Pradhan Mantri Gram Sadak Yojana Tender

Diversion of water course, providing Earthen bund with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a all lead as per Technical Specification

Providing flood gauge marks on substructure as per design including painting complete.

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Sandy Material

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Depth upto 0 to 3m. below GL

Earthwork in excavation for structures as per drawing and technical specifications including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Depth upto 3 to 6m. below GL

Earthwork in excavation for structures as per drawing and technical specifications including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto all lead & lift , dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary rock (not requiring blasting)

Providing concrete for plain concrete in open foundations complete as per drawings and technical specifications II P.C.C grade M 15 ( 1: 2.5: 5)

Providing and cast in situ controlled cement concrete of M-35 grade as per relevent code for reinforced cement concrete with 20mm down graded crushed stone aggregates of required size in foundation of pier abutment For Pile Cap etc. & Sub-structure including form work shuttering and supporting arrangement (excluding cost of reinforcement ) and transporting concrete from batching plant by transit mixture, placing it in position, Compacting with needle Vibrator including Curing with all labour, material, machinery, all lead, lift etc complete as per drawing and Technical specification.

Providing concrete for reinforced concrete in open foundations complete as per drawings and technical specifications II R.C.C grade M 25

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202 3) The work shall be done as per execution drawing.

Empty boring through all sorts of strata for providing 1.20 m dia RCC bored piles to required depth including flushing necessary casting pipe with all plants and equipments as required as per detailed specifications for Abutment and Piers (Excluding Concrete & Reinforcement)

Carrying out load test on any pile as per standard procedure laid down in the IS:2911 specification including construction of test cap, dismantling the cap after test and cleaning the site and maintaining complete records of load settlement as directed by Engineer and as per specification, and submission of records. a. Load testing of foundation piles including loading with necessary kentledge of any other suitable method a per details (Initial load Test) 1200mm dia Pile

Carrying out load test on any pile as per standard procedure laid down in the IS:2911 specification including construction of test cap, dismantling the cap after test and cleaning the site and maintaining complete records of load settlement as directed by Engineer and as per specification, and submission of records. b. Load testing of foundation piles including loading with necessary kentledge of any other suitable method a per details (Routine load Test) 1200mm dia Pile

Performing Integrity Test (low strain) on vertical pile. The item shall include chipping of weak concrete at the top of pile, leveling, bending of reinforcing bars, preparation of pile head including testing with pile driving analyser or approved equivalent. To be carried out at least 15 days after concreting of piles. A specialist approved Agency shall be employed by the Contractor for the test. The test shall be carried out as per relevant ASTM code.The item is including complete testing with approved apparatus, analysis of results and conclusions including submission of test reports in three hard copies with soft copy in CD. 1200mm dia Pile

Providing and casting in situ controlled cement concrete M-35 for RCC bored pile from 1.2 m. dia. using Tremie Pipe including necessary flushing, dewatering, formwork, mixing in mechanised batch mix plant, transporting, compacting,and finishing including all leads & lifts complete as per detailed specifications. (Excluding Reinforcement)

Chipping and dressing of the RCC piles upto cut-off level (Min. 1 D) including cleaning of reinforcement and removal of dismantled materials, etc. for providing pile caps as directed by Engineer and as per specification. for 1200 mm dia. pile.

Providing and installing 6 mm MS liner for bored-cast-in-situ concrete piles including applying protective coating as per drawing and specification and as directed by Engineer.

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) bar reinforcement in foundation complete as per drawings and technical specifications 3) The work shall be done as per execution drawing.

