erection of MS Angle 50 x 50 x 6 mm, M.S. flat & nuts & bolts including cutting, bending to the required shape drilling holding carriage, painting loading & unloading complete in all respect.