Chaudhary Charan Singh Haryana Agricultural University Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) (HSR 6.1.6)

Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) 40mm thick (HSR 6.8.2)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1. 7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. (HSR 6.10)

Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. (HSR 6.13)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: (HSR 6.14.1) 1 : 1. 5: 3 ( 1 cement : 1. 5 coarse sand (zone-Ill): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size) (HSR 6.15.1)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete (HSR 6.30.1)

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies (HSR 6.30.3)

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) (HSR 6.30.4)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers (HSR 6.30.5)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts (HSR 6.30.6)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diaMeters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D kg or more. (HSR 6.33.6)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.complete in all respect above plinth level. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D or more (HSR 6.34.6)

Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.21.2)

Brick work with common burnt clay non-modular bricks of class designation 10 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.22.2)

Painting top of roofs with bitumen of approved quality @ 17kg per 10 impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete With residual type petroleum bitumen of grade VG -10 (HSR 9.10.1)

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1: 3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay non-modular brick tile of class designation 10 (HSR 9.11.1)

Providing gola 75x75 mm in cement concrete 1: 2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (HSR 9.17.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR 9.18)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing periMeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and30 mm long, the periMeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of periMeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charae but excludina the cost of painting with 12.5 mm thick tapered edge gypsum moisture resistant board (HSR 9.46.3)

Providing and Fixing 15 mm thick densifled tegular edged eco friendly light weight calcium silicate false celling tiles of approved texlure of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising@ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws@ 230 mm interval and laying 15 mm thick densifled edges calcium silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixlures, smoke detectors etc., wherever required. Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ·r, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. (HSR 9.48) Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection 85%, noncombustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/mK.

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diaMeter (HSR 9.57.2)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend (HSR 9.58.5.2)

Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms. (HSR 9.61)

Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling. (HSR 10.1)

Providing and laying cement concrete pavement with 1: 2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. (HSR 10.16)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (HSR 10.63.2)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm (HSR 10.67.2)

Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm (HSR 10.70.2)

12 mm cement plaster of mix : 1 :4 (1 cement: 4 fine sand) (HSR 11.5.3)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1 :4 (1 cement: 4 fine sand) (HSR 11.6.1)

Pointing on tile brick work with cement mortar 1 :3 (1 cement : 3 fine sand): Flush/ Ruled/ Struck or weathered pointing (HSR 11.26.1 )

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (HSR 11.58)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer (HSR 11.64.1)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 litre/1 O sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (HSR 11.95.1)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 x 10 mm (HSR 12.99.5)

Providing and fixing of roller blinds on windows complete with material and labour complete with push up & down arrangement as per approved design /colour and Engineer-in-charge. (HSR 12.114)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) (HSR 12.157.1.2)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron(HSR 12.157.2.2 )

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides (HSR 12.158.2 )

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (HSR 12.159.2)

Providing and fixing PVC wall paneling consisting of 7mm thick cactus make hollow PVC section, PVC U section beading of size 25mmx8mmx12mm and PVC angle nosing of size 25mmx25mmx1.5mm including cost of PVC gutties, screws, jointed with polyfix (instant glue), complete in all respect as per drawing or as directed by Engineer-in-Charge (NS)

Providing and fixing factory manufactured cement concrete 1:2:4 kerb finished smooth and of size 1’-0” x 1’-0” x 0’-6” of required shape and design fixed at ground level along with road parking, complete in all respect as directed by the Engineer-in-Charge but excluding cost of cement pointing. (NS)

Supplying and fixing readymade white writing board of PRESKO make with delux frame or any other similar brand, fixed in position, including wooden gutties, nails and screws, etc., complete in all respects as per drawing and design (NS)

Electrical work 49 to 119:- Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group A (HSR 23.4.1.1)

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group A (HSR 23.4.4.1)

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling, including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group A (HSR 23.4.5.1)

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 2.50 Sqmm(1.1.80mm) (HSR 23.5.6.2)

