Indian Army Tender

Removing excavated material not exc 50 m and depositing where directed , Removing excavated material not exc 50 m and depositing where directed as a level n ot exc 1 point 5 m above the starting points

Material and labour for sand filling with clean dry find sand unwashed including gently punning around cables in trenches , Material and labour for sand filling with clean dry find sand unwashed including gently punning around cables in trenches oblique ducts for cable protection complete all as specified and directed by Engineer in Charge

Material and Labour PCC 1 2 4 type B1 using 20mm graded stone aggregate as in coping of poles , Material and Labour PCC 1 2 4 type B1 using 20mm graded stone aggregate as in coping of poles including necessary form work complete all as specified and directed

Material and Labour PCC 1 3 6 type C1 using 20 mm graded black trap oblique granite oblique basalt stone , Material and Labour PCC 1 3 6 type C1 using 20 mm graded black trap oblique granite oblique basalt stone aggregate for coping of the pole including necessary form work complete all as specified and directed

Material and Labour well burnt bricks sub class B as in protection of cable laid dry flat abutting , Material and Labour well burnt bricks sub class B as in protection of cable laid dry flat abutting each other width wise complete all as specified and directed

Providing platform for transformer of size 2point 5 into 2 point 5 into 1 point 5m high from GL including , Providing platform for transformer of size 2point 5 into 2 point 5 into 1 point 5m high from GL including excavation in trenches not less than 1 mtr PCC 1 5 10 type E2 for foundation brick work in cm 1 6 PCC 1 2 4 type B1 in copping plaster 10mm thick in cm 1 6 om brick complete surface PCC 1 4 8 type B1 sub base 75mm thick as in flour PCC 1 2 4 type B1 100mm thick floor using extra cement returning filling and removal on surplus soil including 2 Nos ISMB 100mm channel painting with 2 coat aluminium paint over a coat of red oxide primer and 3 coats of white washing on cement work for fixing transformer including ramp of suitable size mounting of transformer complete all as specified and as directed

Supply erecting and fixing in true vertical position steel tubular swaged pole 410 SP 55 11 mtr long complete with cast iron , Supply erecting and fixing in true vertical position steel tubular swaged pole 410 SP 55 11 mtr long complete with cast iron base plate pole cap finial taper welded reduced section and longitudinal weld throughout entire length of pole with and including 2 coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole finished with one coat of red oxide primer complete all as specified and directed by Engineer in Charge Note Earth work PCC in foundation and coping cross arms danger notice board and anti climbing device is measured and paid separately

Supply fixing commissioning and testing of outdoor gang operated switch GOD single throw single break off load , Supply fixing commissioning and testing of outdoor gang operated switch GOD single throw single break off load type of current rating upto 400 Amps nine pole each pole consisting of galvanized steel base HT insulators as per IS non ferrous knife and spring loaded contacts arcing horns of adequate section to break magnetizing current of the transformers horizontal GI pipe of adequate length for phase separation adequate length of GI pipes for operation from ground level and operating handle with locking arrangement complete in both OFF and ON positions All ferrous parts hot dipped galvanized and non ferrous heavily tinned to withstand weather and suitable for vertical mounting with fuse unit carrier of 200 Amps rating and fuse element upto 50 Amps along with rod for expulsion fuses and 3 Nos post insulators for fuses including dismantling and taking down existing unserviceable GOD switch complete all as specified and as directed by Engineer in Charge Make Jaipuria Brothers oblique HEI oblique ECE Calcutta

Disconnecting Taking Out and shifting of the any make of transformer rating 100 KVA mounted on plinth , Disconnecting Taking Out and shifting of the any make of transformer rating 100 KVA mounted on plinth oblique pole from existing location to new location and existing transformer vice versa including removing and reconnections of HT LT side jumper cable connection control cable connection of both transformers including testing and commission complete all as directed by Engr in Charge Note one The rate quoted is deemed to be inclusive of necessary crane vehicle charges for shifting and installation of the transformer

Supply lay connect test and commissioning of 3 core 95 Sqmm 11000 Volts grade Earthed XLPE , Supply lay connect test and commissioning of 3 core 95 Sqmm 11000 Volts grade Earthed XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables heavy duty with aluminum conductor laid in trench under ground wall surafce tunnel duct complete all as directed by Engineer in Charge

