Goa Tourism Development Corporation Limited Tender

Supply, installation, testing and commissioning of 45W LED streetlight fixture with pressure die cast housing with individual LEDs with modular secondary optics and IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device. Make Bajaj, Havells,VinLed, Crompton, Transrail, Panasonic,Wipro,atilite,ecolink,transrail. or Keslec as directed by the engineer incharge.

Supply and installation testing and commissioning of 10KV Surge Protective Device. Make Suncity, Wipro,hypro,transrail,atilite,invertronics,ecolink or equivalent as directed by the engineer incharge.

Supply and installation testing and commissioning of 80W Street Light Driver. Make Suncity, wipro or equivalent as directed by the engineer incharge.

Supply, installation, testing and commisioning of SGDO -20/6, winch for 20Mtrs High mast with manual handle, roller chain, winch sprocket make : bajaj, Bharat or Volmont, haveloid, jaideep entrrprise,rishab conforming to IS standard, complete as required as directed by Engineer Incharge.

Supply, installation, testing and commisioning of DDMFO -30/8PB, winch for 20Mtrs High mast with manual handle, roller chain, winch sprocket make : bajaj, Bharat or Volmont, haveloid,jaideep enterprise, rishab engineering conforming to IS standard, complete as required as directed by Engineer Incharge.

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 core 16 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 core 2.5 sq.mm

Supply of 4 core armoured PVC insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part II) with latest amendments of following size. 4 core 25sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground in the same trench in one tier horizontal formaion including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.(a) In soily strata

Supply, Installation,Testing and commissioning of Outdoor double door IP54 Control Panel and supply of the following : Incoming (i)60A, TP MCCB,10KA (make L & T or equivalent)-01 No. (ii)63A, TP,MCCB,10KA with handle (make L &T or equivalent)-01 No (iii)6A,SP , MCB (make Hager)- 4 Nos. (iv)RYB LED indicating Lamp(make Esbee)-3 Nos.(v)6A,Toggle Switch-3 Nos. (vi)70A,TP Contactor (make L&T)-2Nos (vii)24hrs single Dial Switch-2 Nos.(viii) Digital timer (ix) 40A contactor. (x) Digital timer Outgoing (i)6 - 30 Amps,SP,MCB for outgoing (make Hager)- 6 Nos. (ii)10 sq.mm terminals (make Elmex)- 6Nos. (iii)Neutral Link, 30A, 6 way-01 No.(iv) 2kVa stabiliaers-3nos. including fixing of existing meter in the Panel box, Make: BCH, Electro controls or equivalent, as directed by engineer in-charge complete as required.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement. (a) In soily strata

Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop arthing . as required

Supply and Laying of PVC wire 2C X 4Sq.mm 1.1KV grade for service connection.

Supplying and fixing 0.5 A to 5 A rating, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required". (a) SP, Cat A

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (d) TP Cat A

Supplying and erecting Programmable Digital Almanac Timer Micro-controller based with real time clock to operate on derived switching “ON” & switching “OFF” street light as per daily sunset and sunrise respectively automatically having 4 digit LED continuous time display, relay output 230/250V / 10A with 10 Hrs battery backup and manual over drive facility capable to drive different capacity contactors timer erected in MS box in an approved manner.(1No)

Supply and fixing of 40A Contactor

Dismantling and shifting dismantled high mast to brittona residency complete as required as directed by Engineer Incharge.

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. (a) all kinds of soil

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Providing and laying in position ready mixedconcrete (RMC) High Performance Concrete per MORTH clause 1715 manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strengthanddurability as per the directions of the engineer- in-charge. All works upto floor V level. M-30 grade of concrete

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Supply of 12.5M high mast shaft in two sections suitable for wind speed 44m/sec. with head frame, luminaries carriage suitable to install 6-8 nos. of luminaries in symmetrical arrangement, lightning finial along with Supply of Accessories required such as double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box etc.

Supply of foundation bolts 6xM24x850mm manufactured from special steel along with nuts, washers, anchor plates and templates as directed by the engineer incharge.

Supply of LED Single dome aviation obstruction light as directed by the engineer incharge.

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade complete as required. (a) 4 core 25 sq.mm

Supply and installation testing and commissioning of 72W Hanging street Light Fixure . Make Suncity or equivalent as directed by the engineer incharge.

Supply and installation testing and commissioning of 1metre span single arm Dingo bracket . Make Suncity or equivalent as directed by the engineer incharge.

Supply and installation testing and commissioning of 1metre span double arm Dingo bracket . Make Suncity or equivalent as directed by the engineer incharge.