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 4 Sqmm(1/2.24mm) (HSR 23.5.6.3)

Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. (HSR 23.7.6.2)

Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 40 mm dia. (HSR 23.7.6.4)

Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cmlong M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. (HSR 23.8.4)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 1 & 2 Modules including combined plate for Telephone and data (HSR 23.8.10.1)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 12 Modules (HSR 23.8.10.6)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Step type Fan Regulator 2 modules 300 watt (HSR 23.8.11.7)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Telephone Socket outlet modular type (HSR 23.8.11.8)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate (HSR 23.8.11.10)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type (HSR 23.8.11.11)

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA (HSR 23.22.1.9)

MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP (HSR 23.22.2.1)

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) (HSR 23.22.4.5)

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 8 way ( 8 incoming 3phase*8 outgoing) (HSR 23.22.4.7)

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole (HSR 23.22.5.1)

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCB's FOUR POLE (HSR 23.22.5.8)

Supply of GI pipe (B-Class) for suspension rod of ceiling fan including threading if required. 15 mm dia (HSR 23.23.2.1)

Supply and erection of blanking sheet in existing distribution board. (HSR 23.22.7)

Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. 2 pair telephone wire (HSR 23.23.8.1)

Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required (HSR 23.23.9)

EARTHING AND LIGHTENING ARRESTOR Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. (HSR 24.1.1)

Extra for using salt and char coal/coke for pipe earth electrode as required. (HSR 24.1.2)

Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including each 3772 accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. (HSR 24.1.3)

Extra for charcoal or coke and salt for G. I. plate or copper plate earth electrode. (HSR 24.1.5)

Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required. (HSR 24.1.7)

Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. (HSR 24.1.8)

Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required. (HSR 24.1.11)

Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. (HSR 24.1.13)

Laying of underground cable 0. 75 metre below ground level covered with sand and bricks including excavation and refilling of trenches.:- 16 Sq mm to 35 sqmm 2 to 4 Core (HSR24.2.2.2)

Laying of underground cable 0. 75 metre below ground level covered with sand and bricks including excavation and refilling of trenches.:- 50 Sq mm to 150 sqmm 2 to 4 Core (HSR 24.2.2.3)

Laying and fixing of cable on surface/ cable tray etc as required: 16 Sq mm to 35s qmm 2 to 4 Core (HSR 24.2.5.2)

Laying and fixing of cable on surface/ cable tray etc as required: 50 Sq mm to 150s qmm 2 to 4 Core (HSR 24.2.5.3)

Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50s qmm Cable 2 to 4 Core (HSR 24.2.7.3)

Supply and erection of suitable compression type brass cable glands for underground Cable :- 70s qmm to 95s qmm Cable 3 to 3½ Core (HSR 24.2.7.4)

Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work . 25sqmm (HSR 24.2.8.5)

Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work . 50sqmm (HSR 24.2.8.7)

Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work 95sqmm (HSR 24.2.8.9)

S/E of underground cable XLPE CABLE aluminium conductor armoured .(NS) 25 sqmm 4 core cable (armoured)

S/E of underground cable XLPE CABLE aluminium conductor armoured .(NS) 50 sqmm 4 core cable (armoured)

S/E of underground cable XLPE CABLE aluminium conductor armoured .(NS) 95 sqmm 3.5 core cable (armoured)

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod etc. {NS} i) 1200mm sweep. Make: Usha, Orient, Crompton.

