Command Area Development Authority Tender

Providing, laying, aligning, and jointing with uPVC heavy body solvent at all level/ depths ISI marked PVC pipe of pressure as per design for raw water supply as per IS 4985 (amended up to date) in trenches in complete, including cost of all Specials, labour, and commissioning as per Technical Specifications and approved make as per direction of Engineer. (Make Duraline,Reliance, jain Irrigation, Nimbus, Finolex, Hasti, or equivalent) (Rate analysed with rate approved by worthy Administrator) a) PVC 4 Kg/Cm2, 110mm dia Pipe

Providing fixing of Header Assembly/Manifold 3` to connenct the filtration unit (loose) (Rate app. By worthy Administrator)

Complete operation and Maintenance and watch and ward of the project for one year including operation of pump, pipe line, accessories, electromechanical, solar plants complet in all respect of pump house, pipe line and accessories, electromechanical, solar plant etc complete in all respect for one year

Providing, fixing, testing and commissioning of pressure gauge 2” dial with Glycerin filled (NS Item)

Providing and fixing of three phase 50Hz ±3% rated motor, frequency 415V ± 3% rated motor voltage, with constant motor flux control, (Submersible motors shall conform to all the requirements of IS 9283) Solar A.C. Agricultural Pumps alongwith Universal Solar Pump Controller (USPC) all external part of motor used in open well submersible pump having casing of Alloy steel confirming to IS 3444 including all PVC insulated polymer sheathed 3 core flat type cabling in conduit, required from solar plant to solar pump through control room required to connect, including cost of and as per IS code 14220-2018 including third party inspection.Average discharge 13 LPS / Head 52 meter / minimum / minimum outpurating of 15 KW. Dualy installed on the suitable foundation. Actual pump set`s parameters will be finalized after approval of design and drawing. Solar Pumping Sets should be of the make: KSB / Shakti/ Kirloskar /CRI/Lubi/ Crompton/ WPIL, (NS Item) @ Rs 11002.53/- per HP Quantities are total sum of varrious pumps capacity in HP may varry as per design requirement for site.

Providing, laying, aligning, and jointing with uPVC heavy body solvent at all level/ depths ISI marked PVC pipe of pressure as per design for raw water supply as per IS 4985 (amended up to date) in trenches in complete, including cost of all Specials, labour, and commissioning as per Technical Specifications and approved make as per direction of Engineer. (Make Duraline,Reliance, jain Irrigation, Nimbus, Finolex, Hasti, or equivalent) (Rate analysed with rate approved by worthy Administrator) a) PVC 4 Kg/Cm2, 140mm dia Pipe

Providing and lowering of HDPE floater manufactured with 225 mm dia PE pipe having PE-80 and PN-10 to float the submersible open well pump/motor (NS item)

`Supply Installation testing commissioning of Solar Photovoltaic Stand alone Plant conforming to MNRE specifications as amended, consisting of Mono Crystalline silicon solar cells, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength. Including lightning and surge voltage protection, Fixing of Array junction box and Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required, built in metering system to moniter plant performence (Amp-meter, Volt-meter, Frequency meter, Energy meter, Watt-meter, and other instrument/equipment as required) Note:- PV modules used must qualify to the latest edition of IEC PV module qualification test or equivalent BIS standards Mono Crystalline Silicon Solar Cell Modules IEC 61215/IS14286. In addition, the modules must conform to IEC 61730 Part-1- requirements for construction and Part 2 – requirements for testing, for safety qualification or quivalent IS and be mounted on fixed Aluminium/GI structure of adequate strength and design as per IEC/IS specification. Including field-based electroluminescence (EL) study be performed after receiving the modules at site and after installation. Module mounting structure (MMS) design and drawing shall be duly vetted from government institute Including third party inspection Actual parameters/capacity will be finalized after approval of design and drawing. (N.S. Item)`non schedule

Construction of 6`x6` regulation hut constructed with 9` thick brick masonary inner side covered with 1.25 mm thick class-1 GI corrugated sheets (with 750 gm Zinc coating per sqm on its both sides) provided with proper door and windows as per approved design and drawing inner size 6`x6` Av. Height 8` covered with Precoated G.I. Corrugated sheet ( Non Scheduled item )

Hydrant assembly for Nakka in fields, Rates are including rates of Tee, riser pipe, butterfly valve, Flange and labour for fixing butter fly valve should be as per IS 13095-2020

Supply and jointing of 110 mm 6 Kg/cm2 HDPE pipe (for jointing floater, all filters, PRV etc)