Bharat Electronics Limited Tender

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to and above plinth level 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in ll shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand).

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Analysis, Design, Engineering, Preparation of Detailed Drawings, Manufacturing, Fabrication, Supply, Loading, Transportation to site, Unloading, Erection of PEB (PRE-ENGINEERED BUILDING) SYSTEMS, consisting of Primary structural frames such as transverse rigid frames, L-type canopy rafters, lean to rafters and columns, secondary structural frames such as purlins, girts/runners, eave struts, sag rods, wind bracing, flange bracing, base angles & clips, etc., including finishing edges by grinding, fixing in line and level with temporary bracings, providing staging, scaffoldings & working platforms at all heights and removal of same after erection, including supply of anchor bolts, grouting of anchor bolts with high strength free flow nonshrink grout mix, preparing the surface for painting, surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease, ncluding providing and applying two or more coats of synthetic enamel paint over and above a coat of approved steel primer etc., including all labour, tools & tackles, scaffoldings, all complete as per tender drawings, scope of work, technical specifications and as directed by the Engineer-in-Charge.(Basic rate of Steel is considered as Rs.65.00 per kg)

Providing and fixing not less than 0.55 mm thick Track deck 1000mm wide Hi-Rib- 100 Galvalume high tensile cold rolled steel sheets in roofing and cladding of Taurus blue or any other approved colour and in required lengths having a yield strength of 550 M Pa as per AS 1397 having Galvalume coating class AZ 150 (minimum 150 gm. per Sq. meter total zinc- aluminum alloy coating on both sides). The sheets shall be fixed to the purlins with suitable over laps in longitudinal and lateral directions and by providing Self fit fasteners along with EPDM washers and Polysulphide sealant as per manufacturers specifications. (Note- actual area of sheets as laid will be measured for payment.)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more (Basic rate of Steel is considered as Rs.65.00 per kg)

Providing over roof trusses /purlins wind turbine air ventilators of Airer India make or approved equivalent made out of aluminium rotor and stainless steel shaft/ball bearing having a rotor diameter of 495 mm and 266 mm height and of weight 1.5 kgs and fixing the same to roof trusses purlins with necessary fixtures ,gasket and making the roofing water proof including providing Sky pipe, all as per manufacturer specification and or as directed by the Engineer in charge. Sky pipe and wind turbine

Providing two or more coats of plastic emulsion paint of approved brand and manufacture to give an even shade on new work as per manufacturer's specification including a coat of approved primer and two or more coats of approved putty etc., complete

Providing and finishing walls with two or more coats of Acrylic Smooth exterior paint "Apex " of M/s. Asian Paints, or equivalent of required shade applied at 1.67 ltr / 10 sqm on new work over and including base coat of water proofing cement paint Snowcem plus or equivalent applied @ 2.20 Kg/10sqm etc., complete.

Providing and laying 80mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. (Basic rate of Interlock pavers is considered as Rs.525.00 per sqm)

Supplying and fixing motorised wind resistant rolling shutter of required size as per drawing and of approved make, viz Gandhi/Avians/Concord etc.The curtain shall be made of single skinned galvalume steel laths with natural finish interlocked together through their entire length along with Supplying, fixing, installation and commissioning of electrical motor of Europeon make suitable for raising and lowering of rolling shutters as per drawing along with complete accessories including gears, chain pulleys, connecting shaft, motor starter, push button, soft edge EPDM rubber for bottom profile, safety photocell etc.The rolling shutter shall be jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking, including the cost of ball bearings, mechanical device chain and crank operation and galvalume sheet top cover and motor cover etc.. complete. The rolling shutter shall be provided with brackets at both ends and MS storm guide channel having 75 mm (min) width including natural finish.The shutter shall be provided with operation swich from out side and push button from inside as per drawings and as per manufacturer's specifications. (Note: the rolling shutters shall conform to as per IS 6248 and to withstand wind speed of 33 meter per second for Bangalore conditions) complete. as per IS 6248 (Note: Electrical works such as conduits, cables, wires etc shall be measured and paid separately)

Providing and fixing MS gutter of suitable size as per design/drawing to the end of Galvalume sheet roofing made out of 2.0 mm thick MS sheet and providing epoxy painting after necessary sand blasting to the internal surfaces and providing two or more coats of synthetic enamel paint over a coat of zinc chromate primer to the outer surfaces of the gutters.Suitable size of MS clamps shall be fixed at every 2.00 m c/c to the purlins either by welding or with 8mm dia GI bolts /washers etc. of The welded joints of the gutter shall be treated with cold application epoxy coating and also shall be water tight (Note:Running length of the gutter shall be measured for payment) etc., complete.

