Drawer Tenders

Description: BOQ ITEMS: Clearing jungle including uprooting of rank vegetation grass brush wood trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. , Demolishing R.C.C. work manually by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge., Demolishing brick work manually by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge. In cement mortar, Earth work in excavation by mechanical means Hydraulic excavator manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil., Excavation work by mechanical means Hydraulic excavator manual means in foundation trenches or drains not exceeding 1.5m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soils as directed within a lead of 50 m Hard Rock, Filling available excavated earth excluding rock in trenches plinth sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m, Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level 1 isto 3 isto 6 where 1 Cement 3 coarse sand zoneIII 6 graded stone aggregate 20 mm nominal size, Supply mix place in position compact and cure cement concrete 1 isto 2 isto 4 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size below foundations walls wells pits trenches etc. and in basin lining as per specifications drawings and directions of the Engineer incharge and including cost of centring and shuttering and cement., Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing and reinforcement All work up to plinth level 1 isto 1.5 isto 3 where 1 cement 1.5 coarse sand zoneIII 3 graded stone aggregate 20 mm nominal size , Brick work with common burnt clay F.P.S. non modular bricks of class designation 7.5 in foundation and plinth in Cement mortar 1 isto 6 1 cement 6 coarse sand, Centering and shuttering including strutting propping etc. and removal of form for Foundations footings bases of columns etc. for mass concrete, Steel reinforcement for R.C.C. work including straightening cutting bending placing in position and binding all complete upto plinth level Thermo Mechanically Treated bars of grade Fe500D or more, 15 mm cement plaster on the rough side of single or half brick wall of mix 1 isto 6 1 cement 6 fine sand Rates for external plastic are for height upto 10m from ground level in less otherwise stated, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work a. 15 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work b. 20 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work c. 25 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work d. 50 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC, Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end 20 mm nominal bore, Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end 25 mm nominal bore, Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end 50 mm nominal bore, Constructing masonry Chamber 30 into 30 into 50 cm inside in brick work in cement mortar 1 isto 4 1 cement 4 coarse sand for stop cock with C. I. surface box 100 into 100 into 75 mm inside with hinged cover fixed in cement concrete slab 1 isto 2 isto 4 mix 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size ic necessary excavation foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement 3 coarse sand 12mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. non modular bricks of class designation 7.5, Constructing masonry Chamber 60 isto 60 isto 75 cm inside in brick work in cement mortar 1 isto 4 1 cement 4 coarse sand for sluice valve with C.I. surface box 100mm top diameter 160 mm bottom diameter and 180 mm deep inside with chained lid and RCC top slab 1 isto 2 isto 4 mix 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size ic necessary excavation foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40 mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement 3 coarse sand 12 mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. non modular bricks of class designation 7.5, Constructing masonry Chamber 90 into 90 into 100 cm inside in brick work in cement mortar 1 isto 4 1 cement 4 coarse sand for sluice valve with C.I. surface box 100 mm top diameter 160 mm bottom diameter and 180 mm deep inside with chained lid and RCC top slab 1 isto 2 isto 4 mix 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size ic necessary excavation foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40 mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement 3 coarse sand 12 mm thick finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. non modular bricks of class designation 7.5, Supply and laying of HDPE Pipe line 110mm dia complete in all respect as per direction of EIC

