Bhakra Beas Management Board Tender

First class burnt brick laid in cement sand mortar 1:6 in foundation and plinth. Pb-CSR-Ref.- 11.3(i)-T/R.

12.5 mm thick cement plaster 1:5. Pb-CSR-Ref. 15.10-T/R.

Providing and laying vitrified floor tiles of different sizes in light colour shades made using Double Charge technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete.(a) Size 600X600 mm Pb-CSR-Ref. 14.113(a)-T/R.

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled.(a) Doors of area 3 sqm and below. Pb-CSR-Ref. 8.26(a)-L/R

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece MS sheet outer box with slide plate and with stainless steel cover plate etc. complete as per the direction of Engineerin-charge.Pb-CSR-Ref. 17.48-T/R.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) : (a) For fixed portion and chawkhats. Pb-CSR-Ref. 17.45(a) -T/R.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) : (b) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug /neoprene gasket required. Pb-CSR-Ref. 17.45(b)-T/R.

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt). (ii) For shutter area above 0.50 sqm. Pb-CSR-Ref. 17.23(ii) -T/R.

Renewing glass panes with putty and nails wherever necessary. (a) Glass Panes weighing 8.44 Kg/sqm. Pb-CSR-Ref.31.5(a)-T/R.

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-In-Charge. Prelaminated particle board with decorative lamination on Both side. Pb-CSR-Ref. 17.46(ii) -T/R

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete. (b) I.S.I Designation No. II (size of door 701mm to 850mm) Pb-CSR-Ref.17.43(b)-T/R.

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : (A) 300mm x 16mm. Pb-CSR-Ref.17.49(A)-T/R.

R&R work of damaged boundary wall and providing of concertina barbed wire in office complex situated at 220 KV Sub-Station, BBMB, Dhulkote.

Dismantling brick work tile, masonry or tile lining. (b) in cement. Pb-CSR-Ref. 8.5(b)-L/R.

Scraping (e) Bricks dismantled from brick work in lime or cement. Pb-CSR-Ref. 8.31(e)-L/R.

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres. Pb-CSR-Ref.-6.6-L/R.

Cement concrete 1:6:12 (b) With stone aggregate 40mm gauge. (i) mixing by manual means. Pb-CSR-Ref. 10.8(b)(i)-T/R.

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth .Pb-CSR-Ref.-11.5- T/R.

12.5mm thick cement plaster in damp proof course 1:3 with two coats of bitumen at 1.65Kg. Per Sqm laid hot and sanded. (B) Horizontal. Pb-CSR-Ref. 15.49-T/R

115mm thick brick wall in cement sand mortar 1:4 without reinforcement in superstructure. Pb-CSR-Ref. 11.36-T/R.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. Pb-CSR-Ref.-11.6-T/R.

12.5 mm thick cement plaster 1:5. Pb-CSR-Ref. 15.10-T/R.

Finishing walls with cement based water soluble exterior paint such as snowcem, robbiacem etc. two or more coats to give an even shade .Pb-CSR-Ref.-16.13-T/R.

Cement pointing 1:3 deep variety. Pb-CSR-Ref.-15.60-T/R.

Providing and fixing concertina coil fencing with Punched Tape concertina coil 600 mm dia. 10 meters open able length (total length 90 m) having 50 nos. rounds per 6.00 meters length upto 3.00 meters height of wall with existing angle iron Y-shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, studtied with G.I. staples & G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete, as per directions of the E-I-C. with reinforced barbed tape (RBT)/ spring core (2.5 mm thick) wire of high tensile strength of 165 Kg/sq. mm with tape (0.52 mm thick) andweight 43.478 gm/meter (NS Item).

Steel work, fixed independently without connecting plates including cutting hoisting and fixing in position. (c) Tees angles & channels. Pb-CSR-Ref. 18.1(c)-T/R.

Drilling holes in girders. Pb-CSR-Ref.-26.2.

Applying priming coat with metal primer on new steel or iron work including preparation of surface. Pb-CSR-Ref. 16.20-T/R.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. Pb-CSR-Ref.-16.17-T/R

Welding by gas or by electric plant, including carriage to and from workshop etc. Pb-CSR-Ref.-18.28-T/R