Material and Labour for Cable jointing kit for 11 KV Earthed grade cable for indoor termination , Material and Labour for Cable jointing kit for 11 KV Earthed grade cable for indoor termination Heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of 3 core XLPE armoured aluminium conductor cable of size 95 sqmm

Supply laying and testing cable XLPE Insulated Earthed screened PVC bedded galvanized , Supply laying and testing cable XLPE Insulated Earthed screened PVC bedded galvanized steel strip or wire armoured electric power cables heavy duty 1100 Volts grade with stranded aluminium conductor of size 185 sq mm 3 point 5 core

Supply install commissioning and testing factory made Design verified as per IS IEC61439 1 , Supply install commissioning and testing factory made Design verified as per IS IEC61439 1 and 2 by CPRI approved manufactures along with FAT floor mounted powder coated comprising LT panel box KIOSK out door typesize platform mounted suitable for 415 volt 3 phases 4 wire 50 Hz AC supply system all as specified and directed having busbar chamber with 4 Nos insulated AL bus bars 600 amps rating installed on percelain insulators the panel shall be dust and vermin proof double door made of 3 point 15 mm CRCA MS sheet outer and inner and individual compartment for MCCB oblique volt oblique Amps meter and 50 into 50 into 6 mm thick angle iron for base frame work having angle iron 4 Nos each Suitable long welded to frame oblique cubical and grouted in ground upto 0 point 5 Meter by using PCC 1 2 4 B2 of Suitable size the ground over the ground level upto 1 Mtr height 2 Nos earth terminal to be welded with feeder piller the complete feeder pillar box should be anti corrosive coating and finally epoxy polyester powder coating of flint grey shade RAL 7032 including internal wiring with PVC insulated solid copper conductor FRLS cables appropriate size but not less than 2 point 5 Sqmm Front with suitable lugs for incoming oblique outgoing feeders and comprising of all as specified as under Incomer First MCCB FP 250 A 36 kA with fixed one no Second 4 Nos aluminium bus bars of 400 Amp current rating capacity of suitable size of length as actually required at site for 3 phase and neutral mounted on epoxy oblique FRP bus bar insulator complete with nut bolt fixing arrangement complete one set Outgoing MCCB FP 100A 16KA with fixed thermal release 3 Nos Material compartment first Digital type Amp meter 0 to 250 Amp size 96mm into 96mm with selector switch and 3 Nos CT of ratio 250A oblique 5A 01 No second Digital type volt meter 0 to 500 v with selector switch one Nos Third RVB LED incating lamp 3 Nos

Supply and fixing cross arms bracing supports clamps and back plates fabricated from , Supply and fixing cross arms bracing supports clamps and back plates fabricated from structural steel sections including nuts and bolts washers welding bending cold or hot drilling holes for bolts in any shape or size as indicated or directed and inclusive of two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed by Engineer in Charge

Pin type porcela in vitreous white brown or green insulator including , Pin type porcela in vitreous white brown or green insulator including one galvanised mild steel spindle two galvanised iron washers and one galvanised iron nut 50mm height 150mm height 150mm dia for 11000 volts grade

Single disc assembly for tension with tension clamps , Single disc assembly for tension with tension clamps for conductors working pressure 11000 volts

Aluminium conductor steel reinforced , Aluminium conductor steel reinforced

Material and Labour for earthing complete with galvanized steel earth plate , Material and Labour for earthing complete with galvanized steel earth plate 600 into 600 into 6 mm thick buried directly in ground earth pit not less than 2 point 25 Mtr deep below normal ground level with top edge of plate not less than 1 point 5 Mtr below normal ground level connected to galvanized iron earth strip 32 into 6 mm as earthing lead by means of bolt nuts check nuts and washer of galvanized iron or steel besides welding of all joints as shown in drawing and including excavation and earthwork G I pipe light grade 40mm bore for protection of G I strip from earth electrode to incl the earth test point supplying and laying charcoal dust common salt PCC 1 2 4 type CI chamber and MS angle iron frame 40 into 40 into 3mm RCC cover 40 mm thick 1 2 4 type BI using 20 mm graded stone aggregate reinforced with 6 mm dia round bars 75 mm c c both ways with MS handle 12 mm dia CI funnel and wire mesh 20 mm dia GI pipe light graded for watering all as shown in drawing and connected to earth test point incl testing complete all as specified and directed