Drawer Tenders

Details: i) Geo-Technical & Hydro- geological Sub Surface Investigation, Surveying, Planning, Designing, Construction & commissioning of atleast. 5.0 meter dia. & required depth Radial Collector well with 250 mm dia & 300 mtr.(approx) long Infiltration Gallery with laying of LCG strainer pipe of minimum 8 mm thick including sub surface dyke to harvest 4.24 MLD raw water with 16 hours designing operation along with Pump House, Access & Pipe carrying Bridge at Subarnarekha along with 01(one) LT Station room for termination of WBSEDCL power source at vicinity of High Bank at Subarnarekha River (Kerwari), protection work at river bank, including construction of Pipe carrying Bridge with necessary Civil, Electrical (according to I.E. rules), Mechanical & all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement and (ii)Laying of raw water rising main from intake well to CWR(D.I./K9 Pipes All types and Class) with all necessary fittings & valves for raw water rising main work, temporary road restoration works for vehicular movement and pillar carrying pipe line and Jack Pushing works for raw and clear water rising main work all complete and (iii)Construction of R.C.C Over Head Reservoirs(OHR) of 1000 cum & 600 cum capacity with 20 m Staging height per approved departmental design, drawing & Specification etc at zone – A & Zone – B including land development , approach road, internal drainage, boundary wall and Sal Bullah Piling etc and pipe line work and connection to the Distribution and inlet line all complete (iv) Surveying , Geo-Technical Investigation, Planning, Designing, Construction & Commissioning of 770 Cum. capacity Clear Water Reservoir with Pumping station, with Construction of weir with minimum 400 cum capacity sedimentation tank and Slow sand filter of area 1000 Sqm minimum, Chlorination treatment unit, ,land development ,approach road, internal drainage, and boundary wall including Electro- Mechanical works at Jhalda and all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement within Jhalda Municipality under AMRUT 2.0 Project.

Details: i) Geo-Technical & Hydro- geological Sub Surface Investigation, Surveying, Planning, Designing, Construction & commissioning of atleast. 6.0 meter dia. & required depth Radial Collector well with 250 mm dia & 300 mtr.(approx) long Infiltration Gallery with laying of LCG strainer pipe of minimum 8 mm thick including sub surface dyke to harvest 4.24 MLD raw water with 16 hours designing operation along with Pump House, Access & Pipe carrying Bridge at Subarnarekha along with 01(one) LT Station room for termination of WBSEDCL power source at vicinity of High Bank at Subarnarekha River (Kerwari), protection work at river bank, including construction of Pipe carrying Bridge with necessary Civil, Electrical (according to I.E. rules), Mechanical & all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement and (ii)Laying of raw water rising main from intake well to CWR(D.I./K9 Pipes All types and Class) with all necessary fittings & valves for raw water rising main work, temporary road restoration works for vehicular movement and pillar carrying pipe line and Jack Pushing works for raw and clear water rising main work all complete and (iii)Construction of R.C.C Over Head Reservoirs(OHR) of 1000 cum & 600 cum capacity with 20 m Staging height per approved departmental design, drawing & Specification etc at zone – A & Zone – B including land development , approach road, internal drainage, boundary wall and Sal Bullah Piling etc and pipe line work and connection to the Distribution and inlet line all complete (iv) Surveying , Geo-Technical Investigation, Planning, Designing, Construction & Commissioning of 770 Cum. capacity Clear Water Reservoir with Pumping station, with Construction of weir, sedimentation tank and Slow sand filter , Chlorination system ,land development ,approach road, internal drainage, and boundary wall including Electro- Mechanical works at Jhalda and all other allied works all complete. After satisfactory completion and commissioning, 3 (three) months trial run, necessary training of maintenance staff & thereafter (subsequently) 5 (five) years operation and maintenance with security /guarding arrangement within Jhalda Municipality under AMRUT 2.0 Project.

