Citizen Resources Information Department Tender

Brick work with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:6 (1 cement: 6 coarse sand) (Notes:‐ 9. The rates are exclusive of GST but inclusive of all other taxes, Labour Welfare Cess and contractor'sprofit.)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

Providing and laying Size of Tile 600x600 mm vitrified/retrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc..All work completed in all respect to the satisfaction of Driisya engineer incharge.

Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing All work completed in all respect to the satisfaction of Driisya engineer incharge.

Floor mounted white vitreous china double trap syphonic WC with 10 litre cistern and each 9500 all fittings & fixtures, seat cover etc (Notes:- 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

White Vetrious China Waterless Urinal of size 600x330x315 mm (Notes:- 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

Providing and fixing white vitreous chinaware laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Health Faucet (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

Angle valve (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

C.P. Brass long Nose bibcock 15 mm (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

Soap Dish (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

Towel Rod (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

Toilet paper holder (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

CP Nipple 12mm dia 50mm length (Notes:‐ 1. These rates are exclusive of GST, contractor's profit, over heads, labour cess and carriage etc.)

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing of fitting not mentioned in point no. 21 but required for completion of work and make funtional water supply and sewerage system of washroomcomplete in all respect.All work completed in all respect to the satisfaction of Driisya engineer incharge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :- Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Cold twisted bars

Painting the wooden and metal surface with deco paint of approved brand and manufacture to give an even shade. Two or more coats on old work All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of With toughened glass panes of 6 mm thickness (weight not less sqm than 15 kg/sqm)

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

Wall paintng with plastic emulsion paint of approved brand and manufacture to give an even shade (one or more coats on old work)

Finishing walls with textured exterior paint of required shade :

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required

Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe.

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required.

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required.

1 run of Size 1.50 Sqmm(1/1.40mm)

1 run of Size 2.50 Sqmm(1.1.80mm)

1 run of Size 4 Sqmm(1/2.24mm)

1 run of Size 10 Sqmm(1/3.50 mm)

Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. All work completed in all respect to the satisfaction of Driisya engineer incharge.

MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal /Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work.TRIPLE POLE MCCB 125 to 160 Amp, 25 KA All work completed in all respect to the satisfaction of Driisya engineer incharge.

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 16 way ( 2 incoming and 14 outgoing) All work completed in all respect to the satisfaction of Driisya engineer incharge.

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:-.

6 amp. to 32 amp Single Pole

40 amp to 63 amp. Double pole

40 amp to 63 amp. MCB's FOUR POLE

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. step type Fan Regulator 2 modules 300 watt. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate

Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer- in-charge : 48" (1200mm)

Supplying, errection, testing of Exhaust fan (as per IS code 374) having a each capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge.

Supplying and drawing of 1 no UTP 4 pair CAT Sa LAN Cable in the existing surface/recess MS/PVC conduit as required

Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. 2 pair telephone wire.

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 4 Modules.

RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type

Supply Of Telephone Hand sett approved make. (Supply as pre-approved design by Driisya Engineer Incharge)

SUPPLY ONLY 12 U RACK FOR COMPUTER NETWORKING OF COMARACK MAKE. (Supply as pre-approved design by Driisya Engineer Incharge)

