Bhagat Phool Singh Mahila Vishwavidyalaya Tender
If you want to inquire about any e-tender the Haryana government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Haryana tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Haryana etender you're looking for. Read further to learn how to search and bid for etender Haryana.
Costs
EMD
₹ 98,100Document Cost
₹ 5,000Tender Fee
₹ 1,180
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_HRY_254788_1Bid Award Id
ViewTender No
127Tender Authority
Bhagat Phool Singh Mahila Vishwavidyalaya ViewPurchaser Address
-Website
http://etenders.hry.nic.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Dismantling old plaster or skirting raking out joints and cleaningthe surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (HSR-5.45)
1259.64
-
-
15 mm cement plaster on rough side of single or half brick wall of mix:1 :4 (1 cement: 4 coarse sand) (HSR-11.9.1)
668.95
-
-
12 mm cement plaster of mix 1 :4 (1 cement: 4 fine sand) (HSR-11.5.3)
723.32
-
-
Removing white or colour wash by scrapping and sand papering sqmand preparing the surface smooth including necessary repairs to scratches etc. complete (HSR-30.21)
3616.63
-
-
Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (HSR-11.58)
4339.95
-
-
Dismantling cement conglomerate / terrazzo floors 25 mm to 50mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge.. (HSR-5.42)
50.77
-
-
Providing and laying Baroda Green marble stone 17mm and above thick flooring included matching the grains of marble slab in any pattern as specified laid over 12mm thick cement sand mortar 1 :3 and jointed with white slurry mixed with pigment to match the shade of marble including rubbing and polishing. The rates are for all heights / storey. The sample shall be got approved from Engineer In Charge. (HSR-10.48)
50.77
-
-
Providing and laying Baroda Green marble stone 17mm and above thick in risers of step, skirting , dado, pillars and wall lining included matching the grains of marble slab in any pattern as specified laid over 12mm thick cement sand mortar 1 :3 and jointed with white cement slurry mixed with pigment to match the shade of marble including rubbing and polishing. The rates are for all heights / storey. The sample shall be got approved from Engineer In Charge (HSR-10.47 )
19.64
-
-
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. ( HSR-10.57).
50
-
-
Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (HSR. 10.58)
80
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of kg powder coating 50 micron) (HSR:- 12.157.1)
366.98
-
-
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. HSR:-12.158.2)
61.49
-
-
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than sqm 12.50 kg/sqm) HSR:-12.159.2)
56.13
-
-
Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm (HSR-12.98.1)
25
-
-
Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. Complete Twin rubber stopper (HSR-12.103.2
20
-
-
Providing and fixing aluminium e xtruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1 000 mm), with double speed adjustment with necessary accessories and screws etc. complete. HSR-12.89)
10
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coat applied @ 1.67 litre/ 10 sqm) on existing cement paint surface. (HSR-30.37.1)
756.66
-
-
Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws (HSR-12.36.1)
4.81
-
-
Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase (HSR:-9.17.1)
480.07
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level:1 :2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size) (HSR -6.14.2)
12.39
-
-
Pointing on tile brick work with cement mortar 1 :3 (1 cement : 3 fine sand): Flush/ Ruled/ Struck or weathered pointing (HSR-11.26.1)
4166.15
-
-
10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and obri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1 :3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay non-modular brick tile of class designation 10 (HSR-9.11.1)
125.41
-
-
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work (HSR-30.28.1)
320.9
-
-
Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISi : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. 1500 Ltr. capacity X3 [HSR 22.182].
4500
-
-
500 Ltr. capacity X5
2500
-
-
1000 Ltr. capacity X 5
5000
-
-
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore [HSR 22.103.1].
20
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore [HSR 22.107.1].
25
-
-
Providing and fixing Unplasticised PVC connection pipe with brass unions:45 cm length 20 mm nominal bore [HSR 22.101.2.2].
