Archaeological Survey Of India Tender

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for foundations, footings, bases of columns etc. for mass concrete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level "Thermo-Mechanically Treated bars of grade Fe-500D or more."

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (Hot finished welded tube types)

Providing and fixing PUF (Polyurethane Foam) panel of core thickness 50mm having density 40 kg/cum and Thermal Conductivity at 10°C (Mean Temperature) 0.023 W/mk in roof complete with all accessories as per the direction of Engineer-in-charge.

Providing and fixing of Everest vertical fibre cement boards of thickness 75mm having density not less than 700-800 kg/cum along with GI channels and all accessories in walls and parititions complete as per the direction of Engineer-in-charge.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with Fully Perforated Gypsum Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge,(a) Fixed window / ventilator without mullion using R1 series with frame (33mm & above) x (35mm & above).

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge, (a) Casement window double panels with fixed mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles using R2 series with frame (39mm & above) x (39mm & above) & sash (39mm & above) x (60mm & above) & mullion (39 mm & above) x (60mm & above).

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge, (a) Casement door single panel with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides using R3 series with frame (55mm & above) x (50mm & above) & sash (55mm & above) x (85mm & above).

Providing clear/ frosted toughened glass of nominal thickness 8mm (weighing not less than 20 kg/sqm) for upvc doors and windows.

Providing and fixing white vitreous china pedestal type water closet (European type) with ISI marked white solid plastic seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing White Vitreous China Wash basin size 550x400 mm with C.I. brackets, 15 mm nominal dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge

Providing and fixing 15 mm nominal dia CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) of thickness 6mm adhered to the tiles by clear silicone adhesive complete.

Providing and fixing C.P. brass toilet paper holder

Providing and fixing 25 mm nominal dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Providing, laying and jointing 100mm nominal dia PVC drain pipes including all PVC fittings i.e. socket, bend, elbow, tee, coupling, flange etc. This includes jointing of pipes & fittings with rubber washer 3mm thick insert and one step PVC solvent cement direct in ground including excavation and refilling the trench as required.

Providing and fixing 100 nominal dia PVC P Trap or multi floor trap with necessary end caps with 100mm dia SS 304 grating including jointing with PVC drain pipe and fittings with rubber washer 3mm thick insert and one step PVC solvent cement.

Constructing brick masonry manhole with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

Providing and fixing 15 mm nominal dia C.P . brass bib cock of approved quality conforming to IS:8931

Providing and fixing 15mm nominal dia uplasticised PVC connection pipe 45 cm length with brass unions

Providing and fixing 25mm nominal dia ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

Providing and fixing 15 mm nominal dia C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Provision for purchase and installation of 25 ltr. Capacity geyser of reputed brand and manufacture along with SS connection pipes suitable for water heater.

Providing and fixing 600 mm long PTMT towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in size 600 mm x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

"Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work."

Finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Supply and fixing of 25mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (a) 4 x 1.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (b) 6 x 1.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (c) 8 x 1.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (d) 4 x 2.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (e) 6 x 2.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (f) 2 x 4 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required. (g) 4 x 4 sq.mm

Supply and fixing following size/modules, GI box alongwith modular base & cover plate for modular switched in recess etc. as required (a) 4 module (125mm x 75mm)

Supply and fixing following size/modules, GI box alongwith modular base & cover plate for modular switched in recess etc. as required (b) 8 module (125mm x 125mm)

Supply and fixing following size/modules, GI box alongwith modular base & cover plate for modular switched in recess etc. as required (c) 12 module (200mm x 150mm)

Supply and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. a) 5/6 A Switch

Supply and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. b) 15/16 A Switch

Supply and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. c) 3 pin 5/6 A Socket outlet

Supply and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. d) 6 pin 15/16 A Socket outlet

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, C curve including connections, painting etc. as required.

Supply and fixing of two module stepped type elctronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required

Supplying and fixing of pre wired, fluorescent fitting/ compact fluorsecnt fitting of all types, complete with all accessories and tube, LED light etc. directly on ceiling/ wall, including connections with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc as required.

Supplying and fixing 16 way (double door), single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of single pole and neutral in the existing MCB DB complete with connections, testing etc. as required.

Supplying and fixing 40A, double pole, 240V, isolator in the existing MCB DB complete with connections, testing etc. as required.

Supplying and fixng 40A, double pole, (single phase and neutral), 240V, residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Providing and laying earth connection from earth electrode with 4mm dia copper wire in 15mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and refilling as required.

Supplying and fixing of exhust fan upto 450mm sweep in the existing opening, including making good the damage, connection testing etc. as required.

Supply and Installation of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

20mm thick cement plaster of mix 1:4 (1 cement : 4 coarse sand) with curing complete.

Providing and laying brick tile edge in apron in composite mortar 1:4 (1 cement, 4 coarse sand) over bed of 20mm thick mortar including filling of joints.

Recess pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand) after raking, cleaning and washing of joints complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 mtrs openable length(total length 90m) having 50 nos round per 6 mtr length , up to 3 m height of wall with existing angle "Y" shaped placed 2.4 m or 3.00m apart and with 9 horizontal R.B.T reinforced barbed wire, stud tied with G.I stales and G.I clips to retain horizontal , including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of engineer-in-charge, with reinforced barbed tape (R.B.T)/ spring core (mm thick) wire of high tensile strength of kg/ sq.mm with tape (mm thick) and weight 43.478 gm/mtr ( cost of M.S angle, C.C block shall be paid separately)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Supplying and laying of 63mm dia (OD-63mm & ID-51mm nominal) size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

Supplying and drawing PVC insulated Type A (4+1) RG59 coaxial copper CCTV camera cable with data transfer speed of 6 gigabits per second in the existing surface/ HDPE conduit as required

Supply and installation of Hikvision 5 MP IP Bullet Cameras with 4K resolution, 3D Digital Noise Reduction, Aperture F2.0, IR range up to 30m with protection rating of IP67

Supply and installation of 16 channel 5 megapixel and 8 TB Sata Hard Disk Digital Video Recorder connectable to H.265+ IP Cameras and HDMI output at up to 4K (3840x2160) resolution.

Supply and installion of 43" LED TV of reputed brand i.e. Samsung, Sony, LG with 4K (3840 x 2160) resolution and 60Hz refresh rate and HDR support for use with CCTV cameras.

Supplying and installing Air Conditioner (Split 1.5 Ton and 5 star energy effieciency rating) of reputed brand of approved make along with all AC fittings and copper connections as required.

Providing and fixing ACP sheet (High Quality) of thickness 6mm in panelling of doors