Details: SET OF SEATS FOR L.H.B GS AMRIT BHARAT COACHES. FOLLOW CUSHIONING MATERIAL EITHER PU FOAM TO RDSO SPEC. RDSO/2007/CG-04 REV. 01 OR SILICON FOAM TO RDSO SPEC.RSDO/ 2013/CG-13 REV. 01 WITH FIRE PROPERTIES COMPLIANT TO R21 HL-3 OF EN45545 STANDARD AND U PHOLSTERY TO RDSO SPEC.RDSO/2008/CG-07 REV-NIL WITH AMENDMENT SLIP NO-5 WITH CORRIGEN DUM 1 OF MAY 2015. COLOUR SHADE TO BE FOLLOWED AS PER DESIGN LNO.MD46271 DATED 30.09. 24, as per Drawing: MPLSLSDD VERSION 1, Packing Instruction: ALL PROTRUDING PORTIONS OF SEAT/ BERTH SHOULD BE PROTECTED WITH ENVIRONMENT FRIENDLY PRE MOULDED THERMOCOL CAP OF R EQUISITE STRENGTH OR SILICON RUBBER CAP AS AN ALTERNATE OPTION. EACH INDIVIDUAL SEAT/BE RTH SHOULD BE COVERED WITH BIODEGRADABLE BUBBLE SHEET OF DIAMETER 10MM AND THICKNES S 30 MICRON ALL ROUND. FLAP OF BERTH SHOULD BE OUTSIDE THE BUBBLE SHEET PACKING LEAVIN G SEAT & BERTH MOUNTING UNCOVERED. THEN IT SHOULD BE WRAPPED ALL ROUND IN THICK LAMIN ATED JUTE FABRIC OF SUFFICIENT STRENGTH. THE ASSEMBLY SHOULD BE TIED WITH NYLON STRIPS. I T IS FURTHER WRAPPED WITH BIODEGRADABLE POLYTHENE ALL ROUND TO PREVENT INGRESS OF DU ST/WATER. FOR THE FOLLOWING ITEMS (IF COVERED UNDER S&B SET) THE ITEM-WISE PI (LATEST VER .) WILL BE AS UNDER : 1. CHAIR ANGLES, EXPANDED METAL PARTITION FRAME,SUSPENSION STRAPS, SUPPORTS AND MTG. BKT PI004 2. HARDWARE ITEMS PI019 3. ITEMS LIKE BEARING BKT, CHAIN BKT, C ATCH ARGGT, HINGE BKT AND SLEEVES ETC. PI020 4. LADDERS PI031, LUGGAGE RACKS PI042 A LIST SHOULD BE PASTED ON EACH BOX SHOWING PO NO, PL NO, DESCRIPTION, DRG NO, QTY, FIRM NAME & ADDRESS, DATE OF DISPATCH ETC NOTE : FIRMS HAVE OPTION TO PROVIDE QR CODE . THE ITEM S HELL CARRY A QR CODE ON CARDBOARD BOX NEAR THE MANUFACTURER NAME STICKER CONTAININ G THE DETAILS AS LISTED BELOW: " NAME OF THE MANUFACTURER " PURCHASE ORD ER NUMBER " PURCHASE ORDER DATE " UNIQUE SERIAL NUMBER (OR LOT NUMBE R FOR BULK ITEMS) OF THE MANUFACTURER OR " DATE OF MANUFACTUR E " DELIVERY CHALLAN NO. " DELIVERY CHALLAN DATE THE QR CODE SHALL BE AS PER ISO/IEC18004 MODEL2 AND THE DATA SHALL BE AVAILABLE AS XM L USING THE TAGS DETAILED ABOVE

Details: Supply Of One Rake Set Of Seats Without Seat Fixing Profile For Trainset -18 As Per Specification Icf/md/spec-367 Rev-02 For Mc,tc,dtc,dtc2,ndtc Coaches & Icf/md/spe C-366 Rev-03 For Ndtc/ec & Ndtc/ec2 Coaches., As Per Drawing: Mplseatsts18 Version 6, Pack Ing Instruction: Chair Car Seat( Ac & Nac ) : I. All Protruding Portions Of The Chair Car Seat Should Be Protected With Plastic Cover. 2.then Complete Seat And Its Corners / Hand Re St/ Foot Rest Should Be Properly Wrapped With Biodegradable Air Bubble Sheet Of Thick Ness 30 Micron And Bubble Diameter 10mm. 3. The Full Seat Should Be Further Wrapped W Ith 3 Ply Corrugated Paper Sheet. 4. Each Individual Chair Should Be Covered All Aroun D With Transparent, Plain, Biodegradable, Polythene Sheet To Prevent Ingress Of Dust/ Water. 