20
-
-
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore (HSR. 22.105.1)
15
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. . [HSR 22.15]
10
-
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia (HSR-22.14.2.2)
35
-
-
Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete 10 litre capacity - White (HSR-22.39.1)
5
-
-
S.C.I. gully or nahani grating 100 mm dia (B1120)
20
-
-
C.P. brass waste 40 mm (B1283)
20
-
-
8 mm dia C.P. Brass/ S.S. Jet with flexible tube up to 1 metre long with S.S. each 200 triangular plate for European type W.C. (B1079)
10
-
-
White plastic seat (solid) with lid C.P. brass hinges and rubber buffers (B1234)
10
-
-
G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of four lipped urinals (B1464) Jaquar Brand
10
-
-
M.S. Clamp RM106
30
-
-
G.I. inlet connection (B-1158)
50
-
-
Providing and fixing white vitreous chinaware battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. (HSR-22.46)
2
-
-
Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm Including both sides) comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary Intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall S.S screws. The work shall be carried out as per cifications, drawing and as per directions of the Engineer-in Charge. With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. (HSR- 32.42.1)
96.79
-
-
Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter (HSR-9.57.2)
50
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia Pipes (HSR- 22.85.2)
100
-
-
25 mm nominal outer dia Pipes (HSR- 22.85.3)
100
-
-
32 mm nominal outer dia Pipes (HSR- 22.85.4)
100
-
-
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) llnd course of 20 mm cement plaster 1 :3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) lllrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) lvth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen@ 1.7 kg/sqm). (HSR-28.14)
300
-
-
Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1O mm gap for thermal expansion. (HSR-9.58.4.2) 110x110x110 mm
10
-
-
Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. (HSR-9.58.5.2) 110 mm bend
20
-
-
Finishing walls with exterior grit ready mixed product with natural stone granules (N.S. items)
668.95
-
-
P & F water storage tank cover with all accesseries complete in all respect ( N.S. Items)
20
-
-
Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. TRIPLE POLE MCCB 16 to 100 Amp HSR- 23.22.1.3
10
-
-
TRIPLE POLE MCCB 400 Amp HSR- 23.22.1.7
2
-
-
Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR- 23.22.5.1
90
-
-
40 amp to 63 amp. MCB's FOUR POLE HSR- 23.22.5.8
36
-
-
Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Switch 5 amp. on existing sheet. HSR- 23.8.1.1
640
-
-
Wall socket 5 amp on existing sheet. HSR- 23.8.1.2
160
-
-
15 amp. switch on existing sheet. HSR- 23.8.1.3
54
-
-
6 pin 15 multi socket on existing sheet HSR- 23.8.1.4
54
-
-
Ceiling rose flush/surface type HSR- 23.8.1.5
580
-
-
Socket size rotary step type Electronic regulator for A.C. ceiling fan HSR- 23.8.1.13
380
-
-
Supply and Fixing Bakelite sheet on existing MS/GI/wooden/PVC box etc. including fixing with brass screws and washers. 15 mm thick HSR- 23.8.2.1
16000
-
-
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- Overall size 6sq.mm (2Core) Armoured (Loose) CSR - 34.10 (B)
420
-
-
Supply and erection of suitable compression type brass cable glands for underground Cable :- Upto 6 Sq mm cable 2 to 4 Core HSR- 24.2.7.1
48
-
-
Supply and erection of weather proof M.S. box size 20 cm * 15 cm * 10 cm covered with 3.00 mm thick M.S. sheet hinged cover, locking arrangement, housed in wall, including the cost of 1 no. 16 amp. 415 volts SPMCB and 2 no. 63 amp. 415 volts neutral links fixed on hard wood board/ 10 mm Bakelite sheet in the M.S. box including painting and necessary connections. HSR- 24.4.16
14
-
-
Replacement of ball bearing of a ceiling fan including greasing, re-assembling and testing etc. HSR- 23.15
360
-
-
Replacement of a fan condenser complete with connections and testing etc. 2 to 3.5 mfd. HSR- 23.17.1
380
-
-
Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) HSR- 23.5.6.1
640
-
-
1 run of Size 4 Sqmm(1/2.24mm) HSR- 23.5.6.3
280
-
-
1 run of Size 10 Sqmm(1/3.50 mm) HSR- 23.5.6.5
120
-
-
Supply and erection of U- PVC Trunking/Channel of following size including cost of fixing on wall, floor and ceiling etc. with required material complete the job in all respect up to entire satisfaction of the Engineer-in-charge of work. 50 x 50 mm HSR- 23.23.5.4
680
-
-
Supply and erection of MS saddle and clamps including the cost of all labour and material required to complete the job in all respect and upto entire satisfaction of the Engineer-in-charge of work. EL035
1140
-
-
Supply & erection 4 feet long LED batten tube light fitting 20watt. Make Havells, Model no. LUMILINEPLUSNEOBS20WLED865 S PCSSIND / Philips Make Model no. BN021LED40S-6500PSUGR & Make Wipro Model no. LL24-251-XXX-57-CD with warranty 2 Year & all latest updated specification complete in all respect up to entire stisfaction of Engineer in Charges of the work. (NS)
785
-
-
Supply & erection of LED false ceiling light (2x2) 36 watt. Make Havells Model no. PLANO2X2PLR36WLED 857S / Make Philips Model no. RC420BMLED34S6500PSDWH & Make Wipro Model no. CRC010R036HP57HEG2 with warranty 2 year & all latest updated specification complete in all respect up to the entire satisfaction of Engieer in Charges of the work. (NS)
138
-
-
Suppy & erection of LED flood light fitting 200watt. Make Havells model no. JETAIRISMAXFL200WLED757PWBLTG, / Make Philips Model no. BVP483PLED210X2CWSWBPSUP4145 & Make Wipro Model no. LF30-272-060-57-XX with warranty 2 year &all latest updated specification complete in all respect up to the entire satisfaction of Enginner in charges of the work. (NS)
14
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements