ZAMBOANGA SIBUGAY POLYTECHNIC INSTITUTE Tender

Description Invitation For Submission Of Quotation (small Value Procurement) Tools Plier 10in (cutting, Combination, Long Nose, Mechanical) 4 Set Dial Gauge With Magnetic Stand 2 Pc Vernier Caliper 4 Pc Torque Wrench (30 Kgf- Cm) 2 Pc Torque Wrench (230 Kgf- Cm) 2 Pc Torque Wrench (460 Kgf- Cm) 2 Pc Torque Wrench (920 Kgf- Cm) 2 Pc Torque Wrench (1900 Kgf- Cm) 2 Pc Torque Wrench (2800 Kgf- Cm) 2 Pc Puller (to Remove Flange Coupling Lock Nut) 2 Pc Puller (to Remove Flange Coupling) 2 Pc Puller (to Remove Spider Bearing) 2 Pc Puller (for Removing The Drive Shaft) 1 Pc Puller (for Removing The Axle Shaft) 1 Pc Puller (for Removing Transmission Gears) 2 Pc Drive Shaft Nut Chisel (for Un Staking The Front Axle Shaft Nut) 2 Pc V Block 4 Pc Union Nut Wrench (10 Mm)* 4 Pc Snap Ring Expander 4 Pc Hexagon Socket Wrench (6 Mm)* 4 Pc Hexagon Socket Wrench (8 Mm)* 4 Pc Pin Punch (5mm)* 4 Pc Plastic Hammer 4 Pc Ball Peen Hammer, 1lb 5 Pc Micrometer (0 – 25mm) 4 Pc Caliper Gauge 4 Pc Inside Diameter Measuring Tools 4 Pc Drill Bit Set, For Metal 1 Set Screw Extractor Set 1 Set Steering Wheel Puller 2 Pc Torx Driver (6mm) 2 Pc Torx Driver (8mm) 2 Pc Hexagon Wrench (24mm) 4 Pc Cylinder Stopper Wrench 4 Pc Pinion Shaft Wrench 4 Pc Stainless Steel Ruler, 12” 4 Pc Union Nut Wrench (10mm) 4 Pc Coil Spring Compressor, 1 Ton, Hydraulic 4 Pc Ball Joint Remover And Installer 4 Pc Clutch Aligner 1 Set Grease Gun 1 Pc Tire Deep Gauge 1 Pc Feeler Gauge 5 Pc C-clamp 2 Pc Pilot Bearing Puller 1 Pc Brake Bleeder 4 Pc Tire Pressure Gauge, Ball Pen Type 1 Pc Sst (prevent Oil Leakage From Transmission)* 2 Pc Sst (puller For Removing Transmission Gears)* 2 Pc Sst (to Remove Flange Coupling Lock Nut)* 2 Pc Sst (to Remove Flange Coupling)* 2 Pc Special Tools (such As Sliding Hammer)* 2 Pc Equipments Crocodile Jack, 3 Tons 2 Unit Safety Stand, Heavy Duty 8 Unit Transmission Jack , 1 Ton 1 Unit Electrical Reel 1 Unit Electric Drill 1 Unit Air Dust Gun 5 Unit Bench Vise 6 Inches 4 Unit Hydraulic Press, 1 Ton 1 Unit Bench Grinder, 1hp 1 Unit Camber-caster-kingpin Gauge 1 Unit Wheel Balancer 1 Unit Creeper 1 Pc Drain Pan, 20l Cap. 1 Pc Materials Caliper Brake Overhauling (o/h) Kit 4 Set Drum Brake Overhauling (o/h) Kit 4 Set Brake Wheel Cylinder Repair Kit 2 Set Tray, Aluminum, 20cmx20cm 4 Pc Mechanic Blue, 200ml 1 Tube Gloves 25 Pair Hard Hat 25 Pc Safety Shoes 25 Pair Cover All 25 Pc Face Mask 25 Pc Goggles 25 Pc The Zamboanga Sibugay Polytechnic Institute (zspi) Formerly Kabasalan Institute Of Technology (kit), Through The General Appropriations Act (gaa) Of 2018 Intends To Apply The Sum Five Hundred Seventy-five Thousand Two Hundred Ten Pesos Only (php 575,210.00) Being The Approved Budget For The Contract (abc) To Payments Under The Contract For Procurement Of Chassis Repair Nc Ii Utpras Registration Use. Price Quotation Received In Excess Of The Abc Shall Be Automatically Rejected At Bid Opening. Procurement Will Be Conducted In Consonance With Section 53.9 Negotiated Procurement (small Value Procurement) Of The 2016 Revised Implementing Rule And Regulations (irr) Of Republic Act 9184 (r.a. 9184), Otherwise Known As The “government Procurement Reform Act”. Only Sealed Bids/quotations From Eligible Bidders Will Be Opened And A Contract Will Only Be Awarded To The Lowest Calculated Responsive Quotation. Price Quotation Must Be Delivered To The Address Below On Or Before November 11, 2024; 12:00 Noon. Opening Of Price Quotation Shall Be On November 11, 2024; 2:00 P.m. At Zspi Fbs Room. Late Price Quotation Shall Not Be Accepted. The Zamboanga Sibugay Polytechnic Institute (zspi) Reserves The Right To Accept Or Reject Any Bid, To Annul The Bidding Process, And To Reject All Bids At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Bidder Or Bidders. For Further Information, Please Refer To: Analyn J. Ellorin Chairperson Bids And Awards Committee Other Information Items Listed In Request For Price Quotation Form Shall Be Awarded On Approved Budget For The Contract Basis.