S/I/T/C of push ON/OFF type 25 A modular type motor starter switch (white color) for AC's including the cost of petty material required to compete the job upto entire satisfaction of Engineer-in-charge. (NS) Make;- Schneider/Crabtree/Athena

S/E of surface/wall mounted ≤20W integrated LED 4 feet fitting with Epoxy Powder coated white/Grey extruded aluminium channel housing for efficient heat dissipation. Total system lumen of 20 watt LED should be ≥ 2200 or above in cool day light (5700K to 6500K), Power factor 0.95, CRI 80, Average life 50000 hours. Complete with mounting Brackets & accessories as required with connections(Industrial) Make: Philips, Havells, Wipro, Bajaj. (NS)

S/E of recessed type 42 Watt full window glare free opal diffuse LED Panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 5100 or above in cool day light (5600K to 6500K), Power factor 0.95, CRI (Ra) 80, LED Lamp efficiency ≥ 100 lm/w, Average life 50000 hours, complete with all accessories as required with connections (Industrial) Make: Havells, Philiphs, Bajaj (Industrial) (NS)

Providing and installing split type air conditioners, five star rating inverter type with copper coils 2.0 ton capacity ± 10%) fitted with super tropical - DC PAM inverter- return cooled - rotary compressor operating on refrigerant R-410-A/R-32 suitable for wall mounting confirming to IS : 1391 (part-2)/92 (except power consumption norms) with upto date amendments, suitable for operating on 230 volts, 50 Hz single phase A.C. supply having following specifications:-(i) Cooling coil row -3 Each.(ii) Air flow (CMH)1100 -1450 cum/ hr.(iii) Sound level (H/M/L)- 41/38/34/25(silent mode)(iv) Louvers swing- 3D + 3D Auto etc. complete in all respect MAKE :- O General/Mitsubishi (Heavy Industries) (five star rating) Model as approved by the Engineer-in-Charge. (NS)

Providing and installation of automatic voltage stabilizer of 5.00 KVA capacity (heavy duty) copper wound 100 up voltatge complete in all respect. (NS) Make:-Voltstar,V-Guard,Microtek

Providing and fixing extra copper tubing/regrigerent pipe for above split air conditioners (if required) consisting of inlet, outlet pipes, insulation and electric wiring etc. as per requirement, complete in all respect beyond 4.0 metres length. (NS) NOTES :- INSTALLATION OF AIR CONDITIONERS INCLUDES:- 1. Mounting/ fitting indoor and outdoor units at their respective locations 2. Providing & laying refrigerant pipe line of four metres length and beyond (if required) and connecting both the units after drilling holes in the wall, if required. Thickness of the copper tubing shall not less than 0.80 mm. 3. Insulating the suction pipe with expanded polythene pipe tubing. 4. Providing & laying drain pipe to throughout the condensate water being formed in the indoor unit 5. Leak testing entire system 6. Charging refrigerant gas in the unit 7. Electric wiring ; suitable electric wiring and switch should be provided with in 4 metres of the location of the units as per requirement 8. PVC channels for concealing the pipes etc. 9. Refrigerant piping thickness- 18 guage (1 mm) (i) Liquid line :- 6.35mm (1/4") (ii) Gas line:- 15.88mm(5/8") 10. Providing and fixing 2.5 sqmm x 4 core coper wire sheathed for connections and communication between indore unit to outdoor unit. (NS)

Providing and fixing in position powder coated MS stands for outdoor units of air conditioners including suitable nuts & bolts etc. of best quality complete in all respect (NS)

Supply Installation testing & commissioning of Category 6 Patch Cord 6.5feet, including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/AMP/Molex/belden

Supply Installation testing & commissioning of 24Port loaded Straight Jack pannel, including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/AMP/Molex/Belden

Supply Installation testing & commissioning of 12U rack with front glass door lockable, Fans 90 Cfm 230 Vac, PDU Horizontal 5Amp with 6 Schokets, Cantilever Tray-1U, Horizontal PVC Cable Manager and Hardware front panel Mtg. including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/NETRACK/VPRO

Supply Installation testing & commissioning of AP Management License with 3 years comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : RUCKUS/CISCO/ARUBA

