Directorate Of Urban Local Bodies Tender

Wave Slide: 9’.5 L x 5’H. Wave slide is of molded Fiberglass Reinforced Plastic (FRP) of 6mm thick and climbing ladder is of m.s pipe 1” x 12 gauge and m.s rectangular pipe

NS Item= Ornamental Canopy with base complete in all respect – with 6 No. Ornamental Design FRP Molded Pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 20mm drilled in the base with hold fasts and having B class pipe of size 88 mm and height 2890mm, the central m.s pipe holds FRP Molded taj 6no of size 260 x 260 x 210mm high suitably mounted at appropriate height complete as per design. Complete pillar suitably grinded and subsequently spray painted with two coats of P.U Paints in required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design. The spandrel (L-Bracket) having length 420mm and height 400mm the frieze (Top Panel) height 250mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 50mm x 25mm, frieze properly welded to the column pillars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with P.U Paints. (iii ) 3 No. cast iron/frp base panel railing with frame Floral and Ornate decorative design cast iron/frp side railing panel as per design having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 50 x 25 mm. The bottom mild steel pipe having 2 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 250mm welded at the base to hold the panel in the ground. Every panel length is as per the gap between the two pillars. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with P.U Paint in required shade. (iv) One set of top frame with Double Finishing FRP Molded Plastic Sheet roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 4 mm thick with top and bottom good finishing (Double finishing sheet) to make it rust proof bent to profile of size 245mm width in -Z- section on either ends fixed horizontally along the length between column pillars. Also it contain FRP Moulded Ball of 14”Dia x 2mm thick at the central top for its beautification. Each sheet enamel painted in red color. Each such sheet properly riveted to horizontal sheets. The complete item is fitting at site with installation and construction of canopy base should be made of earth work .15 m deep, Brick ballast .15 m depth,two steps of first class brick work 1:5 of 3.00 mX.30 mX.45 m and 3.00 m X.30 m X.60m, cement concerete on .10 height and finishing with checqurred tiles on the base and steps. (Including fixing at site and supervision and transportation and all type taxes)

Providing And Installation Of Kids Play Equipment -Jungle Gym AREA : 25 X 18 X 12 FEET AGE GROUP : 3-12 YRS CAPACITY : 3-10 “A” Class ISI marked MS Pipe of Reputed Brand (Jindal, Apollo, Bharat Etc). Frp items – 2 wave slide , 2 frp roof , 1 frp tunnel , and all base with frp chequered (non-slippery ), 1 fish attached to climber. SWING SEAT : RUBBER TYPE MAKE IN INDIA FRP Thickness between 3 To 8 mm. PU Coated Paint finish on the MS Structure. As Per Approved Design, including fixing In Ground With cement concrete at specified location till the satisfaction Of Engineer Incharge. As per reference image attached in annexure. Including GST and other Charges.

Pull Chair:- Providing, and fixing of Pull pair of size 2500 X 800 X 2000 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 3.0 mm thick all pipes made up of hot roiled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc .primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be` made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GULLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix theequipment on to it and cover nuts and bolts with the baseplate cover, all complete as per directions of Engineer in Charge.

Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x 600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge.Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and a. .royal of arge regari ing materia , s ape of equipment,colour on metal, seat and base cover plate and fixing of equipment etc.

Leg Press: Providing designing and fixing of leg press of size 2000x550x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micror thick

Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc.`` `

Rowing machine: Providing designing and fixing rowing machine of size 1280x800x1150 mm fabricated with main past of 114 mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 3mm colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipments to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate A.I complete as per direction and approval of engineer in charge regarding material shape of equipment colour on metal seat and base pedal and fixing of equipments etc (the cement concrete and excavation work shall be paid for separately).