Description: BOQ ITEMS: Model showing relation of fimbriae and ovary, 9 day human blastocyst, 12 day human blastocyst, 13 day human blastocyst, Preovulatory follicle, Ovulation, Corpus luteum, Transverse sections through at various stages of development set of 3 models (A), Transverse sections through at various stages of development set of 3 models (B), Dorsal view of human embryo showing somites set of 2 models (A), Lateral view of human embryo showing bulging pericardial area set of 3 models(A), Lateral view of human embryo showing bulging pericardial area set of 3 models(C), Transverse section showing mesodermal germ layer set of 4 models (A), Transverse section showing mesodermal germ layer set of 4 models (B), Transverse section showing mesodermal germ layer set of 4 models (C), Ovum with board, Development human embryo 22nd days, Ovary with child, Development embryonic ovulation set of 5 models, Embryonic placenta previa set of 3 models, Embryo neural groove 26 days, Development embryo set of 10 models, Development of embryonic early blastocyst set of 4 models, The uterus at the time of implementation, Primordial follicle consisting of a primary oocytes surrounded by a layer of flattened epithelial cells on board (A) Primordial follicle, Primordial follicle consisting of a primary oocytes surrounded by a layer of flattened epithelial cells on board(B) Growing follicle , Type a spermatogonia derived from the spermatogonal stem cell population represent the firstcells in the process of spermatgenesis set of 43 models on board, Abnormal germ cells primordial follicle with two oocytes , Abnormal germ cells trinucleated oocytes , Abnormal germ cells various types of abnormal spermatozoa set of 5 models on board, Development of dizygotic twins normally each embryo has its own amnion chorion and placenta set of 8 models on board, Possible relations of fetal membranes in monozygotic twins set of 12 models on board, Fertilization pathway a succession of steps After a sperm binds to the zona pellucida set of five models on board, Development of embryo showing structures Passing through the primitive umbilical ring A) 5-week embryo , The intraembryonic coelom prior to body folding set of 5 model (3d), Successive stages in development of the respiratory four gut. (3d) a. at the end of the third week , uccessive stages in development of the respiratory four gut. (3d) forth week , Development of the chief branchi of the human lungs set of 6 models on board, Histological and functional , Various types of esophageal , Successive stages in development , Ventral view of coronal section of heart at level of atrioventricular canal showing development of veinous valves a, b, Development of conotruncal ridge & closure of interventricular foramen a , Development of viteline vein, umbilical vein a , c (2d), Development of viteline vein, umbilical vein a , b, c, d (3d), Development of inferior vena cava, Development of inferior vena cava, Development of inferior vena cava, Development heart 7 somites embryo, Development heart (set of 11 models) on the stand (3d), Transformation of the pericardioperitoneal canals into the pleural cavities set of 2 models (A), Embryonic aortic arch set of 3 models on stand (3d), Developments of the inferior vena cava azygos vein &superior (3d) vena cava Seventh week , Developments of the inferior vena cava azygos vein &superior (3d) vena cava The venous system at birth , Developments of the inferior vena cava azygos vein &superior (3d) vena cava Double inferior vena cava at the lumber level (clinical correlate) , Developments of the inferior vena cava azygos vein &superior (3d) Absent inferior vena cava (clinical correlate), Fetal circulation before birth (3D), Human circulation after birth (3D), Embryonic aortic arches 4th & 6th week a b, Embryonic aortic arch set of 3 models on board (2D), Primitive dosal & ventral mesentery (3d), Anterior view of intestinal loop showing coiling of small intestine set of 2 models, Rotation of midgut set of 7 models a, b, c, d, e, f, g, (big size) on stand (3d), Development of pancreas set of 5 models with stand, Development of embryo 4th and 5th weeks set of 2 models a b on stand (3d), Development stomuch embryo with pancreas and gall bladder (3d), Stomach nerve