Providing and fixing white marker board past on wooden paneling. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Taking out existing wooden door/window shutter, repair by cutting, painting etc. and refixing of repaired door/window shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing wooden paneling on door frame with a frame work not more 600mm gap between using 18mm thick waterproof ply or (18 mm thick HDHMR board of Action Tesa Company ) conforming IS standard 303 (i.e veneers treated with preservatives, glue line fortified with nonleachable organophosphorus compound and FTP technology) of commercial plywood, finished with 12mm commercial ply or (12 mm thick HDHMR board ) conforming IS standard 303 (i.e veneers treated with preservatives, glue line fortified with non leachable organophosphorus compound and FTP technology) of commercial plywood and with teak corner fixed to the edge, including all zinc plated joineries and fixtures i.e. nails etc.The Paneling finished with 1mm thick approved shade of laminate of Greenlam or Merino Company. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing partially glazed/ non glazed partition 75 mm thick of using kail/miranti wood frame work of size 50mmX38mm treated fire retardant & anti termite paint spacing not exceeding 600mm C/C horizontally as well as vertically (joint less vertical member) or( 50mm X 25mm aluminium tube ). Bottom of the frame work to seemed to the floor & slab with concealed hardware & screws & adhesive, wherever necessary, frame to be sandwiched in between 12mm thick commercial ply conforming IS standard 303 (i.e veneers treated with preservatives, glue line fortified with non leachable organophosphorus compound and FTP technology) of commercial plywood or ( 12mm thick HDHMR Board of Action Tesa Company ) & finished with 1.0 mm thick laminate on both sides of Merino or Greenlam, including all zinc plated joineries and fixtures i.e. nails etc.. All exposed faces to be finished with Steam beech wood beading & all wooden surfaces to be finished. with lacquer polish, of approved shade, float glass 6 mm thick not larger than 1.2m in width shall be fixed with Steam beech wood beading 12.5mmx12.5mm. Rate includes design & grooves in laminates, provision for extra frame work as & where necessary for skirting and making cutout for switch plate, switch boxes, light fittings etc. making provision for laying conduits. full height partition will be measured from finish Floor level to the bottom of false ceiling. [Note:- for UPS/ Battery room only, instead of 12mm ply, 12mm cement composite fiber board of bison make shall be used, and instead of laminate, shall be painted with rustic paint as discussed in paint column. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing 2210mm, 1200mm and 813mm various height modular file storage units with depth 380mm, width of the filing cabinet shall be of standard size of ranging between 380-450mm. Filing cabinet shall be provided with Single/ double leaved hinged shutter made of made of 18mm thick HDHMR/HDF/MDF board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only, heat processed using roller heat press machine to get better finish long sustenance with all edges having 0.8 mm thick edge banding of Rehau company to match the fascia and on the inside to match the inside colour of the box. All inside of the cabinet boxes to be finished with off white liner laminate of merino of greenlam laminated pasted using SWR D3 adhesive of pidilite only, heat processed using roller heat press machine to get better finish long sustenance. Four shelves placed on standard shelf pins of ebco/ hettich which should be adjustable to alternate heights if needed, Hardware set to include 110 degree opening self closing box hinges in post form laminate finish with shutters fixed with hettich hinges and laminate of Greenlam/ Merino make. Item also includes mini-fix fixture of hettich company, lock and angular bolt of ebco/hettich company. All screws to be used in cabinet should zinc and nickel coated. Curing/ protection of the cabinet facia must be ensured after installation during the interior works period of edisha centre. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing senior executive modular table of size 2100mmX900mm X750mm made out of full round post formed Table top made of 25mm thick HDF/MDF/Plane Partical board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only. Edges of table top shall be provided with machine pressed PVC edge banding 0.8mm thick in matching colour. Table understructure with 25mm thick HDF/MDF/Plane Partical board legs panel and modesty panel (upto 750 mm height) shall consist of standard 18 mm MDF board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only. All edges of the understructure to be provided with machine pressed PVC edge banding 0.8mm thick in matching colour Discreet/ concealed proprietary fixtures to be used at joints, with three drawer pedestal Width of drawer unit shall be of standard size of 450mm. Drawer tray shall of 18 mm thick made of 18mm thick MDF board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only, heat processed using roller heat press machine to better finish and long sustenance construction completely (bottom included) of size suitable to accommodate telescopic slides for smooth operation All visible edges of drawer trays shall have 0.8 mm thick edge banding to match the colour of the fascia. Inside edge of trays shall have 0.8mm thick PVC edge banding to match the colour of the tray. Front Central lock to be provided for locking all drawers, Table top to be provided with ABS wire manager at designated location as per pre-approved sample,Plastic keyboard pullout tray made up of durable ABS (Acrylonitrile Butadiene Styrene) materialprovide with sliding telescopic channels. (All work completed in all respect to the satisfaction of Driisya engineer incharge.. ( For Officers)