5. The Seat Bottom Frame Portion Should Be Fitted With M.s Supports For Its Bala Ncing, So That The Chair Can Rest On The Floor Without Tilting On Any Side. 6. The Overa Ll Packing Should Be Such That It Is Not Damaged During Transportation Of The Materia L, The Seats Should Be Tied Up In Pairs Only. 7. All Hardware/accessories/loose Items In O Ne Coach Set Should Be Separately Packed In Wooden Box Having Sufficient Strength. 8. A List Should Be Pasted On Each Box Showing Purchase Order No., Pl No., Description Of I Tem, Drg. No., Quantity, Firm Name, Address & Date Of Dispatch And Its Contents. Note : Q R Code Is To Be Affixed " Near Manufacturer Name Plate On Each Seat " On Top Of Packed Seat As Per Pi Mentioned Above " On Top Of Wooden Box For Sr.no.7 Qr Code Having Detai Ls As Listed Below : 1 Name Of The Manufacturer 2 Purchase Order Number 3 Purchase Order Date 4 Unique Serial Number (or Lot Number For Bulk I Tems) Of The Manufacturer Or 5 Date Of Manufacture 6 Delivery Challan No. 7 Delivery Challan Date The Qr C Ode Shall Be As Per Iso/iec18004 Model2 And The Data Shall Be Available As Xml Using Th E Tags Detailed Above. Incase The Above Details Are Not Available, Or The Qr Codes Are Not Readable, The Supplied Material Is Liable To Be Rejected. [ Warranty Period: 84 Months After The Date Of Delivery ]

Details: Oh Kit Of Split Pins For Am12/pan-01/ir01 Type Pantograph. One Kit Consisting Of 08 Items Of 16 Nos.as Under:- [1]split Pin For Mechanism Assly.item No.20.8 To M/s.sil New Ref.no.s0072010440 Or Gsec Drg.no.gsec/panto/sp.05 Or Similar To M/s Contransys Make Size 4x40 Mm -02 Nos. [2]split Pin For Steedy Link Assly.item No.17.5 To M/s Sil New Ref.no.s0072010120 Or Gsec Drg.no.gsec/panto/sp.01 Or Similar To M/s Contransys Make 1.6x20 Mm -01 No. [3]split Pin For Push Rod Assly.item No.8.6 To M/s Sil New Ref.no. S0072010100 Or Gsec Drg.no.gsec/panto/sp.01 Or Similar To M/s Contransys Make Size 1.6x20 Mm -01 No. (4) Split Pin For Push Rod Assly.item No.109 To M/s Sil New Ref.no. S007210336 Or Gsec Drg.no.gsec/panto/sp.04 Or Similar To M/s Contransys Make Size 3x35 Mm-01 No. (5) Split Pin For Support Rod Cylinder Assly.(plunger)item No.16.16 To M/s Sil New Ref.no.s0070210332 Or Gsec Drg.no.gsec/panto/sp.04 Or Similar To M/s Contransys Make Size 3x25 Mm -02 No. (6) Split Pin For Support Rod Cylinder Assly.(plunger)item No.16.17 To M/s Sil New Ref.no. S0072010440 Or Gsec Drg.no.gsec/panto/sp.05 Or Similar To M/s Contransys Make Size 4x40 Mm -02 No. (7) Split Pin For Yoke Assly. Item No.7.2.9 To M/s Sil New Ref.no. S0072010225 Or Gsec Drg.no.gsec/panto/sp.02 Or Similar To M/s Contransys Make Size 2x25 Mm -06 Nos. (8) Split Pin For Central Pedestal Assly. Item No.6.17 To M/s Sil New Ref.no. S0072010336 Or Gsec Drg.no.gsec/panto/sp.04 Or Similar To M/s Contransys Make Size 3x35 Mm -01 No. As Per Drg.no. Drawing No. Is Mentioned In Item Description.

