Oriental Mindoro Tender

Description Rfq No.2024- _____ Date: ____________ Request For Quotation Supply And Delivery Of Material Testing Equipment To Be Used In The Engineering Office The Municipal Government Of Pinamalayan Hereinafter Referred To As “the Purchaser”, Through Its Bids And Awards Committee (bac), Invite Interested Parties To Submit Price Quotation For The Supply And Delivery Of Material Testing Equipment To Be Used In The Engineering Office Through Negotiated Procurement-two-failed Biddings (sec. 53.1, Irr Of R.a 9184) With Approved Budget For The Contract (abc) Of Four Hundred Fifty Three Thousand Six Hundred Pesos Only (p 453 ,600.00). Item/lot No. Quantity Units Item Description Abc Lot 1 Lot 2 Lot 3 1 3 3 3 3 1 1 1 1 1 Unit Sets Sets Sets Sets Set Set Unit Set Unit California Bearing Ratio Machine California Bearing Ratio Tester Maximum Load : 50 Kn Load Speed: 1.0/min Penetration Bar: 50.8mm X 100mm Platen Travel: 50mm Platen Dia: 170mm Mould Dia: 152mm X 170mm Dimension Size: 34 X 45 X 88 X Cm Power: 220 X 50hz 150w Weight: 82kg Concrete Slump Cone Equipment 10 X 30 X 30 Cm Concrete Beam Steel Mold 6” X 6” X 21” Steel Concrete Cylinder Steel Mold 4”x 8” Steel Concrete Cylinder Steel Mold 16”x 12” Sand Cone Apparatus Bottom Cone: 6 ½ Diameter Width: 1 Gallon Threaded Jar Width : Retachable Value With A ½ Diameter Orifice Field Density Test Apparatus 1 Pc Ladle For Scooping Soil 12 Pcs Aluminum Cans For Soil Samples 1 Gallon Container Can 1 Pc Rubber Mallet 1 Pc Sand Scoop 1pc Soft Brush 1 Pc Concrete Chisel Soil Compactor With 500x588mm Base Plate Gasoline Engine Engine Power: 6-5 Hp Weight: 127 Kg Frequency: 4300 Vpm (vibration Per Minute) Cetrifugal Force: 25kn Compactor Depth: 30cm Travel Speed:25cm/s Efficiency:500m3/hr Plate Size:50cm/58.8cm Sieve Analysis Machine With Test Sieves Sieve Brass: 3”, 2 ½ “, 2”, 1 ½’’, 1”, ¾”, ½”, ¼”, 3/8 #2, #8, #10,#12,#16, #20, #30, #80, #80, #100, #200 W/ Pan And Cover 8x2”, Wash Nsieve, #200. Fine Sieve Cleaning Brush Laboratory Drying Machine Liner Material: Stainless Steel Internal Space :35 X 35 X35 Cm External Size: 48 X 46 X 57cm Power Voltage: 800w/220v Volume:43l 453,600.00 All Items Listed Under The Purchaser’s Specifications Must Be Complied On A Pass-fail Basis. Failure To Meet Any One Of The Requirements Will Result To Rejection. Likewise, It Is Understood That Purchaser’s Specifications Are Minimum Requirements. The Bidder/supplier May Offer Higher Specifications Or Additional Items, If Any. Procurement Procedures Will Be Conducted In Accordance With The Provisions Of The Implementing Rules And Regulations (irr) Of Republic Act No. 9184 (government Procurement Reform Act). It Is The Intent Of The Purchaser To Evaluate The Quotation For Each Item/lot And Compare It With Other Bids/quotation Separately And Recommend For Contract Award Separately. Contract Award Will Be Made To The Lowest Evaluated Quotation, Per Item/lot, Meeting Purchaser’s Technical Specifications. Likewise, In Accordance With Section 53.9 And Appendix A Of Annex “h” (consolidated Guidelines For The Alternative Methods Of Procurement) Of The Irr Of Ra No. 9184, The Supplier Shall Provide The Following Documentary Requirements As A Condition For Award Of The Contract: 1. Mayor’s Permit 2. Philgeps Reg. No. 3. Omnibus Sworn Statement Your Prices Must Be Quoted In Philippine Peso And Must Include The Unit Price And Total Price, Inclusive Of All Taxes To Be Paid And Other Incidental Cost To The Delivery Site If The Contract Is Awarded. All Quotations May Be Typewritten Or Handwritten And May Be Placed In Sealed Envelope Marked Supply And Delivery Of Material Testing Equipment To Be Used In The Engineering Office Through (rfq No. 2024-_ ___________ And Must Be Delivered/submitted On___ _______ At The Bac Secretariat Office, 2f Main Building, Municipal Compound, Pinamalayan, Oriental Mindoro. Quotations Shall Be Valid For Thirty (30) Calendar Days From The Deadline Of Submission Of The Same. The Delivery Period Shall Be Within Thirty (30) Calendar Days From Receipt Of The Purchase Order (po). The Supplier Should Inform The Purchaser At Least A Day Before The Date Of Delivery. The Delivery Will Be Made