DEPT OF THE NAVY USA Tender

The Purpose Of This Synopsis Is To Provide Notice Of Naval Information Warfare Center (niwc) Atlantic's Intent To Award A Firm-fixed-price Purchase Order On A Noncompetitive Basis To Climax Portable For 1 Climax 105215 Flange Facer, Model Ff8200 Id Chuck Hyd Turning Arm C-weight Metal 1ea2 Hp 93724 Laptop, Model Hp1000 208-230v Controls Pendant C050 H050 1ea. The Government Intends To Negotiate Solely With Climax Portable Under The Authority Of Far 13.106-1(b). A Request For Information Was Posted To The Government Point Of Entry On 9/18/2024 Until 10/9/2024 For The Following Requirement For The Flange Facer And Hpu Of Armored Military Vehicles. Machine Performance Rangesid Mounting Range45 - 120 Inches (1143.0 - 3048.0 Mm)facing Diameter Range 45 - 120 Inches (1143.0 - 3048.0 Mm)milling Diameter Range 45 - 120 Inches (1143.0 - 3048.0 Mm)grinding Diameter Range 45 - 120 Inches (1143.0 - 3048.0 Mm)swing Diameter @ Minimum With Feedbox On End Of Arm84.7 Inches (2151.4 Mm)radial Tool Slide Travel 12 Inches (304.8 Mm)axial Tool Head Travel 4 Inches (101.6 Mm)depth Required Inside Bore For Id Chuck (± 0.25 Inches (± 6.4 Mm) Is Travel Of Leveling Foot)12.13 ± 0.25 Inches (308.1 ± 6.4 Mm)feed Rate 0.002 - 0.040 In/rev (0.051 - 1.016 Mm/rev)rotational Drive Systemdrive Type Hydraulic Drive Withpinion And Internal Ring Gearpinion Gear To Ring Gear Reduction 7.429:1single Point Turning Speed Range:2.8 - 14 Rpmmilling & Grinding Speed Ranges (with 150:1 Reducer):0.002 - 0.374 Rpmpower Input Requirements10 Gpm@1200 Psi 37.9 L/min @ 8273 Kpatesting Data - Flatness At 82 Inch (2083 Mm) Diameter: 0.0068 Inches (0.17 Mm)on A Dedicated Fixture Made Of A-36 Steel In A Controlled Environment With Single Point Machine, After Warm-up.tool Configurationssingle-point Machining Only1. Base Packagerotary Table, Tool Kit, Operator's Manual 2. Feed Assemblypneumatic Feed Assembly W/ Remote Air Control 3. Drive Motor Assemblyhydraulic Drive Assy W/ Feed Conditioning Unit - Does Not Include Motor(hydraulic Drive System Includes: Hyd Motormount, Hoses, Fittings, Rotary Union, Feed Trip Valve,cam, And Feed Pneumatic Conditioning Unit.)4. Hydraulic Motor For Rotary Table Drive (if Hydraulic Drive Isselected In Step 3). Rated At 10 Gpm, 1200 Psi18.7 Cu In (306.4 Cu Cm), 2.8 - 14 Rpm 5. Turning Arm Assemblyturning Arm Assembly With Single Point Tool Head 6. Counterweight Assemblycounterweight Assembly 7. Chuck Assemblyid Chuck Assembly 8. Shipping Containermetal Container For Id Mount Machinehydraulic Power Units For Single Pointinghorsepower 10 Hpgpm Flow / Hz 10 Gpm @ 60 Hz 8.36 Gpm @ 50 Hzspeedto Be Rated For 15gpm (56.7 L/min) Max Continuous Use, 20 Gpm (75.7 L/min) Max Intermittent Use. Intermittent Is Defined As 10% Of Each Minuteoperating Range-10°f ( –23°c) - 200°f (93°c)oil Temperature Range50°f (10°c) - 190°f (88°c)cordset/hose Length 50 Ft (15m)hydraulic Quick Disconnect Couplingsiso 16028control Functions System Start, E-stop, Jog, And Remote Speed Dial Controloperator Pendant Accessory Needed Functions:-remote Pendant-3 Axis Pendant Control-hydraulic Locking Feature-built-in System Relief Valve And System Pressure Gauge-osha Compliant-speed Control Allowing The Operator To Set Repeatable Speed Settings And Easily Make Small Speed Adjustments When Needed.-soft Start/stop Control Ensuring Smooth Starting And Stopping On Large Machines, Preventing Damage To The Drive And Feed.-controlled Deceleration Preventing Over-pressurization Of The Hydraulic System Allowing The Operator To Decelerate The Machine Tool In A Safe And Controlled Manner, Especially When The "emergency Stop" Is Used.-controlled Motion Of The Machine Tool Minimizing Sudden Speed Changes Preventing Rapid Acceleration When A Cutting On Uneven Surfaces-replaceable Cordset With Quick Connectors At Both Ends Of The Cable.-magnetic Back Allowing For Convenient Positioning Of The Pendant And Preventing Pendant From Falling.-ergonomic Pistol Grip For Ease Of Use.*laptop Is Custom Built For Oem And Cannot Be Bought From Hp Commercially. Must Purchase Through Climax To Ensure Form Fit Function With Machinery The Naics Code Is 333517and The Small Business Size Standard Is 500 Employees. This Notice Is Not A Request For Competitive Quotes; However, Any Responsible Source Believing That It Can Fulfill The Requirement May Submit A Capability Statement, Proposal, Or Quotation. Responses To The Pre-solicitation Notice Can Be Submitted Via The Navwar E-commerce Website At Navwar E-commerce Central (navy.mil) By 31 January 2025. Questions Concerning This Notice Should Be Directed To William Faulconer At William.a.faulconer.civ@us.navy.mil. All Responses Received By 31 January 2025 Will Be Considered By The Government For The Purpose Of Determining Whether To Conduct A Competitive Procurement. A Determination By The Government Not To Compete The Proposed Purchase Order Based Upon Responses To This Notice Is Solely Within The Discretion Of The Government.