Details: CATEGORY: Trainee Station _Personal Computer with given minimum specifications or higher_ Consisting of following items_Processor , Instructor Station _Configured as Server PC with given minimum specification or higher_Processor_ IntelCore TM i5_1334u Processor , Ethernet Switch 16 port , Customised Gas Ionization Detector_3 _GID_3_ with sub assembly_As per Drawing_ specification and design held with 515 ABW_ , Customised Portable Dosage Meter _PDM_ with sub assembly _As per Drawing_ specification and design held with 515 ABW , Customised Portable Dosage Rate Meter _PDRM_ with sub assembly _As per Drawing_ specification and design held , Customised Comn Bridge with sub assembly_As per Drawing_ specification and design held with 515 ABW Main Controller Board Qty_01 , Customised Battery Charger Unit with sub assembly _Electronic items__As per Drawing_ specification and design held , Customised Mechanical Hardware requirementsGas Ionization Detector_3 _GID_3_ Enclosure_As per Drawing , Customised Mechanical Hardware requirements Portable Dosage Meter _PDM_ Enclosure , Customised Mechanical Hardware requirements Portable Dosage Rate Meter _PDRM_ Enclosure , Customised Mechanical Hardware requirements Communication BridgeABS Enclosure Mockup , Customised Mechanical Hardware requirements Battery Charger Unit , Misc 6mm aluminium spacers Qty 50 , UTP CAT Bundle _50 m_ As per sample available with 515 ABW , RJ 45 connector , Spike Busters 5_15 A _ 05 sockets_ input plug 5AMP_ , Serial Cable PDM to Radio Set , Serial Cable PDRM to Radio Set , Serial Cable GID_ 3 to Radio Set , Serial Cable Communication Bridge to Radio Set , UPS_1KVA _APC_ with min 60 min backup and 03core i_p o_p power cable , Adhesive Feviqwick 10ml tube , Allen key _2_3_4_5_6_7_8_9 Set of 8_ , Bubble sheet _m_ , Corrugated sheet _m_ , Insulation tape _roll_ , Marker Pen Black _ Red , Nose plier , Packing tape _roll_ , Steel Box _As per sample available at 515ABW_ 40x18x18 with lock and key , Screw driver Set , Spanner open_jaw 16_17 , Spanner open_jaw 14_15 , Spanner open_jaw 7_9 , Crimping Tool RJ 45 , Technical manual , User hand book , Log Book , DVD Recordable DVD 4_7 GB with jewel case , DVD Recordable DVD 8_5 GB with jewel case

Details: Design Manufacture And Supply Of High Tensile Aar H Type Tight Lock Centre Buffer Coupler Head With Transition Screw Coupling And Its Associated Components For Fitment On Broad Gauge Passenger Coaches Of Indian Railways As Per Rdso.specn.no. Rds O/2009/cg-22, Rev -01 One Coupler Set Shall Consists Of The Following 1.tight Lock Coupl Er Head With Transition Screw Coupling And Its Associated Components 1 No Rdso Approved Firm Drgs. 2.balanced Draft Gear With Pivot Pin 1 No Rdso Approved Firm Drgs. 3.supporting Device For Coupler Head With M20 Fasteners 1 No Rdso Approved Firm Drgs. 4.manual Uncoupling Device With M12 Fasteners 1 No Rdso Approved Firm Drgs. 5.rear Carrier Plate For Draft Gear With M16 Fasteners 1 No Rdso Approved Firm Drgs. 6.front Carrier Plate For Draft Gear With M16 Fasteners 1 No Rdso Approved Firm Drgs. Special Co Ndition : 1. Maintenance Manual In Soft Copy And Hard Copy Shall Be Supplied With Item. 2.n Ecessary Test Certificates As Per Rdso.specn.no. Rdso/2009/cg-22 (rev -01) Shall Be Suppli Ed With Item. 3. Amd-01 Of Rev.03 Or Latest Revision Of Specification Rdso/2011/cg-03 Refer Red In Rdso/2009/cg-22, Rev -01 Or Latest Shall Be Followed. 4. Tenderer To Submit Rdso App Roved Drawings At The Time Of Quoting The Tender. 