Supply Installation testing & commissioning of Indoor Access Point with secure Mounting Bracket and with 3 Year free comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specifications : The Access Point should have 2 auto MDX, auto-sensing 10/100/1000 Mbps RJ-45, with POE support on one port, and one USB port. AP should be IOT ready from day 1. The APs should support the IEEE 802.11a, 802.11b, 802.11g , 802.11n & 802.11ac Wave2 standards. It should support minimum 3 MU-MIMO clients simalteniously. The AP must support Dual Band Concurrent Operation - 2.4GHz and 5GHz. Should support 3 spatial streams on both radio bands for an aggregate capacity of 1.75 Gbps including 450Mbps on 2.4Ghz.The access points should be centrally managed. In some small isolated environments the AP should be able to function as a full-fledged stand-alone access point without the requirement of a controller.Security mechanisms should be in place to protect the communication between the Access Point controller and the Access Points.Since most radio interference come from the WLAN network itself the vendor should specify what mechanisms such as beam steering/ adaptive antenna technology/ beamforming are available in combination to focus the energy on the destination STA and minimize radio interference with the surrounding of the AP. The vendor should specify if the activation of such feature is still compatible with 802.11n spatial multiplexing. Since the WLAN network will be using an unlicensed band the solution should have mechanisms that reduce the impact of interference generated by other radio equipment operating in the same band. The access point should be able to detect clients that have dual band capability and automatically steer those client to use the 5GHz band instead of the 2.4GHz band.The antennas to be dual polarised and should be integrated inside the access point enclosure to minimize damage and create a low profile unit that does not stand out visually. The access point should support 802.1q VLAN tagging.The access point should support WPA2 enterprise authentication and AES/CCMP encryption. AP should support Authentication via 802.1X and Active Directory. Implement Wi-Fi alliance standards WMM, 802.11d, 802.11h and 802.11e .The Access Point should provide for concurrent support for high definition IP Video, Voice and Data application without needing any configuration. This feature should be demonstratable. AP should provide minimum 23 dBm Radio output power for 2.4Ghz and 5Ghz both. (EIRP should be limited as per govt regulation for indoor AP's).Should support Transmit power tuning in 1dB increments in order to reduce interference and RF hazards .Device antenna gain (integrated) must be at least 3dBi and should provide automatic interference rejection of about 10dB.Upto 16 BSSIDs per AP for multiple differentiated user services (e.g. voice). should support upto 500 clients per AP. Should support IPv4 and IPv6 from day one. The access point should support following security mechanism: WEP, WPA-PSK, WPA-TKIP, WPA2 AES, 802.11i. System should support Authentication via 802.1X, local authentication database, support for RADIUS and Active Directory.Mechanism for physical device locking using padlock /Kensington lock / equivalent. Operating Temperature: 0°C - 40°C, Operating Humidity: upto 95% non-condensing. Should be UL 2043 plenum rated and comply to WEEE/RoHS. Should be EN 60601-1-2 Medical compliant. (NS) (MAKE : RUCKUS/CISCO/ARUBA)

