Public Works Department Tender

Providing and applying tack coat with bitumen grade of 80/100 or bitumen emulsion using pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom as per MoRT&H specifications clause 503. Bitumen 80/100@ 0.375 kg/sq.m

Providing and laying bituminious concrete with 40-60 TPH Drum Mix type Hhot mix plant producing an average output of 50 tonnes per hour using crushed aggregates of specified grading, premixed with bituminious binder to mix with filler, transporting the hotmix to work site, with all leads laying with a hydrostatic/hydraulic paver finisher with sensor control to the required grade, level and alignment, using antistripping agent rolling with smooth wheeled, vibratory or tandem rollers to achieve the desired compaction complete as per MoRT&H Specifications Clause 509 Grade-II (13mm nominal size) @ 6.0% Bitumen of grade 60/70 a )Antistripping agent @ 0.5% of bitumen content

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC : 35. The finished surface to be level uniform and free from streaks and holes as per MORTH Specification 803

Providing & laying of minimun 80mm thick factory made Shot blasted cement concrete Interlocking paver blocks of minimum M40 and above grade made by heavy duty block making machine with strong vibratory compaction and of approved size and design/ shape laid in 50mm thick compacted bed of coarse sand, filling the joints with coarse sand etc. all completed as per the direction of Engineer-incharge. The product should comply with IS 15658: 2006 and manufactured by ISO 9001: 2008 certified plant. 1)Size: 210mm x 150mm x 80mm thick (Type: Rectangular Type Pavers) b)Other Colours To be procured through GHRSSIDC and the payment shall be released on submission of invoice.

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. d) Size 60 cm L x30 cm H x 10cm T To be procured through GHRSSIDC and the payment shall be released on submission of invoice.

Road Markers/Road Stud with Lense Reflector (Providing and fixing of road stud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) To be procured through GHRSSIDC and the payment shall be released on submission of invoice.

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Place Identification Sign/Informatory Sign/Adv.Dir Sign/Reassurance Sign with SS Structure a) Providing & fixing of Direction & Place Identification sign board (Less than 0.9 sq.mtr) made out of retro reflective sheeting conforming to Type XI standards of ASTM D4956-09 & as per IRC-67: 2012 specifications, fully covered over 4mm thick ACP/2mm thick Al supported with back support frame of 35x35x5 mm stainless steel angle, 304 Gradewith areas not exceeding 0.9 sq.mtr and surrounded by 35mm dia stainless steel pipe of 304 Grade. Board Shall be fixed to a vertical posts of 80mm dia stainless steel pipe, 304 grade of 3.6 mtr height and firmly fixed to the ground by means of properly designed foundation with M20 grade cement concrete 45 cm X 45 cm X 60 cm etc, 60 cm below ground level. 10 years warranty & a certified copy of three years outdoor exposure report from an independent lab as per IRC 67-2012 for Type XI retro reflective sheeting shall be submitted by the contractor. To be procured through GHRSSIDC and the payment shall be released on submission of invoice.

Cautionary/Mandatory/Facility Information Sign Board with SS Structure Providing & fixing of cautionary sign board of Cautionary/Mandatory/Facility Information sign board made out of retro reflective sheeting conforming to Type XI standards of ASTM D4956-09 & as per IRC-67: 2012 specifications, fully covered over 4mm thick ACP/2mm thick Al supported with back support frame of 25x25x3 mm stainless steel angle of 304 grade. Board Shall be fixed to a vertical post of 80mm dia stainless steel pipe of 3.6 mtr height and firmly fixed to the ground by means of properly designed foundation with M20 grade cement concrete 45 cm X 45 cm X 60 cm etc, 60 cm below ground level. 10 years warranty & a certified copy of three years outdoor exposure report from an independent lab as per IRC 67-2012 for Type XI retro reflective sheeting shall be submitted by the contractor. b)600 mm Triangle - Cautionary Sign To be procured through GHRSSIDC and the payment shall be released on submission of invoice.

Add 1% cess on item No.9, 10,11 & 12