Public Works Department Tender

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79) (b) Ist Quality

Removing doors and windows (wooden and steel) together with the dismantling of walls (a) Doors [HSR 8.17 (a)]

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete [HSR18.34 (a)] (a) Door and window frame of size 89 mm X 50 mm with 40 mm wide single rebate

(d) Door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (b) in cement (HSR 8.5 (b))

Dismatnling Roofing (g) demolishing mud phaska in tile terracing (HSR 8.8 (g))

Stripping and stacking slates or tiles of a roof (HSR 8.10)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50)

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

10 mm thick cement plaster 1:3 (HSR 15.2)

12 mm thick cement plaster 1:6 (HSR 15.7)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.16591969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd,conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (HSR 17.93 (a) (i)) - Note HSR 17.18

Cupboard shutters of commercial hard wood such as hollock, champ, chikrasy and chaplash etc., (non-coniferous timber other than teak conforming to I.S. specification no.1003, kiln seasoned) excluding chowkat but with commercial plywood panels or faced on one side including iron hinges and screws fixed in position ( excluding the cost of handles, tower bolts, hasp with stample, but including the labour for fixing the same. (HSR 17.32 (b))

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1)

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No.1003, kiln-seasoned), with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks /cleats, stops, nails etc., complete, fixed in position (excluding the cost of any fittings,other than specified above, but including labour for fixing the same in position). (HSR 17.90) - Note HSR 17.18.

Applying pink primer or aluminium priming ocat on wood work including preparation of surface, Knotting and stopping etc. (HSR 16.2)

Cost of aluminium fittings complete for doors and windows, such as tower bolts,handles,etc., and screws for these fittings (excluding sliding bolt) (HSR 17.72)

Supplying and fixing glass panes including special metal sash putty of approved make (HSR 18.30) (b) glass panes 4 mm thick, exceeding 40 sq dm areas

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Providing and fixing 1st quality ceramic-glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer -In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. [HSR 14.92] (b)

Providing and fixing sliding bolt with nuts and screws,etc.,complete (HSR 17.83 (b)) Size 300 mm X 16 mm

Size 250 mm X 16 mm

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge [HSR 13.89]. Note:- The agency to whom the work is alloted will have to produce original bill / voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC pipe 6 kg. pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge [HSR 13.90]. Note:- The agency to whom the work is alloted will have to produce original bill / voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC Bend.

First class brickwork laid in cement sand mortar 1:4 in first storey upto 4 meters above plinth level. (HSR 11.9)

Providing and laying GRANULAR SUB BASE consisting of filter / Drainage layer conforming to Table 400.1 Grading – III / VI of MoRT&H 5th Edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No: 401 of MoRT&H specifications.

Providing and laying 60mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 25mm thick fine sand complete in all respect (HSR 10.158)

Precast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including from work, placing and fixing in position, complete at the ground level or in first storey. (HSR 10.77)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces.. (HSR 16.25+16.3)

Public Health:- Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (a) Single trap syphonic W.C. Suite (ii) Single colour [HSR 30.5 (a) (ii)].

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing over flow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks completein all respects to the satisfaction of Engineer-In-Charge. (Except civil work).(HSR 30.119) 1000 Ltr. Capacity

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with raw slugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) 25 MM DIA C.P.BRASS ADJUSTABLE 750 mm long [HSR 30.68 a(i) ]

(b) 20 MM DIA C.P.BRASS ADJUSTABLE (ii) 600 mm long

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc. (a) C.P.BRASS (i) Soap dish large [HSR 30.70 a(i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) INDIAN MAKE (i) 600mm X 450mm [HSR 30.71 a(i)]

PROVIDING AND FIXING POSITION BEST INDIAN MAKE FLAT BACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH CONSISTING OF : - (i) Flat back lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval of the Engineer-in-charge). (ii) 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I.AUTOMATIC FLUSHING CISTERN, PAINTED WITH non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15 mm pipe; (iii) PAIR OF R.S.PR C,I. PAINTED BRACKETS AND BRASS COUPLINGS; (iv) Standard size G.I.FLUSH PIPE WITH C.P.BRASS WALL CLIPS AND UNIONS COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in charge). [HSR 30.19 (iv)](i) White

Providing and fixing 25mm thick marble partition for different type of urinals (b) VITREOUS CHINAWARE PARTITION PLATE (II) LARGE SIZE 835mm X 355mm (HSR 30.40 (b) (ii) (i)) (i) White

Providing and fixing in position best Indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully described in item No. 30.41 above) [HSR 30.42 (iii)] White Size 610mm x 510 mm with one no. tap

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF TWO URINALS LARGE FLAT BACK OR ANGULAR LIPPED FRONT 610MM HIGH IN VITREOUS CHINAWARE WITH 5 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC.COMPLETE as fully described in item no.30.25 above. Range of two urinals (ii) Single colour [HSR 30.26 (ii)]

PROVIDING AND FIXING IN POSITION BEST QUALITY STAINLESS STELL SINKS . a) 600mm X 450mm X 200mm [HSR 30.53)(a)]

PROVIDING AND FIXING IN POSITION AUTOMATIC BRASS BALL VALVES IN TANKS (a) WITH COPPER BALL (i) 15 mm internal diameter [HSR 30.110 a (i)]

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (ii)].

Providing and fixing C.P. brass liquid soap container of best quality (as required by the Engineer-in-charge). (HSR 30.77).

Providing and fixing in position best Indian make flexible tube connection. (b) C.P. Brass (iii) 15mm x 450 mm. [HSR 30.82 (b) (iii)].

Recovery items: The rates quoted against recovery items will not be included in the total amount rather is will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specification) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under:- Doors and windows @ 200 Each Note: - All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.