cutting section, Development of diaphragm set of 3 models A, Development of diaphragm set of 3 models B, Folding of caudal end of the embryo a b c, Body folding changes the shape of the intraembryonic coelom a, b, c, Separates the pericardial cavity from pleural cavity a, b, c, In the future thoracic region the septum transversum froms a ventral portion, Development of Digestive System , Intermediate mesoderm of pronephric, Relation of hindgut & cloaca (3d), Genital duct in male and female a, c with board, Sagittal section showing formation of uterus & vagina a b c, Vesico urethral portion of endodermal cloaca showing the sinus tubercle & fused paramesonephric duct (3d), Development of urogenital sinuss & formation of trigone of the bladder a, b, c, d (3d), Development of renal pelvis (kideny) set of 4 models a b d on stand (3d), Divisions of the cloaca into the urogenital sinus and ano rectal canal set of 3 models on stand (3d), The urethra is open on the ventral surface of the penis, Development of the external genitalia in the female & in the new born set of 2 models on board, Development of the external genitalia in the female on board., Development of the peritoneum (3d), Ascent of the kidney set of 3 models with stand a b c (3d), Indifferent stages of the external genitalia a b, Development of external genitalia in the male at 10 weeks set of 7 models, Hypospadias showing the various locations of abnormal urethral, Development of the external genitalia in the female at 5 months a b, Urorectal & rectovaginal fistulas set of 4 model, Pharyngeal arches with board, Frontal view of embryo showing stomodeum nasal placodes on frontonasal process A, Development of face a , c, d with board, Development of palate & roof of mouth set of 6 model (A,C,D,E,F), Frontal aspect of face showing nasal prominence maxillary prominence (A), Development of face cut section showing pharyngeal archs (3d), Development of the pharyngeal arches (a, b) , Thyroglossal cyst, Frontal section through the head of a 6.5 week embryo a b, Frontal section through the head of a 7.5 week embryo a b, Frontal section through the head of a 10 week embryo a b, Intermaxillary segment and maxillary processes a b, Development brain embryo -3D, Development of human brain (embryo) about mm (3d), Development brain (embryo) three month old(3d), Development brain (embryo) 13.6 mm long medial surface (3d), Development brain (embryo) about 10.2 mm (3d), Development brain (embryo) 13.6 mm long hind brain (3d), Development brain (embryo) set of 6 models (3d) A,B,D,E, Drawings illustration a variety of NTDS involving the spinal cord a b c d e, Neural crest cells penetrating the fetal cortex of the suprarenal gland a b, Sagittal section through the cephalic part of a 6 week embryo & 11TH & 16th week a b c, Formation of Ventral motor & dorsal sensory horns A B on board, Formation of the vertebral column at various stages of development a b c, Ventrolateral view of the optic cup & optic stalk of a 6 week embryo a b c

Details: CATEGORY: BIG PLASTIC TRAY , MEDIUM PLASTIC TRAY , Kidney Tray , SPUTUM CUP , Measuring glass 200ml , Ampoule Cutter , TABLET CUTTER , Motor and pistol medium , Plastic Hair Comb Large , Comb Large , Medium Silver Tray with Lid , SS Small Bowl , Stainless Still Medium Bowl , Silver Glass 250 ml , Stainless small kidney Tray , Artrey Forcep , Thumb forcep , Sponge Holding Forcep , Steel scissors , Lock and Key Medium , Rubber Mackintosh Sheet , DRAW SHEET , SPONGE TOWEL , OT TOWEL GREEN , BIG SHEET WHITE , DIGITEL THERMOMETER , BP APPARATUS , Weighing Machine , Steel Tray with cover big , Medium Size tray with Lid , Steel Tray with cover small , Steel Kidney tray , Stethiscope , Breast Pump , Doppler with bateries , Fetoscope , soap Tray , Sponge Holder Medium , InchTape , SS Bowl Small , SS Bowl big , SS Tray Big , Ss Tray Medium , SS Basin , SS Kidney tray Steel , Plastic kidney tray , Enamel Kidney tray , Sputum mug , SS Basin medium , SS Basin Large , Enamel tray Medium , plastic mug , pint measurer , SS Tray Large , Enamel Bowl , Feeding cup , INJECTION TRAY WIT LID , Tuning Fork , Percussion Hammer , Glucometer , foetal dopler , Glucometer strips 100 strip , Haemoglobinometer with microslides , Lancet , Aneroid BP appratus , Electric Steamer , steel Spoon , Cervical Collar , pelvic collar , CRASH CART TROLLEY , wheel chair , strecher , SPENCER WELLS ARTREY FORCEP 5 , WELLS ARTREY FORCEP 