Only During Working Days And Hours. Delivery Site: Municipal Engineering Office The Applicable Rate For Late Deliveries Is One Tenth (1/10) Of One Percent (1%) Of The Cost Of The Unperformed Portion For Every Day Of Delay. The Maximum Deduction Shall Be Ten Percent (10%) Of The Amount Of Contract. Once The Cumulative Amount Of Liquidated Damages Reaches Ten Percent (10%) Of The Amount Of The Contract, The Procuring Entity Shall Rescind The Contract, Without Prejudice To Other Courses Of Action And Remedies Open To It. The Prospective Supplier Shall Submit The Following: Ww) Duly Accomplished Quotation Form (annex A); And Xx) Brochures Of The Items Offered, If Any. The Municipal Government Of Pinamalayanreserves The Right To Accept Or Reject Any Quotation, And To Annul The Procurement Process And Reject All Quotations At Any Time Prior To Contract Award, Without Thereby Incurring Any Liability To The Affected Supplier Or Suppliers. Municipal Government Of Pinamalayan Also Reserves The Right To Waive Any Required Formality In The Proposals Received, And Select The Proposal Which It Determines To Be The Most Advantageous To The Government. Carlito M. Mejico, Cpa, Reb Municipal Assessor Bac Chairperson Quotation Form Rfq No. _______ Date: _____________ The Chairperson Bids And Awards Committee Municipal Government Of Pinamalayan Madrid Blvd., Zone Iii, Pinamalayan, Oriental Mindoro Sir/madam: Having Examined The Subject Request For Quotation (rfq) Including The Technical Specifications, We, The Undersigned Offer To Supply And Deliver The Following Items (with Our Unit Prices And Total Price): Item/ Lot No. Item Description No. Of Units Unit Price Total Price Lot 1 Lot 2 Lot 3 California Bearing Ratio Machine California Bearing Ratio Tester Maximum Load : 50 Kn Load Speed: 1.0/min Penetration Bar: 50.8mm X 100mm Platen Travel: 50mm Platen Dia: 170mm Mould Dia: 152mm X 170mm Dimension Size: 34 X 45 X 88 X Cm Power: 220 X 50hz 150w Weight: 82kg Concrete Slump Cone Equipment 10 X 30 X 30 Cm Concrete Beam Steel Mold 6” X 6” X 21” Steel Concrete Cylinder Steel Mold 4”x 8” Steel Concrete Cylinder Steel Mold 16”x 12” Sand Cone Apparatus Bottom Cone: 6 ½ Diameter Width: 1 Gallon Threaded Jar Width : Retachable Value With A ½ Diameter Orifice Field Density Test Apparatus 1 Pc Ladle For Scooping Soil 12 Pcs Aluminum Cans For Soil Samples 1 Gallon Container Can 1 Pc Rubber Mallet 1 Pc Sand Scoop 1pc Soft Brush 1 Pc Concrete Chisel Soil Compactor With 500x588mm Base Plate Gasoline Engine Engine Power: 6-5 Hp Weight: 127 Kg Frequency: 4300 Vpm (vibration Per Minute) Cetrifugal Force: 25kn Compactor Depth: 30cm Travel Speed:25cm/s Efficiency:500m3/hr Plate Size:50cm/58.8cm Sieve Analysis Machine With Test Sieves Sieve Brass: 3”, 2 ½ “, 2”, 1 ½’’, 1”, ¾”, ½”, ¼”, 3/8 #2, #8, #10,#12,#16, #20, #30, #80, #80, #100, #200 W/ Pan And Cover 8x2”, Wash Nsieve, #200. Fine Sieve Cleaning Brush Laboratory Drying Machine Liner Material: Stainless Steel Internal Space :35 X 35 X35 Cm External Size: 48 X 46 X 57cm Power Voltage: 800w/220v Volume:43l 1 3 3 3 3 1 1 1 1 1 Grand Total Note: Purchaser’s Specifications Are Minimum Requirements. The Bidder/supplier May Offer Higher Specifications Or Additional Items, If Any. All Items Shall Be Covered By At Least One (1) Year Warranty On Parts And Labor. (attach Additional Sheets If Necessary) We Undertake, If Our Quotation Is Accepted To Supply And Deliver The Above Goods Within Ten (10) Days From The Receipt Of Purchase Order (po). We Agree To Abide By This Quotation For A Period Of Thirty (30) Days After The Dated Deadline Of Submission Specified In Your Rfq. We Understand That Payment For Items Delivered And Installed Will Be Made To The Winning Supplier After The Inspection And Acceptance Of Goods Delivered And Installed. ____________________________________________ Canvassed By: Supplier’s/authorized Representative Signature Over Printed Name Designation: _________________________________________ Name Of Company: ____________________________________ Address: _____________________________________________ Contact Number. ______________________________________ Phil Geps Registration No.______________________________