NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY USA Tender

Nist’s Materials Measurement Laboratory (mml), Chips Metrology Program Is Tasked With Providing The Semiconductor Industry With Measurement Capabilities, Knowledge, And Open-source Data For Polymeric Materials That Are Used In Next-generation Packaging Technologies. for This Program, A High-performance Mid-wave Infrared (mwir) Camera System Is Required. The Objective Of The Metrology Program Is To Spatially Map The Temperature Evolution Of Thermosets During Thermal Cure And During Post-cure Under Relevant Operating Conditions For Packaging Materials (thermal And Humidity Cycling). The Thermoset Will Be Placed On A Thin (approximately 100 μm – 300 μm Thick), Stiff Cantilever (approximate Planar Dimensional Range: 50 Mm × 3 Mm – 100 Mm × 6 Mm) That Will Bend In Response To Cure Shrinkage And Hygrothermal Expansion/contraction. The Amount Of Bending Will Be Measured With A Laser System, Enabling The Cantilever To Act As A Sensor To Quantify The Residual Stress Induced By Dimensional Changes In The Thermoset. The Calculated Stresses Will Be Related To Temperature Fluctuations In The Material That Are Measured By The Ir Camera. An Oven Or Radiative Heaters Will Be Used To Achieve The Hygrothermal States Of Interest. These Setups Create Dimensional Constraints That Require Large, Adjustable Distances Between The Ir Camera And The Cantilever. Additionally, The Planar Dimensions Of The Cantilever Are Small, Which Necessitates An Ir Camera With High Spatial Resolution. To Study Next-generation Packaging Materials That Exhibit Rapid Cure Times, This Ir Camera Must Also Be Capable Of High-speed Operation To Capture The Temperature Evolution Of The Material. nist Is Seeking Information From Domestic Sources That May Be Capable Of Providing A Commercial Item Solution That Meets Or Exceeds One Or Both Of The Following Draft Minimum Configurations, With Optional Line Items Below: technical Specifications - Configuration 1 sensor Size – Native Sensor Resolution Must Be At Least 640 Pixels X 512 Pixels. Pixel Resolutions Gained Through Digital Enhancement Or Mechanical Shifting Of Sensors Relative To Optics Will Be Ignored. acquisition Rates maximum Frame Rate Must Achieve At Least 1004 Hz At 640 Pixels X 512 Pixels. programmable Frame Rates Must Allow For Selection From A Minimum Range Of 0.0015 Hz To 1004hz. maximum Frame Rate Of At Least 15,000 Hz For Subwindowed Frame. spatial Resolution the Spatial Resolution Described Below Must Be Achieved Without The Use Of Extender Rings Which Cause Differences In The Relative Illumination Between The Center And Edges Of The Frame. working Distance – Camera System (detector And Optics Combined) Must Have A Working Distance That Can Be Varied Continuously Between 110 Mm And 500 Mm. instantaneous Field Of View at A Working Distance Of 200 Mm, The Camera System (detector And Optics Combined) Must Have A Spatial Resolution Less Than Or Equal To 89μm/pixel. at A Working Distance Of 500 Mm, The Camera System (detector And Optics Combined) Must Have A Spatial Resolution Less Than Or Equal To 256μm/pixel. field Of View at A Working Distance Of 200mm, The Camera System (detector And Optics Combined) Must Provide A Field Of View Of At Least 50mm X 40mm. at A Working Distance Of 500mm, The Camera System (detector And Optics Combined) Must Provide A Field Of View Of At Least 160mm X 130mm. trigger – Camera System Must Provide At Least One Hardware Trigger Input Available By Bnc Or Sma Connection On The Camera Body. An Included Dongle Between A Camera Body Connector And Bnc Or Sma Meets This Requirement. spectral Range – The Mwir System Must Detect Wavelengths From 3μm To 5μm. calibration – The Camera System (detector And Optics Combined) Must Be Calibrated At A Minimum Range Of −20°c To 350°c Without Extrapolation. software Requirements at Least One Perpetual “seat” Of Analysis Software Licensing Must Be Included. The Computer Used To Control This Camera Cannot Be Connected To The Internet. Therefore, Activation Of This Seat Must Not Require An Internet Connection. Further, The Files Needed To Install And Run The Analysis Software Must Also Be Provided In A Manner That Does Not Require An Internet Connection. setting