6 , SPENCER WELLS ARTREY FORCEP 7 inch , KOCHERS ARTREY FORCEP STRAIGHT 8 inch , KOCHERS ARTREY FORCEP CURVED 8 inch , DEBAKEY KELLY ARTREY FORCEP STRAIGHT 7 inch , DEBAKEY KELLY ARTREY FORCEP CURVED 7 inch , DISSECTING FORCEP PLAIN 6 inch , DISSECTING FORCEP TOOTH 6 inch , DISSECTING FORCEP TOOTH 7 inch , DISSECTING FORCEP TOOTH 8 inch , DISSECTING FORCEP TOOTH 10 inch , BP HANDLE 3 number size , BP HANDLE 4 number , ADSON FORCEP PLAIN 5 inch , ADSON FORCEP THOOTH 5 inch , MAYO HEAGERS NEEDLE HOLDER STRAIGHT 6 inch , MAYO HEAGERS NEEDLE HOLDER STRAIGHT 7 , MAYO HEAGERS NEEDLE HOLDER STRAIGHT TUNGSTEN CARBIDE 7 , RYDER NEEDLE HOLDER TUNGSTEN CARBIDE 6 , IRIS SCISSOR STRAIGHT 5 , METZABAUM SCISOR STRAIGT 7 , MAYO SCISSORS CURVED 7 inch , MAYO SCISSORS CURVED TUNGSTEN CARBIDE 7 , DRESSING SCISSORS SHARP BLUNT 6 , LISTRE BANDAGE CUTTING SCISSORS 7 , HYSTRECTOMY MAINGOT FORCEP STRAIGHT 6 , HEANYS HYSTRECTOMY FORCEP SINGLE THOOTH 6 , CHEATLE FORCEP 10 , LYGENBACK RETRACTOR SMALL 35X15 , LYGENBACK RETRACTOR LARGE 45X20 , MORRIS RETRACTOR 2 , KELLY RECTAL SPECULAM M , GREEN ARMYTAGE M , SPONGE HOLDING FORCEP M , OVEM FORCEP CURVED M , UTERINE VULSELLUM M , HEGAR DIALATORS FIND half MM , HYSTOGRAPHI CANULA W L SET 3 , MIDWIFERY FORCEP SIMPSON M size , CERVICAL BIOPSY PUNCH FORCEP M size , SIMS SPECULAM M Size , CUSCO VAGINAL SPECULAM M size

Details: CATEGORY: ALLEN KEY SET , CALLIPER INSIDE SPRING , CALIPER OUTSIDE SPRING , DIVIDERS SPRING , ELECTRICIAN SCREW DRIVER , HAMMER BALL PEEN , HANDLS FILE FOR SECOND CUT , PHILIPS SCREW DRIVER SET OF 5 , PLIERS COMBINATION , SPANNER DE SET OF 12PCS , SPANNER SOCKET , STEEL RULE , CHISEL FLAT , WIRE CUTTER AND STRIPPER , ADJUSTABLE SPANNER , DRILL TWIST , ELECTRIC SOLDERING IRON , ENGINEES SQUARE , FEELER GAUGE , FILE FLAT BASTARD 200MM , FILE HALF ROUND 2ND CUT 200MM , FILE SQUARE 2ND CUT 200MM , FILE SQUARE ROUND 300MM , FILE TRAINSGULAR 2ND CUT 150MM , FLAT FILE 2ND CUT 250MM , FLAT FILE BASTRAD350MM , DRIFT PUNCH COPPER , HACKSAW FRAME , HAMMER CHIPPING , HAMMER COPPER WITH HANDLE , HAMMER MALLET , INSULATED SCREW DRIVER , MAGNETO SPANNER SET , PISTON RING GROOVE CLEANER , PLIERS FLAT NOSE , PLIERS ROUND NOSE , PLIERS SIDE CUTTING , PUNCH LETTER 4MM , SCRAPER TRAINGULAR , SPANNER T FLOCKS , SPANNER ADJUSTABLE , SPARK PLUG SPANNER , STUD REMOVER , TORQUE WRENCH , VACCUM GAUGE , VALVE SPRING COMPRESSOR , VERNIER CALIPER , STEEL MEASURING TAPE , AUTO ELECTRICAL TEST BENCH , BATTERY CHARGER , CAR JET WASHER , BLOW LAMP , BELT TENSIONER GAUGE , CHAIN PULLEY BLOCK , COMPRESSION TESTING GAUGE , CYLINDER LINER , DIFFERENT ENGINE BEARING MODEL , DIFFRENT PISTON MODEL , FUEL FEED PUMP , ENGINEES STHETHOSCOPE , GREASE GUN HEAVY DUTY , LIFTING JACK SCREW , MULTIMETER DIGITAL , AUTOMOTIVE OIL PUMP , RADIATOR CUT SECTION CROSS FLOW , RADIATOR CUT SECTION DOWN FLOW , RADIATOR PRESSURE CAP , SURFACE GAUGE WITH DIAL , TACHOMETER , TANDEM MASTER CYLINDER , THERMOSTAT , TIMING LIGHTER , TURBOCHARGER CUT SECTION , AUTOMOTIVE WATER PUMP , WORK BENCH , WORKING MODEL AIR BRAKE ASSEMBLY , ALTERNATOR ASSEMBLY , CUT SECTION TRANSMISSION GEAR BOX , CUT SECTION CENTRIFUGAL CLUTCH , DEMONSTRATION BOARD OF ELECTRONIC IGNITION SYSTEM , DEMONSTRATION BOARD OF MPFI SYSTEM , DISC BRAKE IN WORKING CONDITION , DRUM BRAKE ASSEMBLY , FUNCTIONAL MODEL OF DIFF SENSOR , STEERING ASSEMBLY , TUBELESS TYRE CARS TRUCK , TYRE SPLIT RIM WHEEL , WORKING MODEL OF POWER WINDOWS , AIR CONDITIONED CRDI VEHICLE IN RUNNING CONDITION , AUTOMOTIVE EXHAUST FIVE GAS ANALYSER AND DIESEL SMOKE METER , DIESEL ENGINE CRDI FOUR STROKE FOR DISMANTLING , DIESEL ENGINE RUNNING CONDITION STATIONARY TYPE , HYDRAULIC JACK HI LIFT , MULTISCAN TOOLS TO SCAN ENGINE , WORKING CONDITION OF DIESEL ENGINE CRDI FOUR STROKE FAULT SIMULATION , CUT SECTON OF FOUR BYE SIX CYLINDER DIESEL ENGINE , DIESEL ENGINE SIX CYLINDER IN RUNNING CONDITION , FOUR STROKE PETROL ENGINE WITH CNG SETUP , MPFI PETROL ENGINE WITH SWIVELING STAND , PETROL ENGINE TWO STROKE , TYBE TYRE VULCANIZING MACHINE , TWO POST CAR LIFT CAP 4000KG , WHEEL ALLIGNMENT MACHINE , WHEEL BALANCING MACHINE , WORKING CONDITION OF PETROL MPFI ENGINE FAULT , CARBURETOR SOLEX MIKUNY , CUT SECTION MODEL OF ELECTRICAL SYSYTEM WORKING MODEL , HEAVY COMMERICIAL VEHICLE , CYLINDER BORE GAUGE CAPACITY , MINI DRAFTER , SET SQUARE , DRAUGHTSMAN DRAWING BOX