Supply, Installation, Testing and Commissioning of Interactive Flat Panel Wall Mount - Technology TFT LCD with DLED Backlit; Display size (diagonal) 86" or Higher. Aspect Ratio 16:09; Resolution 3840 x 2160 4K Ultra HD; Flicker Free Yes with Blue Light Filter; static contrast ratio 1200:1 (typ): brightness 350 nits:display clour 1.07B colours:input ports HDMI x 3:VGAx1;display portx1;audiox1;CVBS(AV);RS232x1;PC slotx2;Slotin for pc built inx1;Wifi module slot built in x 1;output port HDMI x1;audio (earphone out)x1;SPIDFx1;LAN RJ45 x1;USB3.0 type A x3;2.0 typeA x3;2.0 type B(for touch) x2 ;Speaker 16 w x2 ;Touch type :IR recognition;touch resolution:32767x32767,Touch point:20 points;writing :10 points;response time15ms;support:windows 10/windows8/windows7/windowsXP/Vista/LInux/MAC/ANdroid/wince/Chrome;embedded player CPU inbuilt Android Version:5.1;CPU:ARM quad core cortex A53 1.2Ghz;GPU ARM Mali-450 MP 4;Memory:2 GB;Storage:16GB eMMC;Networking:10/100M auto-identtification and DHCP;Anti Scratch-Anti Glare Minimum 7 H scratch resistant and anti glare ;mirror extending flexibility to allow content to be mirrored on two IFB simultanesouly through HDMI out.Save option built in save option directly to Google Drive and One Drive. QR Code Scan:In Android Mode should have File download feature in smart phone just by scanning the QR code. Email: In Android juts by pressing of a icon the email should get generated and it should have facility to get the annotation/session attached as PDFautomatically. Split Screen: Should have the feature, built-in facility to split the screen in 2,3,4,5 or max.6 for simultaneous function/working on various application at the same time from a single PC. Annotation/Writing: Should be able to write on a Blank screen and on any application -PPT, Word, Excel, PDT, Web Browser, Video etc. Floating Tool: Should have floating tools which should appear just by press of 2 fingers for writing/annotation. Recording: It should also have recording function of Audio and Video. Quiz Built in Tool to allow participants to submit answwers from their Smart Phones, Zoom Video Conferencing - Built-in PC with IFP Core i5, DDR4 8GB, 2.5",128 GB SATA S3 SSD, Network: Wireless 802.11; including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge(NS) Make: View Sonic/Samsung/Sony

S/I/T/C of Two-Way 4" Coaxial Ceiling Loudspeaker with Frequency Range: 74 Hz - 20 kHz, Power Capacity (low-Z): 60 W Cont. ProgramMax. SPL: 102 dB @ 1m ave., 108 dB peak, Nominal Impedance: 8 ohms (in irect/bypass 8Ω setting), 70V/100V Transformer Taps, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make:-Bose/JBL/Audio tek

Supply, Installation, Testing and Commissioning of Digital Podium – Material: Mild Steel; Should have Tray for Keyboard. ( Keyboard Dimension Standard Lenovo Keyboard); Should have built-in Visualizer and 19” Interactive Panel .It should also have the flexible options in sizes for the 19” or 21.5” Interactive Panel to fit in; Interactive Panel motorised positioning up and down as per the user convenience; Should have single Sliding tray to Protect the Interactive panel and for the controller;The top of the Podium should be wooden. Should have a space for the Desktop PC and for the equipments to fit in as per the International standards. Sliding Shelf 1) For Placement of extra laptop or Document 2) Drawer For Visualizer with Lock; Door Lock – Yes. Central Control System Should be able to control from the Controller with easy identified keys - Projector On Off , Motorised Screen Up & Down , Switching between PC, Visual Presenter and laptop, Volume Control. Front Panel should have- 17 Membrane keys for control, Power Plug 0f 220 Volt Power out for Laptop etc.,VGA Port X 01, 3.5mm Audio Input X 01,Network Port wired Internet x 01,USB X 02 Ports ,Ports for 6.35mm Microphone Input Back Panel of the Controller should have - Should have Projector IR Controller ,Should have 1 RS 232 Projector Control ,Should have 2 x 2 VGA matrix, Should have 2 HDMI Input and 1 HDMI Out, Should have 2 USB Ports for front, Connectivity, Should have Network Port for front connectivity, Should have2 Video In and 2 Video out, 2 Audio (Left) in , 2 Audio (Right) in, Should have 1 x Projector Power , 1 x Electric Screen Power; Built-in inputs on the left hand side : HDMI x 1, VGA x 1, USB Ports x 2, Power Plug x 1, Audio Mini In x 1, RJ 45 x 1, Microphone Input x 1, Video In x 1, Audio in ( Left and Right) x 2 Signal Switching :The Interactive Monitor touch should work independently for the both Laptop and PC. Whichever source is selected PC/Laptop when both are connected to the Podium the content should appear on Interactive Panel along with touch activated of the selected source, automatically without detaching or attaching a cable. CPU: Core i5 equivalent processor; Suitable express Chipset; 8GB RAM, 1TB HDD; OS: Windows 8 / 10; Keyboard and Mouse Built-in Audio Microphones: 1 x Gooseneck Mike: Frequency range 50 – 70000 Hz, Output Impedance at 1000Hz Should be rated at 150 Ω ; Dynamic range and 1kΩ load- 96.2dB ; Interactive Panel Panel Type;Active Matrix Color TFT; Display Size:19” or higher; Resolution: 1024 x 768 pixels; Brightness: 250cd/m2 or higher ; Contrast: 1000:1; Connectivity : RGB/VGA ; Interface: USB; including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge (NS) Make: ATDSC/LABWE/AHA