Supply of all in one integrated LED solar streetlight consists of solar photovoltaic module, battery, battery management system, control electronics, LED driver, PIR sensor, inter connecting cables and pole mounting piece integrated into the luminaire as a single unit. Solar street light with IP65 ingress protection having a system wattage of 17W with 3000 lumen output, 35Wp high efficiency monocrystalline solar panel, highly efficient MPPT based charge controller and 12.8 V, 20 Ah IP68 Lithium Ferro Phosphate(LiFePO4) battery with proper battery management system. LED lumen efficacy shall be at least 175lm/W and LED driver should have 90% efficiency. Typical correlated colour temperature should be 5700K with CRI70. It should have a PIR sensor to ensure battery optimisation with help of a suitable dimming profile. The luminaire should be housed in IK 08 impact resistance certified aluminum pressure diecast housing with anti-corrosive coating and must have a UV stabilized polycarbonate cover. The luminaire shall have a specially designed pole mounting piece that enables lateral as well as post top mounting and installation at varying tilts from 0 to 15 degrees for optimal light distribution. The LED driver should comply to IEC55015 -3 - 2 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI,Company LOGO shallbe Engraved.

Supply, Installation &Testing of LED retrofitting of HPSV 150W fixtures with 90W-94W output having bridgelux white colour SMD led & phillips xitanium driver.

Supply, Installation &Testing of LED retrofitting of HPSV 75W fixtures with 35W-40W output having bridgelux white colour SMD led & phillips/osram/fulham driver.

Liasoning with Electricity Department, electrical inspector, preparing necessary documentation work like test certificates, test reports, layout diagram etc and payment of necessary supervision charges, service connection charges to Electricity department, taking readings of resistance values, eath loop values by using meggar, earth loop resistance meter, voltmeter and clampmeter and submitting data to GED for handing over of light poles as required as directed by the engineer incharge.

Supply, installation of street Light fixture Coupler replacement with Paint as directed by the engineer incharge.

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only. (b) 10 to 40 A

Supply, DESIGN ,MANUFACTURING AND testing, COMMISSIOING OF OUT DOOR TYPE FEEDER PILLAR PANEL, fabricated out of 14 SWG CRCA SHEET of approved colour and having IP54 class of protection with double door the panel board shall compartmentalized free standing ,panel mounted to allow smooth entry and exit of cables ,it should be dust and vermin proof with gasket hinged cover doors the panel board shall be rested on angle frame of size 65mmx8mm minimum and properly grouted on the floor the angle frame support shall dedusted with acid treatment and duly with two coats of red oxide primer and duly powder coated with oven process as required the panel board shall extruded frame both sides and tinned aluminum either side the panel 150mmfor connections to earthing system and having following accessories AS DIRECTED BY ENGINEER INCHARGE COMPLETE AS REQUIRED IN COMING MCCB-4POLE 415 Volts, 125 AMPS RATING; (25KA) with rotary handle operating mechanism and adjustable thermal magnetic release for over load and short circuit protection L&T /SIEMENS OR EQUIVALENT.1 SET OF R YB PHASE indicating lamps LED type with each lamp individually protected by 2A SPMCB.1 NO Voltmeter range 0-500 volt,size (96x96)mm square with three position sector switch L&T 1 NO ammeter range (0-400amps size (96x(96)mm square with three positions slector switch L&T. 3 nos 400/5amps class 1/ 15 vacts for CTS for ammeter. BUS -BAR chamber ;250amps 50 hz with short circuit withstand capability of 50 ka/1sec shall be of ec grade aluminum tinned covered with colour coded heat insulating sleeves, compartment for installing 4KVA voltage stabilizer. and suitable for extension on either side of panel.OUT GOING FEEDERS 2NOS 63AMPS-4-POLE MCCB (10KA), 6NOS 25AMPS-TPN MCB (10KA).The panel shall be provided with bottom glands places for cables enty s, suitable reinforced and 3mm thick minimum for incomer sections, to reset warping, bending sagging of gland plates under the cabling loads. BUS BAR extension /terminals for cables termination at the incomer and outgoing ends of respective feeders shall be suitable for termination of cables THE PANEL dimensions and size shall be designed to allow spread out and proper dressing in a workmanship like manner of incoming and outgoing cables within the panel enclosure suitable supports shall be provided for clamping cores of cables after proper forming and dressing.3 pole Contactor 40A and Timer Circuit for ON/Off operation ALL THE MCCBS ,MCBS SHALL BE MADE OF L&T /SIEMENS /ENGLISH ELECTRIC OR EQUILENT