Details: CATEGORY: dia GI Tubing medium grade 1 point 5 Mtr Long Make Jindal or Tata or Kalinga , Service cable PVC insulated aluminium conductor 1100 volt grade Heavy duty served with inner service connection 10 Sqmm 2 core Make Havells or Finolex or Plaza , Ceiling Rose three terminal snow white Make Anchor or SSK or CONA , LED Bulk head fitting high pressure die cast aluminum front cover with glass cover with specially design gasket with LED lamp 10 watts as per TS , PVC Flexible wire copper conductor multi stranded 0 pont 0016 by 76 Make havells or Finolex or Plaza , PVC Flexible Conduit pipe 15 mm dia Make Polycab or Supreme or Finolex , PVC Round or Square Block Make Polycab or Supreme or Finolex , Fire extinguisher of 1 kg of dry power type conforming to IS 13849 along with its accessories Make Cease fire or Omex or Alfa Fire , Earthing plate 600 x 600 x 6 mm Galvanised steel suitable for GI strip fittings drilled with 2 nos holes for 6 mm dia near one side , CI Earth Pit Cover of size 300 x 300 x 6 mm with Angle iron frame of size 20x20mm 3 mm thick with MS frame , Funnel fitted with 20 mm diameter GI Pipe 1.5 m Long Pipe Make Jindal or Tata or Kalinga , GI wire 4 mm diameter for earthing , Charcoal , Salt normal , Air terminal single pointed aluminium rod 12mm dia and 300mm long , Testing point terminal block make of Gun metal phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw , Aluminium strips 25x3mm , Galvanised iron strip 32x6mm , Funnel fitted with 20mm dia GI Pipe 1 point 5m long Make Jindalor Tata or Kalinga , Earthing Plate 600x600x6mm GI steel suitable for GI strip fittings drilled with two nos holes for 6 mm dia near one side , CI earth pit cover of size 300x300x6mm with angle iron of size 20x20x3mm thick with MS frame , Insulating PVC block 75x75x30mm with insulating clamp nut and bolt Make Presto or Polycab or Finolex , Study chair of size length 56 Cm, Height 82 Cm and Width 56 Cm Type Lacquered finish with arm seat and back cushion velvet upholstery Make Supreme or equivalent , Study Table of size 4 ft x 2ft Wooden top on round tube structure with three drawers on one side , Steel almirah of size 1855mm with 4 shelves MS sheet doors and and locker 1.00mm thicklock material brass and steel finished and thickness of shelves 0 point 90mm , Mild Steel rack adjustable sheet 1.00mm thick nuts and bolts are in hexagon blck steel overall height 1point 755m depth 0 point 410m and width 0 point 915m , Hand Held Trolley of size 1200 x 900 x 1200 mm of 2 mm thick MS plateform and size of wheel 127 mm with loading capacity minimum 200 kg and overall weight of trolleys 19 Kg

Details: CATEGORY: dia GI Tubing medium grade 1 point 5 Mtr Long Make Jindal or Tata or Kalinga , Service cable PVC insulated aluminium conductor 1100 volt grade Heavy duty served with inner service connection 10 Sqmm 2 core Make Havells or Finolex or Plaza , Ceiling Rose three terminal snow white Make Anchor or SSK or CONA , LED Bulk head fitting high pressure die cast aluminum front cover with glass cover with specially design gasket with LED lamp 10 watts as per TS , PVC Flexible wire copper conductor multi stranded 0 pont 0016 by 76 Make havells or Finolex or Plaza , PVC Flexible Conduit pipe 15 mm dia Make Polycab or Supreme or Finolex , PVC Round or Square Block Make Polycab or Supreme or Finolex , Fire extinguisher of 1 kg of dry power type conforming to IS 13849 along with its accessories Make Cease fire or Omex or Alfa Fire , Earthing plate 600 x 600 x 6 mm Galvanised steel suitable for GI strip fittings drilled with 2 nos holes for 6 mm dia near one side , CI Earth Pit Cover of size 300 x 300 x 6 mm with Angle iron frame of size 20x20mm 3 mm thick with MS frame , Funnel fitted with 20 mm diameter GI Pipe 1.5 m Long Pipe Make Jindal or Tata or Kalinga , GI wire 4 mm diameter for earthing , Charcoal , Salt normal , Air terminal single pointed aluminium rod 12mm dia and 300mm long , Testing point terminal block make of Gun metal phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw , Aluminium strips 25x3mm , Galvanised iron strip 32x6mm , Funnel fitted with 20mm dia GI Pipe 1 point 5m long Make Jindalor Tata or Kalinga , Earthing Plate 600x600x6mm GI steel suitable for GI strip fittings drilled with two nos holes for 6 mm dia near one side , CI earth pit cover of size 300x300x6mm with angle iron of size 20x20x3mm thick with MS frame , Insulating PVC block 75x75x30mm with insulating clamp nut and bolt Make Presto or Polycab or Finolex , Study chair of size length 56 