Bharat Electronics Limited Tender

Disposal of moorum/building rubbish/ malba/similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in ll shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1cement: 4 coarse sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative laminationn on both sides

Providing and laying PVC flooring 2mm MAT including fixing with the Favi solution including reaparing the floor etc. complete

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3) : 1996 (Board with BIS certification marks)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. Complete 125 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. Complete 100X58X1.90 mm

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. Complete

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. Complete 125 mm

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size).

Steel reinforcement for RCC Work including straightening , cutting,bending,placing in position and binding all complete all levels. Thermomechanically treated bars of grade FE-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer & two coats of enamel painting as per direction of Engineer-in-charge all complete.

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Supply, loading, transportation, unloading at site and fixing in position approved quality, profiled, GALVALUME COLOUR COATED STEEL SHEETS 0.5mm thick RMP/SMP coated having a yield strength of 550 M Pa as per AS 1397 for gutter and rain water downtake (colour of sheet shall be single/multi-colour for the entire shed) including all necessary accessories and including cutting, mitering, laps, including necessary sheeting fasteners (approved quality anti-corrosive polymer colour coated to match roof & wall sheeting), self tapping sheet metal screws with metal and Neoprene washers on each crest of sheet, including all labour, tools & tackles, scaffoldings, all complete as per tender drawings, scope of work, technical specifications and as directed by the Engineer-in-Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying of LED Luminaire as per below mentioned specification of make/brand as per approved list in DTS and fixing of the same in the ceiling by providing required downrods / chainlinks / clamps, anchor bolt-nuts, washers, making electrical connections, earthing etc. as required / directed by engineer-in-charge. Type;- Recess mounting LED full diffuser luminaire. Mounting;- Recess mounting in 597*597mm size grid false ceiling. System Lumens;- Not less than 3600 lumens Systemrated power;- 230, 50Hz, 36Watts (+/- 10%) Colour Temperature ;- Not less than 5700K Housing;- White powder coated aluminium/ CRCA sheet; Diffuser- high optically efficient low glare diffuser; Driver-electronic driver pre-wired up to terminal block. Ref- Similar to WIPRO Elate : CRCO10R038HP57GL1.

Supplying and drawing 3x2.5 sq. mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.

Supplying and drawing 3x4 sq. mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required, including end connections to RJ 45 sockets including crimping, jointing etc. as required all complete. 4 pair UTP CAT 6-2 run of Cable

Supplying and fixing of 25 mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing 3 pin 5/6 amp modular socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supplying and fixing 1/2 modules (75mmx75mm), Gl box alongwith modular base & cover plate for modular switches in recess etc. as required

Supplying and fixing 6 modules (200mmx75mm), Gl box alongwith modular base & cover plate for modular switches in recess etc. as required

Supplying and fixing 6 pin 15/16 amp modular socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supplying and fixing 5/6 amp modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supplying and fixing 15/16 amp modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing 3 modules (100mmx75mm), Gl box alongwith modular base & cover plate for modular switches in recess etc. as required

Supplying and fixing 8 modules (125mmx125mm), Gl box alongwith modular base & cover plate for modular switches in recess etc. as required

Supplying installation , Termination, Labeling & Testing of dual (2) port flush type face plate with PVC / alumi back box.CAT0 make comscope/panduit-legrand/Dlink.

Supplying installation , Termination, Labeling & Testing of RJ-45 modular jacks, complaint with ISOIIEC11801 NSI/TIA/EIA-568, should accept solid 22-24 AWG diameter conductors with certified for UL94V-O rated, series connecting hardware standards. CAT6 (GREEN OR YELLOW) for data make comscope/panduit/legrand/Dlink.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 A,36KA,FPMCCB

Supplying and fixing of MCCB Enclosure/ DB on wall with nut, bolts, screws etc. as required and as directed by engineer in charge suitable for 125 A, 36 KA, FPMCCB, Ref: Legrand 507801 - Dpx3 160 Enclosure 4P

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying of 4 Core 70 sq. mm PVC Insulated and sheathed, XLPE Copper flexible cable 1100 V grade Ref. finolex 70 Sq.mm*4 Core Copper XLPE 1100 V Cable flexible

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE Copper conductor cable of 1.1 KV grade as required. 4 X 70 sq. mm each

Releasing and returning to stores the size of 3/4" to 1 1/4 " dia ( 20 mm to 32 mm ) pipe with all accessories viz., collars, bends, elbows and flexible wires inside pipes etc., below floor / ground or in existing duct as required. (Necessary excavation, refilling, etc., shall be measured and paid separately).

Releasing and stacking in the stores of existing LED Luminaires (down lighter/square modular / Tube light with batten etc) and all types of fans by disconnecting the power supply and sealing the ends with insulation tape and as the case may be as required and as directed complete.

Releasing and stacking in the stores of switch, sockets modular type or piano type or bell push etc of any make or any number of way by disconnecting the power supply and sealing the ends with insulation tape and as the case may be as required and as directed complete.

Releasing of various sizes of PVC insulated all type of copper/ aluminium wires sizes up to 6.0 sqmm from existing Condiut pipes along with accessories, coiling the released wires, transportation and returning the same to stores along with all the accessories as directed.

Releasing and stacking in the stores of all type of switch boxes / MCB DBs, MCB, all type (sheet steel/ wooden) enclosures by disconnecting the power supply and sealing the ends with insulation tape and as the case may be as required and as directed complete.

Dismantling and reinstallation of air curtain with nut, bolts, screws etc. as required with directions as per engineer-in-charge complete

Supply, fabrication, installation, testing and commissioning of factory fabricated GI sheet metal ducts of 20 Guage (Birmingham Gauge) (1.0 mm) and zinc coating not less than 120 g/m2 in accordance with approved drawings including necessary hangers, rubber gaskets, rivets, flanges, scaffolding required for work, etc., all as specified and/or directed etc.,complete Note: 1) The rate quoted for the GI ducting shall be including the cost of scaffolding, steel supports, nuts, bolts, etc. and the same will not be measured and paid separately.