Pradhan Mantri Gram Sadak Yojana Tender

Providing flood gauge marks on substructure as per design including painting complete.

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Sandy Material

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.Depth upto 0 to 3m. below GL

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Hard rock (blasting prohibited)

Diversion of watercourse, providing Earthenbund with approved material obtained from borrow pits with a lift up to 1.5m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables300. 1and300.2 with a lead up to 1000m as per Technical Specification Clause 301.5

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203II P.C.C grade M 15

Filling annular space around footing in rock as per technical specification Clause 1203.4.3.P.C.C grade M 15

Providing and fixing HYSD/TMT dowel bars of minimum 32 mm dia for anchoring by drilling holes in foundation strata including necessary bending, hooking of dowel bars and grouting the holes complete as per detailed drawing and as directed.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203R.C.C grade M 25

Supplying, fitting and placingTMT bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204R.C.C. grade M 25 Height upto 5m

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204R.C.C. grade M 25 Height 5 to 10m

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5R.C.C M 30

Supplying, fitting and placing TMT bar reinforcement (Fe 500D) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

Providing and laying TAR paper below solid slab

Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans, covered with sealant complete as per drawing and technical specifications

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5R.C.C M 40

Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and fixing in position Mild steel dowel bars in pier caps or abutment caps for anchorage in fixed end as per detailed drawings including cutting, bending and welding complete.

Providing and fixing in position Mild steel dowel bars in pier caps or abutments caps for anchorage in free end as per detailed drawing including cutting, bending and welding complete.

P.C.C. M 15 ordinary grade (1:2:4) levelling course below approach slab complete as per drawing and technical specifications Clauses 800 and 1211

Reinforced Cement Concrete M 25 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications Clauses 800 and 1211

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3

Drainage spouts complete as per drawing and technical specifications Clause 1209

Providing and fixing marble slab including engraving letters / numbers, painting complete. Size 75cm x 60cm x 4cm.

Providing and laying Extruted Biaxial Polypropylene Geogrid 30 KN and thickness of layer 0.75 m up to 3 m height and height between 3 to 6 m Extruted Biaxial Polypropylene Geogrid 30KN and thickness of layer 0.6 m as directed by Engineer Incharge and as per detailed specification

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203R.C.C grade M 20

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204R.C.C. grade M 20 Height upto 5m

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204R.C.C. grade M 20 Height 5 to 10m

Providing and laying rubble pitching of 22.50 cm. thick with filling the sand in the interstices & C.C. 1:3:6 panelling at 3.0 mt. C/C and 30 cms. x 30 cms. panel wall as per the detailed drawing with necessary excavation and providing water chuts of C.C. 1:3:6 at 24.00 mt. C/C providing pointing on rubble pitching in CM 1 : 3 etc. complete.

Clearing and Grubbing Road Land (By Mechanical Means)Clearing and grubbing road land including up rooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.

Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 mas per Technical Specification Clause 301.4.

Granular Sub-baseConstruction of granular sub-base (GR-II) by providing well graded material, mixing in a mechanical mix plalce Method, carriage of mixed material to work site upto lead of 1000 m spreading in uniform layers with motor grader on prepared surface and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401

Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406.By Mechanical Means

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical SpecificationClause 402

Primer CoatProviding and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 1.05 kg/sqm using mechanical means as per Technical Specification Clause 502.

Tack CoatProviding and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.225 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Bituminous Macadam (50mm Thickness, VG-30 Grade and 3.3% BT Content by Weight of Mix)Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification Clause 504.

Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) aggregates using VG-30 Grade and Consumtion 22kg/10 Sqmt bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required leveland grades as per Technical Specification Clause 509.

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. The board will be a composite unit consisting of three plates of Aluminum Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most plate will be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mm x 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart Centre to Centre. The top of the middle plate will be flushed with the top of 75 mm dia. medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond Shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. ii). the lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 Messages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing.