Cm, Height 82 Cm and Width 56 Cm Type Lacquered finish with arm seat and back cushion velvet upholstery Make Supreme or equivalent , Study Table of size 4 ft x 2ft Wooden top on round tube structure with three drawers on one side , Steel almirah of size 1855mm with 4 shelves MS sheet doors and and locker 1.00mm thicklock material brass and steel finished and thickness of shelves 0 point 90mm , Mild Steel rack adjustable sheet 1.00mm thick nuts and bolts are in hexagon blck steel overall height 1point 755m depth 0 point 410m and width 0 point 915m , Hand Held Trolley of size 1200 x 900 x 1200 mm of 2 mm thick MS plateform and size of wheel 127 mm with loading capacity minimum 200 kg and overall weight of trolleys 19 Kg

Details: CATEGORY: TA No 4 1 1 Side Light starboard 112 5 deg Green 80W code 6463133361HL 1 , TA No 4 1 2 Side Light Port 112 5 Red 80W CODE 6463133363HL 2 , TA No 4 1 3 Masthead White Light 360 deg 80 W CODE 6463134261 HL 3 , TA No 4 1 4 Stern White light 135 Deg to Aft 40W CODE 6463132261HL 4 , TA No 4 1 5 All round fixed white light 360 deg 25W CODE 6463131260HL 5 , TA No 4 1 6 All round fixed blue light 360 deg 60W CODE 6463131268HL 6 , TA No 4 1 7 Jack staff light 7 deg Aft blue 25W CODE 6463175222HL 7 , TA No 4 1 8 All round fixed white light 360 deg 80W the morse code CODE 6463131361HL 8 , TA No 4 1 9 All round suspended Green light 360 deg 80W suspended type CODE 6463131862HL-9 , TA No 4 1 10 All round suspended red light 360 deg red 80W Suspended type CODE 6463131863HL 10 , TA No 4 1 11 All round suspended Yellow light 360 deg Yellow 80W suspended type CODE 6463131864HL11 , TA No 4 1 12 All round suspended White light 360 deg 25W suspended type CODE 6463131961HL 12 , TA No 4 1 13 All round suspended Red light 360 deg 80W Suspended type CODE 6463131963HL 13 , TA No 4 1 14 Wake White light 7 t 10 deg to Aft 25W CODE 6463174521HL 14 , TA No 4 1 15 Flagship White light 225 deg to Aft 25W CODE 6463175622HL 15 , TA No 4 1 16 All round fixed Red light 360 deg 80W the morse code CODE 6463131363HL 16 , TA No 4 1 17 Towing Yellow light 135 to Aft 80W CODE 6463132261HL 17 , TA No 4 1 18 Blinker White light 225 to Aft 25 W CODE 6463134561HL 18 , TA No 4 1 19 Blinker Red light 360 to Aft 25 W CODE 6463134563HL 19 , TA No 4 1 20 Junction Box for blinker Light IP 56 or higher refer annexure 3 CODE 6461730088 AX , TA No 4 1 21 25W Incandecent lamp with screw E27 27with incisions C220-25-1H CODE 3466262122 , TA No 4 1 22 40W Incandecent lamp with screw E27 27with incisions C220-40-1H CODE 3466262123 , TA No 4 1 23 60W Incandecent lamp with screw E27 27with incisions C220-60- 1H CODE 3466262124 , TA No 4 1 24 80W Incandecent lamp with screw E27 27with incisions C220-80-2H CODE 3466000001 , TA No 5 12 Drawings and Documentation , Additional items if any not indicated in the above stated scope of supply

Details: CATEGORY: 230V AC 50 Hz 6 Amps 10KA , MCB single pole 230V AC 50 Hz 16 Amps 10KA , MCB distribution boards in sheet metal enclosure 8 ways double door with blanks confirming to IS 8623. , Residual current circuit breaker with over load and short circuit protection DP 32 Amps , Modular switch one way 16 AMP 1 module , Modular socket 6A 2 obliq 3 pin combined 2 module. , Modular socket 16A 2 obliq 3 pin combined 2 module. , White cover plate with frame 3 module. , White cover plate with frame 6 module. , Metal flush box 3 Module , Metal flush box 6 Module , Compact Street Light Luminaire with deep drawn housing complete along with single 36W FR L. , PVC casing caping pipe 25mmx16mm confirming to IS 14927 , PVC casing caping L bend 25mm confirming to IS 371 1979. , PVC casing caping T 25mm for conduit pipe , PVC casing caping elbow 25mm dia , PVC casing caping square box 4 inch x 4 inch , Plastic Body Exhaust fan 250mm sweep with louvers. , Plastic Body Wall Mounting Fan 450mm sweep. , Two tier sleeping bunks as per drawing attached to be provided by vendor , Fire extinguisher of capacity 2 Kgs along with its accessories confirming to IS 13849. Two Nos with each shelter , Heating Device Kerosene Based Heating Device of following specifications will be provided with each shelter. , Waste Bin 120 Ltr Dim 480 X 550Top O.D. , Plastic Chair with Handrest model Dynasty Dim 570 W X 593D x 890H. Colour Dark Brown Make Nilkamal or equalent , Cup Board Model Freedom FMDR 1B Dim 595 W X 354d X 1450 H Dark Brown Make Nilkamal or equalent , Looking Mirror 1200X750X3.5mm