Supplying and fixing of 4 way (4 + 12), Double door , horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

Supplying and fixing 5A to 32 A rating, 240/415 V, 10 kA, "C" curve, Single pole, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,Triple pole and neutral miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 20 mm size of steel conduit on the wall/column/ceiling/truss as the case may be along with accessories as surface/recess system including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit including associated civil works as required.

Supplying and fixing of 25 mm size of steel conduit on the wall/column/ceiling/truss as the case may be along with accessories as surface/recess system including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit including associated civil works as required.

Supplying and fixing of 20 mm size of medium class PVC conduit along with accessories on the wall/ column/ ceiling/ truss as surface/recess system including cutting the wall and making good the same in case of recessed conduit including associated civil works as required.

Supplying and fixing of 25 mm size of medium class PVC conduit along with accessories on the wall/ column/ ceiling/ truss as surface/recess system including cutting the wall and making good the same in case of recessed conduit with associated civil works as required.

Supplying and Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable including surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-A

Supplying and drawing/wiring of 3 x 1.5 sq.mm size of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing/wiring of 3 x 2.5 sq.mm size of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing/wiring of 3 x 4 sq.mm size of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing/wiring of 3 x 6 sq.mm size of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of 1 or 2 (75mm x 75mm) modules, GI box alongwith modular base & cover plate for modular switches in recess including associated civil works etc., as required.

Supplying and fixing of 4 module (125mm x 75mm) GI box alongwith modular base & cover plate for modular switches in recess including associated civil works etc., as required.

Supplying and fixing of 6 module (200mm x 75mm) GI box alongwith modular base & cover plate for modular switches in recess including associated civil works etc., as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc.as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying of 1100V grade FR power cable of 4core X 10sqmm size COPPER conductor, XLPE insulated, cores laidup, PVC tape inner sheathed, galvonise steel armoured, extruded PVC type ST2 sheathed as per IS:7098(part-1) 1988 or latest 2XFY and laying of the same in the existing trenches/ duct/ pipe/ on the wall with suitable clamps, dressing etc.or as directed.

Supplying and making end termination with brass compression gland and tinned copper lugs for 4core X 10sqmm size of PVC/ XLPE insulated and PVC sheathed copper conductor cable of 650V/ 1.1 kV grade as required.

Supplying of below mentioned specification LED luminaire & fixing of the same in the ceiling by providing required, clamps screws/ anchor bolt-nuts, washers etc., making electrical connections, earthing etc., as required/ directed by engineer-in-chargeType :- IP-65, wetherproof, Industrial type linear LED tube light luminaire with tube.Mounting type: Surface mounting type.System lumens :- Not less than 3600 lumens Rated power :- Not more than 40W Color temperature:-Not less than 6000K Housing :- Extruded powder coated aluminium/ polycorbonate housing. Diffuser :- Polycorbonate diffuser cover Driver :- In built Electronic driver Ref model :- Similar to BAJAJ: BJI 218 LEDPC or equivalent approved makes.

Supplying of below mentioned specification LED luminaire & fixing of the same in the ceiling by providing required down rod/ chain, clamps screws/ anchor bolt-nuts, washers etc., making electrical connections, earthing etc.as required / directed by engineer-in-charge.Mounting type:surface/suspended Type :- LED Highbay System lumens :-Not less than 27000 lumens Luminous efficacy :-Not less than 130 lumens/watt Input power :- Consuming not more than 80W Color temperature :-Not less than 5000K Housing :- Pressure die cast alluminium/ CRCA Diffuser :- Specially frosted polycarbonate diffuser Driver :- Electronic Ref model :-Wipro Enterprises :- Radial pro plus - LH09-921-090-50-V6 or equivalent in approved makes

Supplying of 600 mm sweep, continous/heavy duty, single phase, wall mounting oscillating type Air circuilator with accessories and installation of of the same by providing suitable grouting/ Anchor bolt&nuts, making electrical connections, earthing, testing etc., as required. The electrical connections shall be made by providing suitable size PVC insulated flexible copper cable from already provided ceiling rose as required.