5. Packing Condition: Items Are To Be Packed In Two Different Boxes As Given Below. I. List Of Items To Be In Box-1 1. Balanced D Raft Gear With Wedge Block Assembly & Wedge Block. 2. Rear Carrier Plate 3. Fornt Carri Er Plate 4. Fasteners For Front And Rear Carrier Plates. Ii. List Of Items To Be In Box-2 1. C Oupler Head And Associated Components. 2. Main Pivot Pin. 3. Supporting Device For Coupl Er Head. 4. Fasteners For Supporting Device. 5. Manual Coupling Device 6. Fasteners For M Anual Uncoupling Device. 7. Split Pins For Carrier Plate. 8. Balance Items, If Any.. Instructions For Packing Of Fasteners. 1. Box-1: Item-4 2. Box-2, Item-4,6 & 7/ Each To Be Pa Cked And Sealed Separately In Transparent Polythene Cover Of Minimum 200 Microns With Appropriate Description Labels Kept Inside For Easy Identification. [safety Item] [ Warrant Y Period: 84 Months After The Date Of Delivery ] [quantity Tolerance (+/-): 5 %age , Item Category : Normal , Total Po Value Variation Permitted: Max 8 Lacs ] ]

Details: :seats For Lhb Non Ac Chair Car Coaches (108 Seater). Follow Cushioning Ma Terial Either Pu Foam To Rdso Spec. Rdso/2007/cg-04 Rev. 01 Or Silicon Foam To Rdso Spec . Rdso/2013/cg-13 Rev. 01 With Fire Properties Compliant To R21 Hl-3 Of En45545 Standard And Upholstery To Rdso Spec. Rdso/2008/cg-07 Rev-nil With Amendment Slip No-5 And Cor Rigendum 1 Of May 2015, As Per Drawing: Mdts-219 Rev.03 With Corrigendum No.1 Issued Vid E Letter No Md35131 Dt.31/01/22, Packing Instruction: Chair Car Seat( Ac & Nac ) : I. All Protr Uding Portions Of The Chair Car Seat Should Be Protected With Plastic Cover. 2.then Co Mplete Seat And Its Corners / Hand Rest/ Foot Rest Should Be Properly Wrapped With Bio Degradable Air Bubble Sheet Of Thickness 30 Micron And Bubble Diameter 10mm. 3. The Fu Ll Seat Should Be Further Wrapped With 3 Ply Corrugated Paper Sheet. 4. Each Individual Chair Should Be Covered All Around With Transparent, Plain, Biodegradable, Polythene Sheet To Prevent Ingress Of Dust/water. 5. The Seat Bottom Frame Portion Sh Ould Be Fitted With M.s Supports For Its Balancing, So That The Chair Can Rest On The Fl Oor Without Tilting On Any Side. 6. The Overall Packing Should Be Such That It Is Not Da Maged During Transportation Of The Material, The Seats Should Be Tied Up In Pairs Only. 7. All Hardware/accessories/loose Items In One Coach Set Should Be Separately Packed I N Wooden Box Having Sufficient Strength. 8. A List Should Be Pasted On Each Box Showi Ng Purchase Order No., Pl No., Description Of Item, Drg. No., Quantity, Firm Name, Addres S & Date Of Dispatch And Its Contents. Note : Qr Code Is To Be Affixed " Near Manufactur Er Name Plate On Each Seat " On Top Of Packed Seat As Per Pi Mentioned Above " On Top O F Wooden Box For Sr.no.7 Qr Code Having Details As Listed Below : 1 Name Of The Manufa Cturer 2 Purchase Order Number 3 Purchase Order Date 4 Unique Serial Number (or Lot Number For Bulk Items) Of The Manufacturer O R 5 Date Of Manufacture 6 Delivery Challan No. 7 Delivery Challan Date The Qr Code Shall Be As Per Iso/iec18004 Model2 And The Data Shall Be Available As Xml Using The Tags Detailed Above. Incase The Above Deta Ils Are Not Available, Or The Qr Codes Are Not Readable, The Supplied Material Is Liable To Be Rejected. [ Warranty Period: 84 Months After The Date Of Delivery ] ]

