Chaudhary Ranbir Singh University Tender

Supply and installation of WORK STATIONS - 900W x 600D Providing and placing Tile based modular workstation, with partition thickness as 50-60 mm and ht - 1200 including powder coated aluminium trims. Tiles on main spine: Combination of top tiles are PLB/fabric tackable/whiteboard tile. Bottom tiles - Plain metal. FIN: 50-60 mm thick panel formed out of blocks which are 2x9 mm thick PLB boards wrapped with laminate at intermediate block and top block. Bottom block is finished in metal finish. SPLIT Tiles on main spine: Combination of two finishes for the top tiles on the user side shall be decorative laminate/white board. System shall have 120 mm high powder coated standalone panel legs to give the system an elevated look. INTERMEDIATE BLOCKS on main spine Intermediate blocks are given in DL + DL finish. (Decorative laminate) Wire Management through main spine- Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. Necessary cut outs for switches and switches as per site requirement will be provided. Cost of wires not to be considered in furniture. Work surface - Made of 25 mm thick pre-laminated particle board confirming to IS:12823 interior grade with post forming on front only of size 900 mm w x 600 mm. PVC edge binding tape 2 mm thick will be provided in balance sides. Note: All partitions and side panels have leveling screws for adjustment in case of Uneven floor to take care of +/- 20 mm of uneven flooring. Raceway:-The raceways are made out of 0.8 mm thick CRCA & powder coated. The electrical raceway can be provided below worktop or above worktop, these are hook on type which will be mounted on the verticals. The skirting/data raceway is hollow and will be mounted on the raceway channels CPU trolley Fixed Type: CPU Trolley: the metal Tray is made of 1.0 mm thick CRCA Sheet and Side support is made of 0.8 mm thick CRCA Sheet. On Wall Side (With common side partition sharing)

Back to Back (With Common side partition as well as common central)

Chairs for Computer Lab Work Stations without arm: Specifications Upholstered with fabric, High resilience polyurethane foam, Fixed type mechanism, Tubular frame. Back: (W) 39.0 cm x (H) 38.0cm, Seat: (W)45.0cm x (D) 42.0cm Overall Dimensions of Chair Scat Height -45.0cm. Height -81.5cm. Width & Depth of Chair as measured from pedestal - Width-56.0 cm and Depth-54.0 cm. The seat shall be made from 1.2 +/- 0.1cm. thk. hot pressed plywood and back shall be injection moulded from black Co-polymer Polypropylene upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of seat shall be 45.0cm (W) x 42.0cm. (D) and of back shall be 39.0cm(W) x 38.0cm (H). The seat and back covers shall be injection moulded in black Co-polymer Polypropylene. The HR polyurethane foam shall be moulded with density 45 +/-2 kg/m3 and hardness load 162 kgf as per IS:7888 for 25% compression. The fixed type mechanism shall be without back tilt. The tubular frame shall be made up of dia 2.54 ±0.03cm. x 0.2 +0.016cm.thk. M.SER.W. tube and black powder coated (DFT 40-60 microns). The overall dimensions of chair shall be Seat Height - 45.0cm, Height -81.5cm, Width & Depth of Chair as measured from pedestal - Width-56.0 cm and Depth-54.0 cm.