DEFENSE LOGISTICS AGENCY USA Tender

Amc/amsc: 1g 1 Suitable For Competitive Acquisition. (see Notes 1 And 2) g The Government Has Unlimited Rights To The Technical Rights To The Technical Data, And The Data Package Is Complete. Valid Amcs: 1 And 2. drawings – item Name: Circuit Card Assembly rp001: Dla Packaging Requirements For Procurement rd002, Covered Defense Information Applies ra001: This Document Incorporates Technical And/or Quality Requirements (identified By An 'r' Or An 'i' Number) Set Forth In Full Text In The dla Master List Of Technical And Quality Requirements Found On The Web at: http://www.dla.mil/hq/acquisition/offers/eprocurement.aspx for Simplified Acquisitions, The Revision Of The Master In Effect On The solicitation Issue Date Or The Award Date Controls. For Large acquisitions, The Revision Of The Master In Effect On The Rfp Issue Date applies Unless A Solicitation Amendment Incorporates A Follow-on revision, In Which Case The Amendment Date Controls. rq009: Inspection And Acceptance At Origin rq011: Removal Of Government Identification From Non-accepted Supplies rq032: Export Control Of Technical Data this Item Has Technical Data Some Or All Of Which Is Subject To export-control Of Either The International Traffic In Arms Regulations (itar) Or The Export Administration Regulations (ear), And Cannot Be exported Without Prior Authorization From Either The Department Of State or The Department Of Commerce. Export Includes Disclosure Of Technical data To Foreign Persons And Nationals Whether Located In The United states Or Abroad. This Requirement Applies Equally To Foreign National employees And U.s. Companies And Their Foreign Subsidiaries. Dfars 252.225-7048 Is Applicable To This Data. the Defense Logistics Agency (dla) Limits Distribution Of Export-control technical Data To Dla Contractors That Have An Approved Us/canada Joint certification Program (jcp) Certification, Have Completed The introduction To Proper Handling Of Dod Export-controlled Technical Data training And The Dla Export-controlled Technical Data Questionnaire (both Are Available At The Web Address Given Below), And Have Been approved By The Dla Controlling Authority To Access The export-controlled Data. Instructions For Obtaining Access To The export-controlled Data Can Be Found At: https://www.dla.mil/logistics-operations/enhanced-validation/ to Be Eligible For Award, Offerors And Any Sources Of Supply Proposed for Use Are Required To Have An Approved Jcp Certification And Have been Approved By The Dla Controlling Authority To Access export-controlled Data Managed By Dla. Dla Will Not Delay Award In order For An Offeror Or Its Supplier To Apply For And Receive Approval by The Dla Controlling Authority To Access The Export-controlled Data. rq039: Non-tailored Higher-level Quality Requirements (sae As9100) For manufacturers And Non-manufacturers rt001: Measuring And Test Equipment part Name Assigned By Controlling Agency: Circuit Card Assembly, Phase shifter Driver Electro-static Sensitive Device mil-std-130n(1) Dated 16 Nov 2012. identification Marking Of U.s. Military Property mercury Or Mercury Containing Compounds Shall not Be Intentionally Added To<(>,<)> Or Come In Direct contact With<(>,<)> Any Hardware Or Supplies Furnished under This Contract. Exception: Functional Mercury used In Batteries, Fluorescent Lights, Required instruments; Sensors Or Controls; Weapon Systems; and Chemical Analysis Reagents Specified By Navsea. portable Fluorescent Lamps And Portable Instruments containing Mercury Shall Be Shock Proof And Contain a Second Boundary Of Containment Of The Mercury Or mercury Compound. (iaw Navsea 5100-003d). reference Control Part Number 7624570 Cage 53711 sampling: the Sampling Method Shall Be In Accordance With Mil-std-1916 Or Asq h1331, Table 1 Or A Comparable Zero Based Sampling Plan Unless Otherwise specified By The Contract. If The Applicable Drawing, Specification, standard, Or Quality Assurance Provision (qap) Specifies Critical, Major and/or Minor Attributes, They Shall Be Assigned Verificaiton Levels Of vii, Iv And Ii Or Aqls Of 0.1, 1.0 And 4.0 Respectively. Unspecified attributes Shall Be Considered As Major Unless Sampling Plans Are specified In Applicable Documents. For Mil-std-1916, The Manufacturer may Use The Attribute Or Variable Inspection Method At Their Option Or per The