Providing and fixing senior executive modular table of size 1500mmX750mm X750mm made out of full round post formed Table top made of 25mm thick HDF/MDF/Plane Partical board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only. Edges of table top shall be provided with machine pressed PVC edge banding 0.8mm thick in matching colour. Table understructure with 25mm thick HDF/MDF/Plane Partical board legs panel and modesty panel (upto 750 mm height) shall consist of standard 18 mm MDF board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only. All edges of the understructure to be provided with machine pressed PVC edge banding 0.8mm thick in matching colour Discreet/ concealed proprietary fixtures to be used at joints, with three drawer pedestal Width of drawer unit shall be of standard size of 450mm. Drawer tray shall of 18 mm thick made of 18mm thick MDF board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only, heat processed using roller heat press machine to better finish and long sustenance construction completely (bottom included) of size suitable to accommodate telescopic slides for smooth operation All visible edges of drawer trays shall have 0.8 mm thick edge banding to match the colour of the fascia. Inside edge of trays shall have 0.8mm thick PVC edge banding to match the colour of the tray. Front Central lock to be provided for locking all drawers, Table top to be provided with ABS wire manager at designated location as per pre-approved sample,Plastic keyboard pullout tray made up of durable ABS (Acrylonitrile Butadiene Styrene) materialprovide with sliding telescopic channels. (All work completed in all respect to the satisfaction of Driisya engineer incharge.). ( For Brefing Room)

Providing and fixing modular conference table of size 4875mmX1800mm X750mm with following details. TABLE TOP: Table top made of 25 mm thick Plain Particle board/MDF/HDF, Table top outer edge on user side will bull nosed/Full Round profile machines post formed with lower edge post-form laminate folded to 25 mm, table top width of 1800 mm all finished with approved shade of post forming laminate of Merino/ Greenlam, roller heat pressed using SWR D3 adhesive of Pidilite to better finish and long sustenance construction of the structure of table. Intermediate edges of table top will be provided with machine pressed PVC edge banding 1mm thick in matching colour of Rehau company discreet/concealed proprietary fixtures to be used at joints and all remains user accessed edges to be provided with machine pressed PVC edge banding 0.8mm thick in matching colour of Rehau company. MODESTY: Table understructure with modesty panel (upto 750 mm height) shall consist of standard 18mm thick Pre- laminated MDF/ HDF/HDHMR board, finished with both side laminate of approved shade of post forming laminate of Merino/ Greenlam roller heat pressed using SWR D3 adhesive of Pidilite to better finish and long sustenance construction of the structure of table. Intermediate edges of under structure modesty will be provided with machine pressed PVC edge banding 0.8mm thick in matching colour of Rehau company discreet/ concealed proprietary fixtures to be used at joints and all remains user accessed edges to be provided with machine pressed PVC edge banding 0.8mm thick in matching colour of Rehau company Discreet/concealed proprietary fixtures to be used at joints.LEGS: All legs of the table to be made out of 25mm thick Pre laminated MDF/HDF /Pre laminated Particle board, finished with both side approved shade. Intermediate edges of legs will be provided with machine pressed PVC edge banding 0.8mm thick in matching colour of Rehau company discreet/concealed proprietary fixtures to be used at joints and all remains user. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing reception Desk of size 2400mmX 2400mm X 1000mm. Double top desin, upper top made out of 12 mm corian finish and lower top finish with approved shade of laminate. All structure made of 18mm thick HDHMR/HDF/MDF board, laminated with approved shade of post forming laminate of Merino/ Greenlam fixed using SWR D3 adhesive of pidilite only. All edges of the understructure to be provided with machine pressed PVC edge banding 0.8mm thick of Rehau Company in matching colour Discreet/ concealed proprietary fixtures to be used at joints, with two number of three drawer pedestal Width of drawer unit shall be of standard size of 450mm. Drawer tray shall of 18 mm thick made of 18mm thick HDHMR/HDF/MDF board, laminated with fabric colour liner sheet, fixed using SWR D3 adhesive of pidilite only, heat processed using roller heat press machine to better finish and long sustenance construction completely (bottom included) of size suitable to accommodate telescopic slides for smooth operation All visible edges of drawer trays shall have 0.8 mm thick of Rehau Company edge banding to match the colour of the fascia. Inside edge of trays shall have 0.8mm thick PVC edge banding to match the colour of the tray. Front Central lock to be provided for locking all drawers. Lower Table top to be provided with ABS wire manager at designated location as per pre-approved sample,Plastic keyboard pullout tray made up of durable ABS (Acrylonitrile Butadiene Styrene) materialprovide with sliding telescopic channels. (Supply as pre-approved design by Driishya Engineer Incharge).