Power Mixer SITC of Powered Mixer ideal for installs with inbuilt Class D amplifier, Max. midband output power, 1 kHz, THD = 1%, dual channel into 4 Ω :2 x 450 W into 8 Ω: 2 x 270 W , also capable of Direct-Drive option for 100V speaker lines. Frequency response, -3 dB, ref. 1 kHz,Any input to any Mixer output 15–22000 Hz.Crosstalk, 1 kHz Amplifier Ch1/Ch2 -85 dB.5 MIC/LINE input channels with compressor / limiter and talk-over function, 3 Stereo Inputs including Jack, RCA and USB connectors, onboard player for MP3 or WAV audio files, high quality effects section with 32 editable presets, 3 Master outputs with 7-band EQ each and flexible signal routing options, delay line for Master-B (150 msec / 50m), Auxiliaries (FX, AUX) 1 Post, 1 Pre ,Input impedances MIC 2 kΩ CD 10 kΩ All other inputs 15 kΩ, headphones control, LPN speaker processing, , comprehensive protection package, , optional rack mount kit, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make: Bosch / Bayerdynamics/Senneheiser

SITC Speaker EN 54-24 Certified 20W wall mount speaker with excellent speech & High-fidelity music reproduction Max Power: 30W,Rated Power: 20Watts, Power Tapping:20/10/5/2.5W Effective frequency range(-10 dB) : 90 Hz to 20KHz SPL at rated power (1Khz at 1 m) 101 dB Opening Angle 1 KHz / 4 KHz (-6 dB): 174° / 136° (hor.) 127° / 141° (ver.) Woofer :- 5 inch ; tweeter 1inch; Cabinet and front grill :- Aluminium Operating Temp : -25°C to +55°C ; RH95% EN60065; UL 94 V0 ;  Water & Dust protection :- EN60529 IP 65, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make: Bosch / Bayerdynamics/Senneheiser

Wireless Lapel Mic SITC of Wireless Lapel Mic with Cardiod polar pattern for transmitter , Receiver & Transmitter frequency response 100Hz-18kHz or better,Receiver RF sensitivity 1.0 µV,Receiver Image rejection55dB,Receiver Dyanmic range 95dB and receiver  having 32 channels possible,Receiver S/N ratio 100dB A,distortion 1 %, Transmitter sensitivity - 5.6 mV/Pa,modulation:+/-40kHz, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make: Bosch / Bayerdynamics/Senneheiser

Wireless Handheld Mic SITC of Handheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity 1.0 µV,Receiver Image rejection55dB,Receiver Dyanmic range 95dB and receiver  having 32 channels possible,Receiver S/N ratio 100dB A,distortion 1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS)           Make: Bosch / Bayerdynamics/Senneheiser   

SITC of Dual Channel Power Amplfier - 300W Analog Input Signal to Noise Ratio (ref. rated power, 100V, 20Hz - 20kHz) at 8 ohms) 104dB Frequency Response (8Ω, 20 Hz - 20 kHz) +/-0.5dB Crosstalk (below rated power) 20 Hz to 1 kHz 80dB also shall have GPIO/AUX Port – Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make:-Bose/JBL/Audio tek

