Directorate Of Urban Local Bodies Tender

Repairing of old play equipment : Chain Swing , Bridge Ladder , Slide Ladder and Sea Saw including rubbing , painting and spraying with good finish by painting machine at site complete in all respect to full satisfaction of Engineer-in-chief.

Supply of Rectangular Bench Overall Dimensions: Platform size - 1500mm length , 450 mm width, 100mm thickness and 450 mm height with two legs of 150 mm thickness. • Sitting Platform is in any bright color while the legs are in contrasting color as directed by Engineer In-charge. • Manufactured by using M-30 grade of Concrete. • Suitably reinforced to promote long use and to prevent damage during handling, transportation and erection. • Treated with special anti -corrosive, water proof coating so as to make the surface glossy and water proof. Complete in all respect to full satisfaction of Engineer-in-chief.

Supply of Curved Bench • Overall Dimensions : Platform size - 1200mm length 350 mm width, 450mm height • Sitting Platform is in any bright color while the legs are in contrasting color as directed by Engineer In-charge. • Manufactured by using M-30 grade of Concrete. • Suitably reinforced to promote long use and to prevent damage during handling, transportation and erection. • Treated with special anti -corrosive, water proof coating so as to make the surface glossy and water proof. Complete in all respect to full satisfaction of Engineer-in-chief.

Supply of Stool having Overall Dimension: 400 mm Dia x 400 mm Height x 100 mm Seat Thickness x 300 mm Stem Length. Platform 600 mm x 600 mm x 50mm Thickness. • Sitting Platform is in any bright colour while the legs are in contrasting colour as directed by Engineer In-charge. • Manufactured by using M-30 grade of Concrete. • Suitably reinforced to promote long use and to prevent damage during handling, transportation and erection. • Treated with special anti -corrosive, water proof coating so as to make the surface glossy and water proof. Complete in all respect to full satisfaction of Engineer-in-chief.

Supply of an Eye Pleasing Polymer Concrete Dustbin Total Height- 1200mm, Top Cover Size 450mm x 435mm with clear opening of 330mm x 170mm, base size- 390mmx390mm. WHICH CONTAINS • Polymer concrete container • Polymer concrete top container cover • Polymer concrete waste access cover • Polymer concrete base Dustbin are manufactured with full MS Bar caging for added strength and durability Complete in all respect to full satisfaction of Engineer-in-chief.

Air Walker: Providing, designing and fixing of Air-Walker of size 100 x 550 x 1480mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick made up of hot rolled tubular steel and hot dipped galvanized, and powder coated 80-120 micron thick using Akzo Nobel or equivalent in desired shade and colour. All welding joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Base plate cover shall be made up of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness U V resistant and colour as approved by Engineer-in Charge. High quality grip rubber should be used on handles. Foothold shall be made of Nylon alloy with rounded edge to prevent impact and injury. Maintenance free bearing should be used in equipment manufactured by reputed company duly sealed and self lubricated to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters . The equipment should be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

Sit Up Station: Providing, designing and fixing of double sit-up station of size 1500 x 1150 x 650 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and Base plate cover shall be made up of virgin LLDPE plastic by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. The equipment should be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and when concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

Air Swing: Providing, designing and fixing of airs winging pair of size 1150 x900 x1250 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and Base plate cover shall be made up of virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintained free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Leg Press: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 2000 X 550 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

Pull Chair: Providing, designing and fixing of Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Arm Wheel :- Providing, designing and fixing Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Providing and fixing of slide ladder childern play equipment12’ long x 16’ wide x 5’ high (above ground) slide is Made of S.S Sheet 18 SWG mounted on M.S Angle 40x400x4 mm Slide 2 no. vertical support of M.S Pipe 1” B class Ladder having climbing Steps of pipe ½” B Class complete with Painting and to be fixed in CC Blocks 12” x 12” x 15” in to 4 legs of mix in ratio1:2:4 including carriage charges.

Providing and fixing of bridge ladder 16’ long x 2’ wide x 6’ high (above ground) slide is Made of M.S pipe 2” B class and Climbing Steps of pipe ¾” B Class complete With Painting and to be fixed in CC Blocks 12” x 12” x 15” in to 4 legs of mix in ratio 1:2:4 including carriage charges.

Providing and fixing of Chain swing 10’ long x 9’ high (above ground) frame is Made of M.S pipe 2” B class which stay with M.S Pipe 1” B class frame is connected with M.S rod 25 mm dia shafts having fabricated ball Bearing no. 3204 shaft, further having 2 no. Seating belt type seat welded with 8mm Thick M.S Complete with painting and fixed in CC Blocks 12” x 12” x 15” in to 4 legs Of mix in ratio 1:2:4 including Carriage charges.

Double Cross Walker :- Providing, designing and fixing Double Cross Walker of size 1600 X 600 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Seated Chest Press :- Providing, designing and fixing Seated Chest Press of Pull pair of size 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Providing and fixing of MS Sheet of 16 Gauge Complete in all respect to full satisfaction of Engineer-in-chief.

Providing and Fixing Multi Play Activity equipment Covering Area: 27’L x 13’W FRP Wave Slide 6mm thick at 5’H – 2set. FRP Square Canopy 2mm thick -2set FRP Fancy Railing Monkey and Frog shape-4set. FRP Platform 3’.5 x 3’.5 x 5mm thick-2set. M.S Walking Bridge 6’Long -1set. M.S Safety railing – 2set. M.S Climbing Ladder-2set. M.S Wave Climbing Ladder 8’Long-1set. M.S Sea-Saw (Double) 7’long having 4no FRP Sitting seat of 3mm thick With jerk proof system using 4no semi tyres- 1set. M.S vertical station of m.s pipe 2”.5 x 12Gauge ISI Mark-2set. Complete item priming and Painting in P.U Paints and fitting at site complete in all respect engineer in the charge.