thick with plastic decorative frame. Make modiguard Saint Gobin Atul Glass , Drilling machine portable type electrically driven , Aluminum straight edge 50mm square 2mm thick 1800mm long , Wooden Flat Gurmala , Water levelling pipe PVC 100 mtr , Hand rivet gun machine , Tile cutter machine with 6 spare blades each , Tasla Iron 18 inch , Shovel with wooden handle , Brick hammer 1.2Kgs , Cutting plier insulate 6 Inch , Screw driver 12 inch with insulated plastic handle , Adjustable spanner 12 inch , Hacksaw frame with 2 blade , Hand gloves insulated with 2 rubber , Drill bit 6mm dia , Drill bit 8mm dia , Drill bit 10mm dia , Tape measuring metallic 30m , Mason trowel Karchi , Axepicks with wooden handle , Fawda with wooden handle , Crowbar 5 feet long , Rammer with wooden handle of wt 5 Kg , Pipe wrench 12 inch , Pipe wrench 18 inch , Aluminum spirit level 6 inch , Brick Line , Neon tester , Sleve for sieving fine and corse agg 900x150mm made of angle iron frame with stand , Spanner Rings 13x17mm , Spanner Rings 10x11mm , Spanner Rings 14x15mm , Spanner Rings 19x22mm , Spanner Rings 24x26mm , Spanner OJDE 19X22 , Plumbbob 250 Gms , Lightning Conductor will be provided as under and stores are as per Appx E and drg at Appx F

Details: CATEGORY: casing and capping confirming to IS 3419 Part 3 Make- Havells,Finolex,Polycab, Natural white or equivalent , Switch socket combination snow white multipurpose 2 in 1, 15 Amp 230 Volts Make-Havells,Finolex,Polycab, Natural white or equivalent , Switch socket combination snow white 5 Amp 230 Volts Make-Havells,Finolex,Polycab, Natural white or equivalent , Service bracket 40mm dia GI Tubing medium grade 1.5 Mtr Long Make-Havells,Finolex,Polycab, Natural white or equivalent , Service cable PVC insulated aluminium conductor, 1100 volt grade Heavy duty served with inner sheathing of PVC tap Make-Havells,Finolex,Polycab, Natural white or equivalent as per store list attached , Ceiling Rose three terminal snow white Make-Anchor,SSK,CONA , LED Bulk head fitting high pressure die cast aluminum front cover with glass cover with specially design gasket with LED lamp 10 watts rechargeable Make-HAVELLS,BAJAJ,PHILIPS, CROMPTON , PVC Flexible wire copper conductor multi stranded 0.0016 oblique 76 Make-Havells,Finolex,Polycab, Natural white or equivalent , PVC Flexible Conduit pipe 15 mm dia Make-Havells,Finolex,Polycab, Natural white or equivalent , PVC Round oblique Squire Block Make- Havells,Finolex,Polycab, Natural white or equivalent , Fire extinguisher of one kilogram capacity, dry power type conforming to IS-13849 along with its accessories Make- Cease fire,Omex,Alfa Fire , Earthing plate 600 x 600 x 6 mm Galvanised steel suitable for GI strip fittings, drilled with 2 Nos holes for 6 mm dia near one side. , CI earth pit cover of size 300 x 300 x 6 mm with Angle iron of size 20x20mm, 3 mm thick with MS frame. , Funnel fitted with 20 mm diameter GI Pipe 1.5 m Long. Pipe Make-Jindal,Tata,Kalinga , GI wire 4 mm diameter For earthing , Charcoal , Salt normal , Cement OPC 43 Grade packed in HDPE bag each 50 Kg wt conforming to IS 8112-1989 Make-Birla Gold,Ambuja,Ultratech,ACC,JK,Dalmia , Coarse Sand free from vegetation Qty-0.20 Cum , Coarse aggregate 20mm graded Qty-0.20 Cum , Coarse aggregate 40mm graded Qty- 0.20 Cum , Air termination single pointed aluminium rod 12 mm dia and 300 mm long. , Testing point terminal block make of gun metal and phosphorus bronze size 75 x 75 x 25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screw , Aluminium strips 25 x 3.0 mm , Galvanised Iron strip 32 x 6 mm , Insulating PVC block 75x75x30 mm with insulating clamp nut and bolt Make- Presto,Polycab,Finolex , Study chair of size length 56 Cm, Height 82 Cm and Width 56 Cm, Type Lacquered finish with arm, seat and back cushion, velvet upholstery Make- Supreme or equivalent , Study Table of size 4 feet X 2 feet, Wooden top on round tube structure with three drawers on one side. , Steel almirah of size 1855mm with 4 shelves. MS sheet doors and and locker 1.00mm thick, lock material brass and steel finished and thickness of shelves 0.90mm , Mild Steel rack adjustable ,sheet 1.00mm thick, nuts and bolts are in hexagon blck steel, overall height 1.755m depth 0.410m and width 0.915m , Hand Held Trolley of size 1200 x 900 x 1200 mm of 2 mm thick MS plateform and size of wheel 127 mm with loading capacity minimum 200 kg and overall weight of trolleys 19 Kg.