Informatory Signs :-Providing and fixing sing boards made out of 2mm aluminium sheet; size 80 x 60cms. rectangle as per the design of IRC-67-1977 pre treated with phospheting process & acid teching; coated with one coat of epoxyprimer and two coats of best qualityepoxy paint; reflectorised with retro refiective sheeting as per latest M.O.S.T. Specifications; 3.1m long stand postand frame fabricated from suitable sizeiron angle of 35 x 35 x 3mm75x75x6mm as required; painted with best qualityepoxy coatings in black and whitebends. the details of symbol for eachboard shall details of symbol for eachboard shall be as per the instruction ofengineer in charge. The fixing at site shall be in 1:2:4 CC block of size 45 x45 x 60cms. for each leg. including excavation curing tec. complete under the supervision of engineer in charge.(A) Engineer Grade..............................

Cautionary Warning Sign :-Providing and fixing sing boards made out of 2mm aluminium sheet; size 90 x 90 x 90 cms. equilateral triangle as per design of IRC-67-1977. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint ;reflectorised with retro refiectivesheeting as per latest M.O.S.T.Specifications; 3.1m long stand postand frame fabricated from suitable sizeiron angle of 35 x 35 x 3mm, 75 x 75 x 6mm as required; painted with bestquality epoxy coatings in black andwhite bends. The details of symbol foreach board shall be as per theinstruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg.including excavation, curing etc.complete under the supervision of engineer in charge.(A) Engineer Grade...........................

Road Marking with hot thermoplastic paints with reflectorising glass beads on bitumin surface providing and laying a hot applied thermoplasic compound 2.5 mm thick including refectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is excluding of surface applied glass beds as per IRC:35-2015. The finished surface to be level, uniform and free from streaks and holes. Zebra patta/bump Patta lane/Centre line/ edge line/ Cut patta. The White color marking should provide liminance coefficient on cement road shall be min 130 mcd/m2/lux and Ashphalt road shall be min. 100 mcd/m2/lux during the service life during the day time. The marking should meet the performance criteria for night time reflectivity, wet reflectivity and skid resistance as mentioned in section-15 of IRC-2015 Warrenty For Reflectivity shall be Two Year.

Cat Eye / Road Stud/RPM: Supplying of MoIded Twin Shanks Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with MIcro prismatic lens (No Glass bead lens) capable of providing total internal reflection of the light entering the lens face and shall support a load of 13635 kgs. tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Ci,cular No RW/NH/33023/10-97- DO III Dt 11.06. 1997. The height, width and length shall not exceed 20 mm, 130 mm and 130 mm and with minimum reflective area of 13 Sqcm on each side and andd slope to the base shall be 35 +/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30 +/- 2 mm) from the body is ro be a ninimum value of 500 Kgf: Fixing will be by drilling holes on the road for the Shanks to go inside, Without nails and using epoxy resin based adhesive as per manufacrurer's recommendation and The color of the marker should be as per he IRC 35-201S and as directed by Engineer-In-charge.

Providing and fixing 'W' metal double beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail 70 cm above road/ground level fixed on ISMC channel vertical post 150mm x 75m x 5mm size erected at 1.5Mt. center to center,1.8 m high ,1.1 m below ground /road /level , all steel parts and fitments to be galvanised by hot dip process , all fittings to confirm to IS:1367 and IS 1364, metal beam rail to be fixed on the vertical post with a spacer of chsnnel section 150x75x5 mm,330mm long complete as per clause 810.

Constrcution of Temporary Diversion with 7.50m wide formation width & 5.50m wide paved with necessay safety devise as per IRC SP:55 Having specified road Crust 200mm Thick GSB, 200mm Thick WMM, Primer Coat, Tack Coat & 20mm Thick MSS Surafce necessary pavement marking including both side continous on both edge marking /Center Marking with Thermoplastic paint and road stud at every 18m alternative on both edge with necessary poratble barricaeds with retro-reflective paint in alternative yellow and white stiprs, construction zone sign coveringadvance warning zone , approach trastion zone, work zone, and terminal transition zone, necessary regulatry, warning and infomation sign, required red laterns or warning light with all singnals having retro reflective sheet of high intensive garde and providing necessary 900mm dia 12 row double row NP-3 Pipe and maitaning the same through out construction period till completion of project and including final dismataling and disposal of the same.

credit amount of 1140175/- (Rupees ) shall be recovered from the 1st running bill for payment