Contract. Mil-std-105/asq Z1.4 May Be Used To Set Sample Lot size, But Acceptance Would Be Zero Non-conformances In The Sample Lot unless Otherwise Specified In The Contract. overall Length: 5.740 Inches Nominal Overall Width: 1.619 Inches Nominal major Components: Connector Assy, Electrical (7624566-2/53711) 1; printed Wiring Board, Phase Shifter Driver, 1; No Keying Pins Special features: No Keying Pin; Model With Keying Pin Is 7624570-1. End Item identification: As-4108/spy Phased Array Antenna critical Application Item iaw Basic Drawing Nr 53711 7624570 revision Nr D Dtd 06/21/2011 part Piece Number: iaw Reference Drawing Nr 53711 7624570 revision Nr F Dtd 02/06/2009 part Piece Number: iaw Reference Drawing Nr 10001 2900594 revision Nr Ae Dtd 12/01/2014 part Piece Number: iaw Reference Drawing Nr 10001 3256939 revision Nr P Dtd 02/28/2013 part Piece Number: iaw Reference Drawing Nr 53711 7624560 revision Nr A Dtd 06/19/2013 part Piece Number: iaw Reference Drawing Nr 53711 7624561 revision Nr B Dtd 01/30/2018 part Piece Number: iaw Reference Drawing Nr 53711 7624562 revision Nr C Dtd 05/08/2019 part Piece Number: iaw Reference Drawing Nr 53711 7624563 revision Nr L Dtd 03/10/2017 part Piece Number: iaw Reference Drawing Nr 53711 7624565 revision Nr Dtd 09/22/2005 part Piece Number: iaw Reference Drawing Nr 53711 7624566 revision Nr G Dtd 02/21/2020 part Piece Number: iaw Reference Drawing Nr 53711 7624567 revision Nr A Dtd 01/15/2007 part Piece Number: iaw Reference Drawing Nr 53711 7624569 revision Nr C Dtd 08/19/2009 part Piece Number: iaw Reference Drawing Nr 53711 7624573 revision Nr D Dtd 10/17/2023 part Piece Number: iaw Reference Drawing Nr 53711 7624574 revision Nr B Dtd 09/07/2011 part Piece Number: iaw Reference Drawing Nr 53711 7624575 revision Nr C Dtd 06/25/2020 part Piece Number: iaw Reference Drawing Nr 53711 7624576 revision Nr D Dtd 11/07/2018 part Piece Number: iaw Reference Drawing Nr 53711 7624578 revision Nr A Dtd 05/15/2013 part Piece Number: iaw Reference Drawing Nr 53711 7624581 revision Nr Dtd 05/13/2004 part Piece Number: iaw Reference Drawing Nr 53711 7624583 revision Nr A Dtd 07/11/2016 part Piece Number: iaw Reference Drawing Nr 53711 7624590 revision Nr A Dtd 02/13/2018 part Piece Number: iaw Reference Drawing Nr 53711 7624591 revision Nr B Dtd 05/23/2017 part Piece Number: iaw Reference Drawing Nr 53711 7624592 revision Nr A Dtd 06/30/2008 part Piece Number: iaw Reference Drawing Nr 53711 7624593 revision Nr C Dtd 05/10/2018 part Piece Number: iaw Reference Drawing Nr 53711 7624596 revision Nr B Dtd 06/28/2013 part Piece Number: iaw Reference Drawing Nr 53711 7624597 revision Nr A Dtd 06/13/2006 part Piece Number: iaw Reference Drawing Nr 53711 7624598 revision Nr C Dtd 05/14/2020 part Piece Number: iaw Reference Drawing Nr 53711 7624599 revision Nr B Dtd 09/07/2011 part Piece Number: iaw Reference Drawing Nr 53711 7624600 revision Nr C Dtd 01/10/2018 part Piece Number: iaw Reference Drawing Nr 53711 7624602 revision Nr C Dtd 01/10/2013 part Piece Number: iaw Reference Drawing Nr 53711 7624603 revision Nr C Dtd 07/01/2010 part Piece Number: iaw Reference Drawing Nr 53711 7624604 revision Nr A Dtd 01/10/2013 part Piece Number: iaw Reference Drawing Nr 53711 7624605 revision Nr Dtd 09/22/2005 part Piece Number: iaw Reference Drawing Nr 53711 8306492 revision Nr B Dtd 08/21/2020 part Piece Number: iaw Reference Drawing Nr 10001 Ws10288 revision Nr Ab Dtd 04/05/2001 part Piece Number: iaw Reference Drawing Nr 10001 Ws10298 revision Nr Dtd 06/29/1983 part Piece Number: please Review The Nsn Listed Above And Provide Any Sources That May Be Able To Manufacture These Items. The Approved Sources For This Nsn Are Currently Listed Above. All Information May Be Submitted Directly To The Contract Specialist Listed Above. This Information Must Be Provided By The Response Date Indicated Above. in Order To Be Considered An Interested Party, Vendors Must Complete And Return The Attached Market Survey To The Contract Specialist Listed Above By The Required Response Date. note: This Project Contains Drawings/specifications. You May Access The Tdp Directly From Cfolders And Searching For The Above Cited Solicitation Number. you May Access Them Only Through The Following Link: Https://pcf1.bsm.dla.mil/cfolders. the Drawings Cannot Be Accessed Through Dibbs. thank You In Advance For Your Assistance.