Supply of conference chairs with revolving chairs with push back, net seat and back. Comfortable for long seating situations. (All work completed in all respect to the satisfaction of Driisya engineer incharge.).

Supply of Executive chairs of SM/Ergo Company with approved shade of crape fabric/ lathe-rite, including hydraulic, pushback, revolving system. (SAll work completed in all respect to the satisfaction of Driisya engineer incharge.).

Supply of workstation chairs of SM/Ergo Company with approved shade of crape fabric/ leatherette, including hydraulic, push-back, revolving system, provided to nylon net backing for better comfort.All work completed in all respect to the satisfaction of Driisya engineer incharge.

Supply of visitor chairs of SM/Ergo Company with 3 layer chrome ms pipe made, seats finish in approved shade of laterite.All work completed in all respect to the satisfaction of Driisya engineer incharge.

Supply of 3 seater sofa, with approved shade of fabric and laterite , with structure of 3 layer chrome ms pipe made. Using foam feather foam/ sleep well and acrylic wool of Religare, laid and pasted of acrylic supports belts and GI coated zig-zag springs. For Reception Areae. (All work completed in all respect to the satisfaction of Driisya engineer incharge.).

Providing and fixing centre table in Reception Area. Size 36”X24” (SAll work completed in all respect to the satisfaction of Driisya engineer incharge.).

Supply of Mobile CPU trolley of size 220X250X250 mm made up of CRCA ‘D’ grade MS duly powder coated with provision for height & width adjustment (coating thickness 50 to 60 micron) of Ebco/Hettich make. (All work completed in all respect to the satisfaction of Driisya engineer incharge.).

Supply of blackout roller blinds to have coated back with a unique blackout coating which could provides high levels of opacity of external lights of vista levolor company complete fitted at site in all respects i.e transportation, fixing with all zinc and nickel coated accessories and curing with PV sheets to avoid dust to settle during the works at site. (All work completed in all respect to the satisfaction of Driisya engineer incharge.).

Providing and fixing of PVC/UPVC pipe internal fitting and connecting it to the roof top water tank and 3"- 4" drain pipe to the outer wall the building. (for 4 block of washroom - New Public Toilet, ChairmanOffice, Reception Area,1st Floor ) (AREA FOR BILLING: Area to measured/Counted for billing is WC+Urinal + Washbasin+Wall Angle+Tap+) All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :All work completed in all respect to the satisfaction of Driisya engineer incharge.

Powder coated aluminium (minimum thickness of kg powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.All work completed in all respect to the satisfaction of Driisya engineer incharge.

Pre-laminated particle board with decorative lamination on both sides

With float glass panes of 6 mm thickness (weight not less than 15 sqm 168 923 1091 kg/sqm)

Providng and fixing all fitting required for aluminum doors complete in all respect .

Supply of name plate . (All work completed in all respect to the satisfaction of Driisya engineer incharge)

Providing and fixing 36watt 2’X2’ LED bright ceiling lights of Havells/Anchor/GM or equivalent company. Recess mounting luminaire with high brightness LEDs to give glare free light Delivers higher lumens while consuming less power & provide excellent illumination. (All work completed in all respect to the satisfaction of Driisya engineer incharge.

Supply of 5 Kw. stabilizer units of skybird or equilent company. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Split Type AC instalation charges.

Providing and fixing copper pipe for split AC Units with double insulation.

Supply and installation drain pipe of split AC units with insulation.

Supply of white powder coated metal AC stands with required fasteners etc.

Supply and installation D-Link Switch 24 port gigabit for computer networking.

Supply and installation D-Link Patch panel 24 port for computer networking.

Supply and installation Patch Cord.

Supply of AC units 1.5 ton 3 star split type AC of Blue Star/Daikin / Voltas Company. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Supply of AC units 2 ton 3 star split type AC of Blue Star/Daikin / Voltas Company. All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and fixing of wall mounted fan of reputed make (All work completed in all respect to the satisfaction of Driisya engineer incharge.

Providing and Fixing 15 mm thick densifled tegular edged eco friendly light weight calcium silicate false celling tiles of approved texlure of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising@ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws@ 230 mm interval and laying 15 mm thick densifled edges calcium silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixlures, smoke detectors etc., wherever required. Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ·r, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.