Details: Set Of Gauges For Schaku Coupler With Calibration Certificate (traceable To Nabl Certified Lab) & Traceability Certificate As Per List Below- 1) Profile Gauge For Upper & Lower Cup Sleeve (2ed-181-1149(schaku 40.586.06.01 (4) & 2ed-18101153(schaku(40.624.06-4(3),drg No.-se-g-121, Qty-02 Nos. 2) Gauge For Pin(31.8c11),drg. No.-se-g-120,qty-02 Nos. 3) Gauge For Allen Bolt/screw (2ed-181-1166),drg.no.-se-g-128, Qty-02nos. 4) Gauge For Fork Head 2ed-181-1204(schakudrgno.40-1000.10-6(3),drg. No.- Se-g-132, Qty-02 Nos.5) Gauge For Front Plate Sub Assy.2ed-181-1156 (schaku Drg.40.586.06.02 (4), Drg.no.-se-g-122,qty-02 Nos.6) Profile Gauge For Adjustable Cup Sleeve/pair Of Cup Sleeve 2ed-181-1074(schaku Drg.40.317.13-1 (3), Drg. No.se-g-129, Qty -02 Nos. 7) Gauge For Bush Upper & Lower 2ed-181-1091(schaku Drg.40-524.07-3(4) &2ed -181 - 1089(schaku Drg.40-524.-7-4(4), Drg.no.-se-g-118, Qty-02 Nos. 8) Limit Gauge For Yoke (sub.assy.)2ed-181-1183(schaku Gr.40.586.06.04(2), Drg. No.-se-g-124, Qty -02 Nos. 9) Snap Gauge For Bolt 2ed-181-1181(schaku Drg.40.586.06.3 (4), Drg.no.se- G-126.qty-02nos. 10) Snap Gauge For Bearing Bolt 2ed-181-1093(schaku Drg.40.586.07.03 (3), Drg. No.se-g-119, Qty-02 Nos. 11) Limit Gauge For Carrier(sub Assy.)& Leaf Spring Compl.subassy.2ed-181-1200 (schaku Drg.40-524.07.03(4) & 2ed-181-1106(schaku Drg.40.524.07.08 (20),drg.no.-se-g-117, Qty-02 Nos.12) Limit Gauge For Rear Plate Sub Assembly 2ed-181-1157(schaku Drg.40.586 .06.03 (4) Drg.no.se-g-123, Qty-02 Nos. 13) Gauge For Articulation Bearing 2ed-181-1151(schaku Drg.40.sk.1960 (3) Drg.no.s-g-127, Qty -02 Nos.14) Go Gauge For Draft Gear/draw &buff Gear (sub Assy.) Drg.no.se-g-136, Qty-02 Nos.

Details: CATEGORY: 80CH Embedded Network Video Recorder , 5MP Dome Camera , 5MP Bullet Camera , 2MP Dome Camera , 2MP PTZ Dome Camera , HDD 6 TB SATA Interfaces , Category 6 Unshielded 4 Pair Cable , Category 6 UTP Patch Panel 24 Port Fully Loaded , Category 6 UTP Patch Cord , 12 Core OFC Singlemode Armored Outdoor Cable , 24 Port LIU Rack Mount with Fully Loaded , LC LC Singlemode Duplex Patch Cord , Core Switch 24 Port , Access Switch 24 Port , 10G Uplink SFP Module , Video Encoder , Media Converter , BNC Patch Cord , 55 Inch Display , 43 Inch Display , Client Workstation , 12U Rack Wall Mount with Power Manager and Fan , 42U Rack 19 inch Network Rack , PVC Capping Casing 2 inch cross 2 inch , PVC Capping Casing 1 inch cross 1.25 inch , 1 inch PVC Pipe , 1 inch PVC Bend , 3 by 4 inch PVC Bend , Clamp for PVC fixing , Flexible Hose Stainless Steel , Outdoor Junction Box for fixing Cameras , RJ45 Connectors , 6KVA UPS , 3 Core 2.5 Sq mm Power Cable , 3 Core 4 Sq mm Power Cable , Electrical Junction Box , 12 way DB , 6mm Screw, 6mm fisher, Insulation tape, Cable tie , Installation and configuration 80 CH Embedded Network Video Recorder , Configuration and Fixing of 5MP Dome Camera , Configuration and fixing of 5MP Bullet Camera , Configuration and Fixing of 2MP Dome Camera , Configuration and Fixing of 2MP PTZ Camera , Installation and RAID Configuration Surveillance HDD , Laying of UTP CAT 6 cable , Termination and Fixing Cat6 24 Port Patch Panel , Termination and Fixing Cat6 Information Outlet , Laying of 12 Core OFC , Fixing and Splicing 24 Port LC Type LIU Single mode , Configuration of Core Switch , Configuration of Access Switch , Fixing of 55 inch Display UHD , Fixing of 43 inch Display UHD , ITC for Client Workstation , Fixing of 12U Rack Wall Mount , Fixing of 42U Rack 19 inch Network Rack , Laying of PVC Capping Casing 2 inch , Laying of PVC Capping Casing 1 inch , Fixing of PVC Outdoor Junction Box , Termination of RJ45 Connector , Installation of 6 KVA UPS , Laying of 3 Core 2.5 SQ MM Power Cable , Laying of 3 Core 4 SQ MM Power Cable , Fixing of Electrical Junction Box , ITC of 12 way DB , Installation Testing Commissioning with Documentation and Drawing