Institute For Plasma Research Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

Providing and constructing BRICK MASONRY in cement mortar as per mixes stipulated below using approved well burnt bricks of "CLASS DESIGNATION" (Classification as per I.S.1077-1986) as specified below, including raking out joints 10mm deep wherever required, curing, etc; complete at all lead and lifts all as per specifications (The mix ratio specified is for cement : coarse sand) USING BRICKS OF CLASS DESIGNATION "3.5"(Minimum Average Compressive strength not less than 3.5 N/sqmm) In foundation and plinth in cement mortar 1:6. Price includes fixing of chair bracket/rag bolt into masonary Complete all as directed by EIC.

Sand faced plaster- 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough using wooden gutka. Note- This item is for patch work including any lead and list for all heights

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. (channel, angle, plate, flat etc) as required In fence, post, gate and similar works

Providing and Applying two coats of Synthetic enamel paint / aluminum paint on MS member using 1st quality paint from approved manufacturer of approved colour and shade to give an even shade including scaffolding, removing of rust, cleaning the surface, preparing the surface to receive paint including filling cracks and creaves with Putty or other approved filler materials, applying two coats of paint to steel work. cost also includes thinner, filler, putty and other materials, necessary labours etc. complete as directed by Engineer in charge at all heights, in all floors. Painting on false ceiling includes taking down the material, surface preparation, Primer, paint and fixing the material back after painting. Note:- Actual painted area will be measured and paid. (1) Synthitic enamel Paint of approved brand (2) Putty suitable to Mild steel members of approved brand Note:- Measurements for GI fencing, factor 0.5 will be applicable on painted surface area.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm

Painting external plastered surfaces with two or more coats of Texture 100% ACRYLIC EXTERIOR EMULSION PAINT of approved make and colour having protection against fungal growth, flaking, fading, alkali and UV degradation and to give an even shade with required finish including applying a coat of Acrylic exterior primer as per manufacturer's application procedure, cleaning the surfaces, filling the crevices with approved filler, scaffolding, curing, etc., at all heights. complete all as per specifications. a) On sand faced / rough / smooth plastered surfaces. NOTE: Required Paint cofficient has to be considered in the quoted rate. Hence separate cofficient will not be considered while measuring the area for painting and area will be measured flat. The paint cofficient will be 1.00 irrespective of applying on plain / sand face plaster surface. No extra will be paid for rough or sand face plaster surface. Rate to included following materials.

Extra for additional lead for shifting of earth beyond 50 metre or part there of beyond 1st 50 metre up to 2 KM meter, including By mechanical loading, unloading and stacking