Details: CATEGORY: Polycab, Natural white or equivalent , Switch socket combination snow white multipurpose 2 in 1, 15 Amp 230 Volts Make - Anchor, SSK, CONA. , Switch socket combination snow white 5 Amp 230 Volts Make - Anchor, SSK, CONA , Service bracket 40mm dia GI Tubing medium grade 1.5 Mtr Long Make Havells, Finolex, Polycab, Natural white or equivalent . , Service cable PVC insulated aluminium conductor, 1100 volt grade Heavy duty served with inner sheathing of PVC tap and overall PVC sheathed in service as per store list attached , Ceiling Rose three terminal snow white Make - Anchor, SSK, CONA , LED Bulk head fitting high pressure die cast aluminum front cover with glass cover with specially design gasket with LED lamp 10 watts Make - HAVELLS, BAJAJ, PHILIPS, CROMPTON , PVC Flexible wire copper conductor multi stranded 0.0016 by 76 Make - Havells, Finolex, Polycab, Natural white or equivalent , PVC Flexible Conduit pipe 15 mm dia Make - Havells, Finolex, Polycab, Natural white or equivalent , PVC Round oblique Square Block Make - Havells, Finolex, Polycab, Natural white or equivalent , Fire extinguisher of 1 kg of dry power type conforming to IS-13849 along with its accessories Make - Cease fire, Omex, Alfa Fire , Earthing plate 600 x 600 x 6 mm Galvanised steel suitable for GI strip fittings, drilled with 2 nos holes for 6 mm dia near one side. , CI Earth Pit Cover of size 300 x 300 x 6 mm with Angle iron frame of size 20x20mm, 3 mm thick with MS frame. , Funnel fitted with 20 mm diameter GI Pipe 1.5 m Long. Pipe Make-Jindal, Tata, Kalinga , GI wire 4 mm diameter for earthing. , Charcoal , Salt normal , Air terminal single pointed aluminium rod 12mm dia and 300mm long. , Testing point terminal block make of Gun metal and hosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw. , Aluminium strips 25x3mm. , Galvanised iron strip 32x6mm. , Funnel fitted with 20mm dia GI Pipe 1.5m long Make - Jindal, Tata, Kalinga , Earthing Plate 600x600x6mm GI steel suitable for GI strip fittings, drilled with two nos holes for 6 mm dia near one side. , CI earth pit cover of size 300x300x6mm with angle iron of size 20x20x3mm thick with MS frame. , Insulating PVC block 75x75x30mm with insulating clamp nut and bolt Make-Presto, Polycab, Finolex , Study chair of size length 56 Cm, Height 82 Cm and Width 56 Cm, Type - Lacquered finish with arm, seat and back cushion, velvet upholstery Make - Supreme or equivalent , Study Table of size 4 feet X feet, Wooden top on round tube structure with three drawers on one side. , Steel almirah of size 1855mm with 4 shelves. MS sheet doors and and locker 1.00mm thick, lock material brass and steel finished and thickness of shelves 0.90mm , Mild Steel rack adjustable ,sheet 1.00mm thick, nuts and bolts are in hexagon blck steel, overall height 1.755m depth 0.410m and width 0.915m , Hand Held Trolley of size 1200 x 900 x 1200 mm of 2 mm thick MS plateform and size of wheel 127 mm with loading capacity minimum 200 kg and overall weight of trolleys 19 Kg.