Of All User-settable Operational Parameters Including Integration Time, Sensor Windowing, Frame Rate, Filter Wheel Position, Trigger Types, Trigger Arming, Emissivity. display Of Real Time Images From The Camera For Operations Including Focusing. capturing Of Data From The Camera To The Control Pc. Both Real-time Streaming Of Data To The Pc And Local Storage On The Camera That Can Be Transferred To The Control Pc Meet This Requirement. exporting Of Data From Any Proprietary Formats To Open Formats. Inclusion Of A Software Development Kit (sdk) That Would Enable Access From Other Programming Languages Can Meet This Requirement If The Sdk Can Read The Raw Data And Any Required Metadata Including Temperature Calibration Information. defining A Region Of Interest Using A Rectangle, Circle, Line, Or Single Pixel And Creating A Time Versus Temperature Plot That Is The Mean Temperature Within That Region. Along With The Plot, It Must Be Possible To Export The Data As At Least One Of The Following Filetypes: .csv, .txt, .xls, Or .xlsx. physical connections From The Camera To The Control Pc Must Enable Data Transfer At The Highest Frame Rate Specified In “2. Acquisition Rates.” description Must Be Included That Lists The Computer Hardware (such As The Frame Grabber Card And The Pci) Required To Connect The Camera To The Computer Using Coaxpress And/or Camera Link Cables To Enable Rapid Data Transfer For High Frame Rate Data Acquisition. must Operate From A Nema 5-15r (standard Us Outlet – 120 V, 15 A). camera System (including Detector And Optics) Must Weigh Less Than 8 Kg So That It Can Be Mounted On Industrially Available Stages. camera Must Include A Filter Wheel That Holds At Least 4 Filters. memory – The Camera Must Include An On-board Solid-state Disk (ssd) With At Least 512 Gb. control Computer – A Control Computer Is Not Required. Nist Will Use Its Own Computer To Control The Camera. technical Specifications - Configuration 2 sensor Size – Native Sensor Resolution Must Be At Least 1280 Pixels X 1024 Pixels. Pixel Resolutions Gained Through Digital Enhancement Or Mechanical Shifting Of Sensors Relative To Optics Will Be Ignored. acquisition Rates maximum Frame Rate Must Achieve At Least 60 Hz At 1280 Pixels X 1024 Pixels. programmable Frame Rates Must Allow For Selection From A Minimum Range Of 0.0015 Hz To 60hz. spatial Resolution the Spatial Resolution Described Below Must Be Achieved Without The Use Of Extender Rings Which Cause Differences In The Relative Illumination Between The Center And Edges Of The Frame. working Distance – Camera System (detector And Optics Combined) Must Have A Working Distance That Can Be Varied Continuously Between 110 Mm And 500 Mm. instantaneous Field Of View at A Working Distance Of 200 Mm, The Camera System (detector And Optics Combined) Must Have A Spatial Resolution Less Than Or Equal To 45μm/pixel. at A Working Distance Of 500 Mm, The Camera System (detector And Optics Combined) Must Have A Spatial Resolution Less Than Or Equal To 128μm/pixel. field Of View at A Working Distance Of 200mm, Camera System (detector And Optics Combined) Must Provide A Field Of View Of At Least 50mm X 40 Mm. at A Working Distance Of 500mm, Camera System (detector And Optics Combined) Must Provide A Field Of View Of At Least 150mm X 110 Mm. trigger – Camera System Must Provide At Least One Hardware Trigger Input Available By Bnc Or Sma Connection On The Camera Body. An Included Dongle Between A Camera Body Connector And Bnc Or Sma Meets This Requirement. spectral Range – The Mwir System Must Detect Wavelengths From 3μm To 5μm. calibration – The Camera System (detector And Optics Combined) Must Be Calibrated At A Minimum Range Of −20°c To 350°c Without Extrapolation. software Requirements at Least One Perpetual “seat” Of Analysis Software Licensing Must Be Included. The Computer Used To Control This Camera Cannot Be Connected To The Internet. Therefore, Activation Of This Seat Must Not Require An Internet Connection. Further, The Files Needed To Install And Run The Analysis Software Must Also Be Provided In A Manner That Does Not Require An Internet Connection. setting Of All User-settable Operational Parameters Including Integration Time, Sensor Windowing, Frame Rate, Filter Wheel