Supply of materials, installation, testing and commissioning of Level-IV Lightning Protection System by using 40/16/10mm diameter aluminum rods & horizontal air teriminalsabove roof of the building. The work includes providing 8 nos. 2 mtrs hight size tapered aluminium air terminal rod, horizontal air teriminals, air terminal block,air terminal stand, and accessories, 8mm aluminium down conductors, around the periphery of building, etc. The work shall be carried out by using suitable hardware materials such as adhesive type base supports(stand fang) for conductor as well as air terminal holding/fixing, cross connectors, holders, expansion piece etc., 4 nos. of GI Earth plate system. The entire system shall confirm to level-IV LPS as per IEC62305 standard. Drawing of complete LA system shall be submitted for approval before taking up the works. Note:- Make: OBO-BETTERMANN / ERICO/ DEHN / ABB

Supply,installation,testing and commissioning of Microprocessor controlled Two loop analogue addressable Main Fire Alarm Control Panel with loop card, alarm facilities,hooter, fire / fault indications, audio visual signals,battery charger, printer and public address system interface system software, all as specified and or required etc., complete.Make: MORLEY-IAS

Supply,installation, testing and commissioning of Addressable uniform flat response/ multi sensor type Smoke sensor with base all as specifiedand/or directed etc.complete Make: MORLEY-IAS

Supply, installation, testing and commissioning of Addressable Manual Call Point / station with modules all as specified and/or directed etc., complete Make: MORLEY-IAS

Supply, installation, testing and commissioning of Short Circuit Isolator / fault isolator module all as specified and/or directed etc., complete Make: MORLEY-IAS

Supply, erection, testing and commissioning of addressable wall sounder / hooter (conventional sounder with module is not acceptable) with necessary modules all as specifiedand/or directed etc., complete.Make: MORLEY-IAS

Supply, installation, testing and commissioning of 2C x 1.5 Sq.mm PVC Armoured FRLS copper cable including juction boxes all as specified and/or directed etc., complete.Make: Deepanjan / Varsha / Finecore

Supplying and fixing of 25mm dia medium class PVC conduit pipes along with accessories in surface/ recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supply, erection, testing and commissioning of Music System with DVD/ CD/ MP3/ MP4 player, USB compatable and AM/ FM tuner for PA system including remote and other necessary accessories all as specified and/ or directed etc., complete.

Supply, erection, testing and commissioning of 6W wall mounted speakers with builtin 100 V line transformers and different power tapping all asspecified and/or directedetc., complete.

Supply and laying of 2 core (24/0.2) copper wire PVC insulated twisted and shieldedunarmoured wire for speakers /volume control switch of public address system suitable for laying in PVC conduit all as specified and/or required etc complete.,

Supply and fixing 19 mm dia 2 mm thick PVC conduit along with all accessories likebends,elbows, JBs,tees., in surface /recess including chipping the wall making good the same in case of recessed conduit all as specified and/or required and directed.

Supplying of 110mm outer dia(OD) HDPE pipe as per IS-4984 having wall thickness not less than 4.8mm and laying/drawing of the same in the existing trenches/ duct/ horizontal bore below earth as required and or as directed. The HDPE pipe shall be laid suitably for drawing of power/ communication cables on later date and end of the same shall be sealed suitably to avoid entering of soil/water inside the pipe.

Supply, Installation of Exit Sign Board (Left/Right) with 2 hrs backup of equivalent make such as fire lift/fire duct/ Hoseree/ Staircase signage etc of standard size as per conventional design/ colour code on 4mm thick foam sheet. The signage shall be either fixed on the wall with the help of screws/double tape or hanged from the false ceiling with the help of chain & screws etc complete in all respect.