Food Corporation Of India Tender

Supply of Surface waterproof industrial luminaire with polycarbonate housing and diffuser suitable for twin 4ft T8 tube along with 2 Nos of 20 or 22 Watt LED polycarbonate T8 tube with in build driver with metal heat sink with ingress protection of IP66. (NABL certified as per ISO/IEC specification)

Dismentling,Refixing,Installation, testing and commissioning of all types existing lighting fixtures, complete with all accessories etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of all types lighting fixtures, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Dismantling of all types lighting fixtures, complete with all accessories and tube etc. on ceiling/ wall as required.

Supply & fixing of 150 watt LED Flood light luminaries of Area lighting with energy saving Main Housing,Powder coated pressure dia cast aluminium housing, , Front Clear toughened glass, Suitable secondary lens for better light distribution Gear : Electronic constant current driver of min. Operating Voltage : 140 V - 270 V, Rated Voltage & Frequency : 240 V, 50 Hz, AC with IP 66 protection and SPD as reqd.

Supplying of XLPE insulated & PVC sheathed aluminium conductor armoured cable of 1.1 KV grade of size 2 X 10 sqmm, confirming to IS:7098 (Part- I) 1988 with up to date ammendment and necessary size aluminum lugs and accessories for connection as required

Supplying and making end termination with brass compression gland and aluminium lugs for 2 X 10 sq. mm (19 mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Dismantling, repairing, painting and refixing of existing loop box including S & F of following items on it: HD Connector for 10 to 16 sqmm 4 ways - 1 No. 6 amp SP ,C, curve 10KA MCB - 1 No. fixing Clamps - 2 Nos.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, Installation, testing & commissioning of cubicle type totally enclosed free standing type moisture, dust and vermin proof Panel Board made out of 2.0 mm thick CRCA sheet Steel IP 42 Wall / floor mounting type with minimum dimension of 1500 mm(H) X 1450 mm (W) X 350 mm(D)fabricated in compartmentalized design. The sheet steel shall undergo minimum 9 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 V electrolytic, 400 Amp Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect. All MCCB shall have thermalmagnetic release with adjustable over current,short circuit & Earth fault protection with trip history (Faulty phase, type of fault and interupted Current) . All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking arrangement, with adjustable O/L & S/C trip setting as per load requirement. All TP MCCB shall be with solid isolable neutral link. The breaking capacity specified is Ics value. All outgoing MCB's shall be C type with 10 KA breaking capacity. The fault withstanding capacity of panel shall be 25 KA rms for 1 sec. The above board shall be complete with 3 nos. phase indicating lights, flush AVF meter with, CT's, PT's, selector switches, protective fuses etc. at Incomer with all inter connections by min. 2.5 sq.mm. Copper wires alongwith switchgears as mentioned below: Incoming- 1 No of 250 Amp FP Moulded Case Circuit Breaker. (36 KA) (Conforms to IS/IEC:60947-2), Outgoing- 3 Nos of 125 Amp FP Moulded Case Circuit Breaker. (25 KA)(Conforms to IS/IEC 60947-2), 2 Nos of 63 Amp FP Moulded Case Circuit Breaker. (25 KA), 2 Nos of 32 Amp DP Miniature Circuit Breaker. (10 KA)

Supplying, Installation, Testing & Commissioning of out door wall mounted type section pillar of minimum size 1200mm X 600mm x 400mm suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade and shall be dust proof, verm proof, water proof, removable cobers, gasketed and seperate removable gland plate, having 250 Amp capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., & common GI earth bar of size 32 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bars and control wiring with adequate size PVC insulated copper conductor S/C cable ,mounting on MS angle base frame of required size and the same will be installed in ground with necessary CC foundation alongwith switchgears as mentioned below: Incoming- 1 No of 100 Amp FP Moulded Case Circuit Breaker. (26 KA) (Conforms to IS/IEC:60947-2), Outgoing- 4 Nos of 63 Amp FP Moulded Case Circuit Breaker. (10 KA) (Conforms to IS/IEC:60947-2), 2 Nos of 32 Amp DP Miniature Circuit Breaker. (10 KA)

Supplying and making end termination with brass compression gland and aluminium lugs for 4 X 16 sq. mm (28mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3.5 X 35 sq. mm (32mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3.5 X 70 sq. mm (38mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying of XLPE insulated & PVC sheathed aluminium conductor armoured cable of 1.1 KV grade of size 4 x 10 sqmm, confirming to IS:7098 (Part- I) 1988 with up to date ammendment and necessary size aluminum lugs and accessories for connection as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of Upto 35 sq. mm size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size up to 35 sqmm on wall surface as required

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of Upto 35 sq. mm size in the existing RCC/ HUME/ METAL pipe as required.

Providing, laying and fixing 80 mm dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required

Supplying, installation , testing and commissioning of motor starter Panel, suitable up to 5 HP/3.73 KW, 3 phase 50 Hz, A.C. monoblock pumpset including following metres, items mounted on it with FRLS (Fire retardant low smoke) Internal wiring connection provided with Protection Degree IP 54. (Conforms to IS/IEC 60947-4-1) (i) 0 to 60 Amperes Ammeter-1 No. (ii) 0 to 500 volts. voltmeter-1 No. (iii) DOL starter LT/LK make with contactor & Relay. iv) Selector switches for metres. (v) ON-OFF switch. (vi) HRC fuse with links & neutral link set / MCB. (vii) Single phasing preventor- 1Nos. (viii) Water level guard/controller with wiring (ix) R-Y-B indicators with lamps/LED. (x) On-OFF Push buttons.

Providing and fixing 50 mm nominal dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Supply and laying of 3 core x 2.5 sqmm size PVC insulated and PVC sheathed multy strand copper conductor 1100 V grade submersible flat cable with provision of water tight joint as req.

Lowering the monoblock submersible water pump along with pipe line and submersible flat cable into the open well / underground tank including G.I./PVC Pipe Line, Valves etc as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required

The following items are to be dismantled during the work and take away by the giving the credit to the work estimate on as is where is basis

Like wire pices, cable pices, lighting fixtures , loop boxes, ceiling fans, feeder pillar, cubical panel, all electricals materials, disconnector fuse, etc.