Position, Triggers, Emissivity. display Of Real Time Images From The Camera For Operations Including Focusing. capturing Of Data From The Camera To The Control Pc. Both Real-time Streaming Of Data To The Pc And Local Storage On The Camera That Can Be Transferred To The Control Pc Meet This Requirement. exporting Of Data From Any Proprietary Formats To Open Formats. Inclusion Of A Software Development Kit (sdk) That Would Enable Access From Other Programming Languages Can Meet This Requirement If The Sdk Can Read The Raw Data And Any Required Metadata Including Temperature Calibration Information. defining A Region Of Interest Using A Rectangle, Circle, Line, Or Single Pixel And Creating A Time Versus Temperature Plot That Is The Mean Temperature Within That Region. Along With The Plot, It Must Be Possible To Export The Data As At Least One Of The Following Filetypes: .csv, .txt, .xls, Or .xlsx. physical connections From The Camera To The Control Pc Must Enable Data Transfer At The Highest Full Frame Rate Specified Above. must Operate From A Nema 5-15r (standard Us Outlet – 120 V, 15 A). camera Module With Optics Must Weigh Less Than 8 Kg. camera Must Include A Filter Wheel That Holds At Least 4 Filters. control Computer – A Control Computer Is Not Required. Nist Will Use Its Own Computer To Control The Camera. optional Items That May Be Considered: line Item 0002 (optional): description: Extended Temperature Calibration quantity: 1 technical Specifications pricing For Calibration Up To 600°c (including All Required Equipment) May Be Provided As An Option. line Item 0003 (optional): description: All-purpose Lens quantity: 1 technical Specifications pricing For An “all-purpose” Lens That Provides Working Distances Between 500 Mm And Infinity May Be Provided As An Option. pricing For Calibrating The “all-purpose” Lens For The Temperatures Stated Previously Should Be Included As An Option. line Item 0004 (optional): description: Training quantity: 1 technical Specifications pricing For On-site Training On How To Use The Ir Camera System May Be Provided As An Option. line Item 0005 (optional): description: Customer Care Program quantity: 1 technical Specifications pricing For A Customer Care Program (that Includes At A Minimum Remote Technical Support) May Be Provided As An Option. how To Respond To This Notice in Responding To This Notice, Please Do Not Provide Proprietary Inforrmation. Please Include Only The Following Information, Readable In Either Microsoft Word 365, Microsoft Excel 365, Or .pdf Format, In The Response: Submit The Response By Email To The Primary Point Of Contact And, If Specified, To The Secondary Point Of Contact Specialist Listed At The Bottom Of This Notice As Soon As Possible, And Preferably Before The Closing Date And Time Of This Notice. provide The Complete Name Of Your Company, Address, Name Of Contact For Follow-up Questions, Their Email, Their Phone Number And, If Your Company Has An Active Registration In Https://sam.gov, Your Company’s Unique Entity Id (uei). identify Laboratory Equipment That Your Company Sells That Is Of The Nature Addressed In The Background Section Of This Notice. Include Brand Name, Make, Model, And/or Other Distinguishing Information. state If Your Company Is The Manufacturer Of The Identified Equipment Or Is A Retailer Or Wholesaler That Normally Sells The Identified Equipment. If The Latter, Indicate Whether The Manufacturer Authorized In Writing For Your Company To Sell The Identified Equipment On Behalf Of The Manufacturer. describe Performance Capabilities And Relevant Or Beneficial Physical And Functional Features For Any Equipment You Identified To Satisfy The Nist-identified Minimum Specifications Described In This Notice. identify Any Aspects Of The Nist Market Research Notice, Including Instructions, And Draft Minimum Specifications In The Background Section Above That Could Be Viewed As Unduly Restrictive Or Contain Unnecessary Barriers That Adversely Affect Your Ability To Fully Participate And Indicate Why. In Such A Scenario, Please Offer Suggestions For How The Market Research Notice And Draft Minimum Specifications Could Be Made More Inclusive And Competitive. discuss Whether The Equipment That Your Company Sells And Which You Describe