Reinforced cement concrete in substructure complete as per drawings and technical specification R.C.C. grade M 25 ( Height 0 to 5 m)

Reinforced cement concrete in substructure complete as per drawings and technical specification R.C.C. grade M 25( Height 5 to 10m )

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) in substructrue complete as per drawings and technical specification

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications R.C.C M 25

Providing and laying TAR paper below solid slab

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications R.C.C M 40

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) in superstructure complete as per drawing and technical specifications

1.Providing and laying a buried expansion joint, covered with 12 mm thick, 200 mm wide galvanised weldable structrual steel plate as per IS:2062, placed symmetrical to centre line of the joint, resting freely over the top surface of the deck concrete, welding of 8 mm dia, 100 mm long galvanised nails spaced 300 mm c/c along the centre line of the plate, as per technical specifications Clauses 1207.2.3 2.Providing and fillling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight. 3.Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans, covered with sealant complete as per drawing and technical specificationswelding of 8 mm dia, 100 mm long galvanised nails spaced 300 mm c/c along the centre line of the plate, as per technical specifications

Reinforced Cement Concrete M 30 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3

P.C.C. M 15 ordinary grade (1:2:4) levelling course below approach slab complete as per drawing and technical specifications

Drainage spouts complete as per drawing and technical specifications

Providing and fixing marble slab including engraving letters / numbers, painting complete. (ii) Size 60cm x 60cm x 4cm

Painting on Concrete/Steel Surfaces with Epoxy Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification

Providing and fixing in position Mild steel dowel bars in pier caps or abutment caps for anchorage in fixed end as per detailed drawings including cutting, bending and welding complete.

Providing and fixing in position Mild steel dowel bars in pier caps or abutments caps for anchorage in free end as per detailed drawing including cutting, bending and welding complete.

Providing and laying Extruted Biaxial Polypropylene Geogrid 30 KN and thickness of layer 0.75m up to 3 m height and height between 3 to 6m Extruted Biaxial Polypropylene Geogrid 30 KN and thickness of layer 0.6m as directed by Engineer In charge and as per detailed specification

Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications

Reinforced cement concrete in substructure complete as per drawings and technical specification ans 1204(A) Height from 0.0 to 5.0 M.(3) RCC return (upto 10 ton) M20

Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of any, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto any and all lead as per Technical Specification

Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per Technical Specification

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification

Providing and applying primer coat with Bitumen emulsion (SS-1, IS:8887 Bulk) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 1.2-1.5 kg/sqm using mechanical means as per Technical Specification

Providing and applying tack coat with Bitumen emulsion (RS-1 Bulk) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification ( By Weight of 3.3% Mix VG 30)

Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification ( Type B 19 KG /10sqm VG 30)

Reinforced cement concrete M15 grade 200 m stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification

Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification

Providing and fixing of a typical design of PMGSY Informatory Sign Board “The board will be a composite unit consisting of three plates of Aluminum Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most plate will be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mm x 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart Centre to Centre. The top of the middle plate will be flushed with the top of 75 mm dia. medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond Shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. ii). the lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 Messages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing

Providing & fixing logo Board of Prandhan Mantri Gram Sadak Hojna as per standard design of National Rural road Development Agency diamond size ( 600 x 600 mm) 1.5 mm thick plate & board size (900 x 250 mm) 1.5 mm thick M.S. [late and 2.40 meter deep length single angle 75 x 75 x6 mm size incl. fitting & painting lettering with luminous colour as per drawing incl .fixing in C.C. 1:3:6 etc. comp.

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973.

Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per

Constrcution of Temporary Diversion with 7.50m wide formation width & 5.50m wide paved with necessay safety devise as per IRC SP:55 Having specified road Crust 200mm Thick GSB, 200mm Thick WMM, Primer Coat, Tack Coat & 20mm Thick MSS Surafce necessary pavement marking including both side continous on both edge marking /Center Marking with Thermoplastic paint and road stud at every 18m alternative on both edge with necessary poratble barricaeds with retro-reflective paint in alternative yellow and white stiprs, construction zone sign coveringadvance warning zone , approach trastion zone, work zone, and terminal transition zone, necessary regulatry, warning and infomation sign, required red laterns or warning light with all singnals having retro reflective sheet of high intensive garde and providing necessary 900mm dia 12 row double row NP-3 Pipe and maitaning the same through out construction period till completion of project and including final dismataling and disposal of the same.