Pradhan Mantri Gram Sadak Yojana Tender

Marking out the centre line of the bridge & various other component structure & complete lining out and levelling with the theodolites, levels including constructing necessary masonry reference pillars for lines and levels and establishing necessary bench marks etc. complete as directed including the cost of all materials & labour charges etc. complete.

Diversion of water course, providing Earthen bund with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a all lead as per Technical Specification

Providing flood gauge marks on substructure as per design including painting complete.

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Sandy Material

Earthwork in excavation for structures as per drawing and technical specificationsncluding setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a all lead, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Depth upto 0 to 3m. below GL

Excavation for foundation in sand, gravel, clay soft soils and murrum etc. including shoring, strutting dewatering as necessary and disposing of the excavated stuff as directed.(B) Depth from 3.0 to 6.0 M.and any lead for 10 Cum

Providing concrete for plain concrete in open foundations complete as per drawings and technical specifications II P.C.C grade M 15 ( 1: 2.5: 5)

Providing concrete for reinforced concrete in open foundations complete as per drawings and technical specifications II R.C.C grade M 25

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) bar reinforcement in foundation complete as per drawings and technical specifications

Providing concrete for reinforced concrete in open foundations complete as per drawings and technical specifications III P.C.C grade M 20

Reinforced cement concrete in substructure complete as per drawings and technical specification R.C.C. grade M 25

Reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 R.C.C. grade M 25

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) in substructrue complete as per drawings and technical specification

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications R.C.C M 25

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications R.C.C M 40

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) in superstructure complete as per drawing and technical specifications

1.Providing and laying a buried expansion joint, covered with 12 mm thick, 200 mm wide galvanised weldable structrual steel plate as per IS:2062, placed symmetrical to centre line of the joint, resting freely over the top surface of the deck concrete, welding of 8 mm dia, 100 mm long galvanised nails spaced 300 mm c/c along the centre line of the plate, as per technical specifications 2.Providing and fillling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight. 3.Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans, covered with sealant complete as per drawing and technical specificationswelding of 8 mm dia, 100 mm long galvanised nails spaced 300 mm c/c along the centre line of the plate, as per technical specifications

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 40 kg laid dry complete as per drawing and technical specifications

Reinforced Cement Concrete M 30 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications

P.C.C. M 15 ordinary grade (1:2:4) levelling course below approach slab complete as per drawing and technical specifications

Drainage spouts complete as per drawing and technical specifications

Providing Pylon consist of cast-in-situ concrete of M30 grade exposed finish as per drawing and as directed by engineer incharge. Rate includes providing required shuttering and form work but excluding stone slab & carving.

Providing and fixing marble slab including engraving letters / numbers, painting complete. (ii) Size 60cm x 60cm x 4cm

Painting on Concrete/Steel Surfaces with Epoxy Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification

Providing and laying Extruted Biaxial Polypropylene Geogrid 30 KN and thickness of layer 0.75m up to 3 m height and height between 3 to 6m Extruted Biaxial Polypropylene Geogrid 30 KN and thickness of layer 0.6m as directed by Engineer In charge and as per detailed specification

Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications

Reinforced cement concrete in substructure complete as per drawings and technical specification A) Height from 0.0 to 5.0 M.(3) RCC return (upto 10 ton) M20

Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a any distance, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and all lead as per Technical Specification

Providing, laying and spreading soil on a prepared sub-grade, pulverising, mixing the spread soil in place with rotavator with 4 per cent slaked lime with minimum content of 70 per cent of CaO, grading with motor grader and compacting with the road roller at OMC to achieve atleast 98 per cent of the max dry density to form a layer of sub-base as per Technical Specification

Construction of sub-base using lime-flyash admixture with granular soil, free from organic matter/deleterious material or clayey silts and low plasticity clays having PI between 5 and 20 and liquid limit less than 25 and commercial dry lime, slaked at site or pre-slaked with CaO content not less than 50 per cent, flyash to conform to gradation as per Clause 4.3 of IRC:SP:20, lime+flyash content ranging between 10 to 30 per cent, the minimum un-confined compressive strength and CBR value after 28-days curing and 4-days soaking to be 0.75 MPa and 25 per cent respectively, all as specified in IRC:88 including a lead upto 1000 m as per Technical Specification

Construction of granular sub-base by providing well graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site uptoany lead spreading in uniform layers with motor grader on prepared surface and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification . (A) Plant Mix Method (ii) For Grading I Material

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification

Providing and applying primer coat with bitumen emulsion (SS-1, IS:8887 Bulk) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification (I) Low porosity

Providing and applying tack coat with Bitumen emulsion (RS-1, IS:8887 Bulk) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site upto a all lead laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification 9 By weight mix of 3.3% VG 30)

Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification ( Type B 19kg/10 sqmt VG 30)

Construction of 100 mm thick HARD SIDE SHOULDER by providing quarry spall material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification .

Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification

Providing and fixing of a typical design of PMGSY Informatory Sign Board “The board will be a composite unit consisting of three plates of Aluminum Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most plate will be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mm x 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart Centre to Centre. The top of the middle plate will be flushed with the top of 75 mm dia. medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond Shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. ii). the lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 Messages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing.”

Providing & fixing logo Board of Prandhan Mantri Gram Sadak Hojna as per standard design of National Rural road Development Agency diamond size ( 600 x 600 mm) 1.5 mm thick plate & board size (900 x 250 mm) 1.5 mm thick M.S. [late and 2.40 meter deep length single angle 75 x 75 x6 mm size incl. fitting & painting lettering with luminous colour as per drawing incl .fixing in C.C. 1:3:6 etc. comp.

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973.

Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete

Constrcution of Temporary Diversion with 7.50m wide formation width & 5.50m wide paved with necessay safety devise as per IRC SP:55 Having specified road Crust 200mm Thick GSB, 200mm Thick WMM, Primer Coat, Tack Coat & 20mm Thick MSS Surafce necessary pavement marking including both side continous on both edge marking /Center Marking with Thermoplastic paint and road stud at every 18m alternative on both edge with necessary poratble barricaeds with retro-reflective paint in alternative yellow and white stiprs, construction zone sign coveringadvance warning zone , approach trastion zone, work zone, and terminal transition zone, necessary regulatry, warning and infomation sign, required red laterns or warning light with all singnals having retro reflective sheet of high intensive garde and providing necessary 900mm dia 12 row double row NP-3 Pipe and maitaning the same through out construction period till completion of project and including final dismataling and disposal of the same.