In Your Response To This Notice May Be Customized To Specifications And Indicate Any Limits To Customization. for The Naics Code Listed In This Notice: indicate Whether Your Company Is (a) A Small Business Or (b) Other Than Small Business. See The Table Of Small Business Size Standards And The Associated .pdf Download File For Small Business Size Standards And Additional Information. if You Believe The Naics Code Listed In This Notice Is Not The Best Naics Code For The Type Of Product Addressed In This Notice, Identify An Alternative Naics Code That You Believe Would Be More Appropriate For The Planned Procurement. describe Services That Are Available With The Purchase Of The Aforementioned Equipment From Your Company Such As Installation, Training, And Equipment Maintenance. describe Standard Terms And Conditions Of Sale Offered By Your Company For The Aforementioned Equipment Such As: Delivery Time After Your Company Accepts The Order; Fob Shipping Terms: Manufacturer Warranty (including Details Regarding Nature And Duration); If Available, Description(s) Of Available Extended Warranty; Equipment Setup And Test; Operator And Service Instruction Manual(s); Cleanup After Installation; And If Applicable, Other Offered Services. Provide A Copy Of Manufacturer Standard Terms And Conditions That Typically Relate To The Sale Of The Specified Equipment, If Available. state Whether Your Company Offers Facility Renovation Services Related To Installation Of The Aforementioned Equipment At Its Delivery Destination, If Required Per The Nist-identified Minimum Specifications, And Provide Description Of Services. Indicate If Your Company Performs The Facility Renovation Services Or Typically Subcontracts The Work To Another Company. Indicate If Your Company Would Be Interested Inspecting The Intended Installation Site During The Market Research Phase. state Published Price, Discount Or Rebate Arrangements For Aforementioned Equipment And/or Provide Link To Access Company’s Published Prices For Equipment And Services. state Whether The Aforementioned Equipment Is Manufactured In The United States And, If Not, State The Name Of The Country Where The Equipment Is Manufactured. identify Any Plans/possibilities For Changes In Manufacturing Location Of The Aforementioned Equipment And Provide Relevant Details. if The Aforementioned Equipment And Related Services Are Available For Purchase On Any Existing Federal Supply Schedule Contract(s) Or Other Contracts Against Which Nist May Be Able Place Orders, Identify The Contract Number(s) And Other Relevant Information. identify Any Customers In The Public Or Private Sectors In Which You Provided The Aforementioned Or Similar Equipment. Include Customer(s) Information: Company Name, Phone Number, Point Of Contact, Email Address. provide Any Other Information That You Believe Would Be Valuable For Nist To Know As Part Of Its Market Research For This Requirement. state If You Require Nist To Provide Additional Information To Improve Your Understanding Of The Government’s Requirement And/or Would Like To Meet With Nist Representatives To Discuss The Requirement And The Capabilities Of The Identified Equipment. questions Regarding This Notice questions Regarding This Notice May Be Submitted Via Email To The Primary Point Of Contact And The Secondary Point Of Contact Listed In This Notice. Questions Should Be Submitted So That They Are Received By 11:00 A.m. Eastern Time On October 31, 2022. Questions Will Be Anonymized And Answered Via Sources Sought Notice Amendment Following The Question Submission Deadline. important Notes the Information Received In Response To This Notice Will Be Reviewed And Considered So That Nist May Appropriately Solicit For Its Requirements In The Near Future. this Notice Should Not Be Construed As A Commitment By Nist To Issue A Solicitation Or Ultimately Award A Contract. responses Will Not Be Considered As Proposals Or Quotations. no Award Will Be Made As A Result Of This Notice. nist Is Not Responsible For Any Costs Incurred By The Respondents To This Notice. nist Reserves The Right To Use Information Provided By Respondents For Any Purpose Deemed Necessary And Appropriate. thank You For Taking The Time To Submit A Response To This Request!