SITC of Wireless Presenter Set Microphone System, Carrier frequency range 500.1 MHz – 864.9 MHz, Switching bandwidth 30.5 MHz (depending on local regulations), Audio bandwidth 35 to 20,000 Hz, Signal to Noise 120 dB-A, Up to 16 pre-programmed frequencies per group, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make:-Bose/AKG/Audiotek

S/I/TC of 12x8 Digital Signal Processor with Digital link and AEC , 12 Analog Inputs (with 48v Phantom Power per Channel), 8 Analog Outputs, 12 Control Inputs and 6 Logic Outputs for GPIO Integration, Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain, Digital Input Impedance: 110 ohm (AES/EBU), 75 ohm (S/PDIF), Sample Rate: 48kHz or 96kHz, THD+N: -140dB, Maximum Analog Output Level: +19dBu, Frequency Response: 20Hz-20KHz (+0.5dB/-1dB), THD: 0.01% 20Hz to 20KHz, +10dBu output, Dynamic Range: 108dB typical, 22Hz-22KHz unweighted, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make:-Bose/BSS/AMX

All types of cables (Cat-6, HDMI, XLR/microphone cable of any length) and connectors required to complete the job in all respect i.e. connectivity of podium to IFP to delegate unit and viceversa to run all the equipments in tandem, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make: Krammer/Sommer/Belden/Bosch LBB 4116/00+LBB4119/00) / Bayerdynamics/senneheiser

SITC of Analog input expander 8 analog MIC/Line input,2×RJ45 digital audio bus port,Phantom power on all inputs, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. Make:-Bose/BSS/AMX (NS)

Supply Installation, Testing and Commissioning of POE Switch : 8 Port ,layer 2 with 8 Each.10/100/1000 basetx POE port with SFP port one no. dual personality GBE port for copper/fibre uplink.20 GBPS switching capacity,maximum power consumption 85 watt, including the cost of all petty material required to complete the job upto the entire satisfaction of Engineer-in-charge. (NS) Make : CISCO/Ruckus/HP

SITC of 5.5KVA 4.4KW online UPS With inbuilt isolation transfomer with 30 minutes back up time,DEFAULT: 192VDC, ADJUSTABLE : 216VDC,SINGLE PHASE WITH GROUND,19.2KHz for high side IGBT & 50Hz for low Side -IGBT,Input nominal voltage-19.2KHz for high side IGBT & 50Hz for low Side -IGBT,ACCEPTABLE VOLTAGE RANGE-165-285V AC,FREQUENCY RANGE-40Hz - 55Hz @50 Hz System,OUTPUT NOMINAL VOLTAGE-208V AC / 220V AC/ 230VAC,AC VOLTAGE REGULATION-+1% (battery mode),FREQUENCY RANGE-Mains Mode(Synchronized Range): 45Hz - 55Hz/ Battery Mode: 50Hz 0.1Hz,TRANSFER TIME-AC TO DC MODE-Zero,INVERTER TO BYPASS MODE-Zero,BYPASS TO INVERTER MODE-‹5ms,WAVEFORM-Pure Sinewave,EFFICIENCY-AC MODE/ BATTERY MODE-87%/ 91%,RECOMMENDED BATTERY TYPE-SMF Battery,BATTERY CHARGING AMP.-2/4/ 8 AMP (D efault : 8 AMP.),NO. OF BATTERIES-16-18 Each(26AH),INDICATORS-Line ,Battery,Bypass,Fault,LCD DISPLAY-LOAD LEVEL, BATTERY LEVEL, AC MODE, BATTERY MODE, BYPASS MODE AND FAULT INDICATORS,ALARMS-Battery Mode: Sounding every 4 Seconds ,Overload: Sounding twice every second,Low Battery: Sounding every second, Fault: Continuously Sounding,MANAGEMENT-RS-232/ USB & BMS and SNMP interface,Supports Windows@ 2000/2003/XP/Vista/2008/7/8, Linux and MAC.with connection cables,accessories,suitable powder coated rack Make:-Eaton,Emerson,Microtek ,(NS)