School Of Planning And Architecture Tender

with earth/soil brought from outside

Providing. mixing. laying. consolidating and curing in position plain cement concrete (without fly ash) excluding the cost of centering and shuttering with necessary slopes as specified for foundations, grade slabs, ramps, sills, copings, trenches, filling to space, etc. for any thickness and all depths and heights using graded coarse aggregates from 40 mm to 10 mm complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

in 1:4:8 pcc under floors (screeding)

in 1:4:8 pcc under foundations

Providing, mixing, laying. vibrating, curing and roughening to surfaces wherever required, dewatering wherever required, 1:1:2 (1 cement: 1 coarse sand (zone-II) derived from natural sources 2 graded stone aggregate) reinforced cement concrete equivalent to batching plant mixed reinforced cement concrete of Design mix M25 grade excluding the cost of centering shuttering and reinforcement but including all required super plasticizer & retarders etc. and with minimum cement content as per all relevant & applicable IS codes) to required levels and shape at all heights and depths using 20 mm max to 6 mm size well graded aggregates as per drawing and specifications. The rate shall also include provision of shrinkage strips, Construction L joints, Contraction joints, Control joints and shear keys as per structural drawings complete in all respect as per specifications, drawings and as directed by Engineer-in-charge

in walls (any thickness) including pilasters, buttresses, shear walls, retaining walls in suspended slabs, balconies, chajjas, canopies, in lintels, floor slabs & beams, curved beams, lintel beams, gutter beams, trenches, sumps, manholes, staircases, landing of stairs, steps

in louvers, fins, facias, pardis, coping etc. In foundations, footings, foundation beams, piers, pedestals, plinth beams etc. stitching slabs, rafts,

Providing. erecting and fixing adequate and good quality, leak proof, formwork/shuttering upto a floor height of 4.5 meter for suspended roofs. beams, soffits, balconies, columns, shear walls, retaining walls, foundations, footings, foundation beams. staircases, over head water tanks etc. including centering. strutting. propping. bracing, bolting. welding and staging etc. complete & keeping the same to the lines and levels to required shape, size at all depths and heights as per drawing and specifications and removing the same after specified period complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

Foundations. footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.Suspended floors, roofs, landings, balconies and access platform

Providing and placing in position thermo mechanically treated steel reinforcement in RCC works (including cost of binding wire & concrete cover blocks) as per drawings and specifications, at all heights and depths including carting, cleaning, straightening, cutting, stacking, bending. placing and tying, etc., (binding the reinforcement with 18mm gauge annealed wire etc. for all sizes of bars at each junction) including all astatage/cut pieces, complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

Thermo Mechanically Treated Bars of Fe-500

Providing and applying two or more coats of class I synthectic enamel paint on steel surface like doors,windows,frames and trusses etc. of approved make and shade. Including coat of primer …as per direction of engineer in chagre

The Items mentioned below must incorporate the following items : Glass should be plain. All fasteners should be of stainless steel.Water test for leakage at joints to be carried out. All joints should be sealed with silicone of the approved make. All Hardware shall be of good quality.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of make conforming to approved IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Inclusive of Paneling, dash fasteners, fittings, etc): For Fixed Portion Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade ACIS AC 15

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber neoprene gasket required (inclusive of Fittings etc.)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Inclusive of aluminium snap beading):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Demolition cement concrete manually/by mechanical means including disposal of the same within 50 meters lead complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

Nominal mix 1:3:6 or richer mix (including equivalent concrete design mix)

Demolishing reinforced cement concrete (RCC) in all mixes, in foundations, sub-structure and super structure, at all heights/depths, including disposal of unserviceable materials within 50 meters complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposable of unserviceable material within 50 meters lead complete in all respect as per specifications, drawings and as directed by Engineer-in-charge. In Cement Mortar

Demolishing stone rubble masonry work manually/by mechanical means including stacking of serviceable material and disposable of unserviceable material within 50 meters lead complete in all respect as per specifications, drawings and as |directed by Engineer-in-charge. In Cement Mortar

Dismantling doors, windovws and fixed panels (anodized aluminium, steel) including chowkhats. shutters, glass. architrave, holdfasts, hinges etc. complete and stacking within 50 meters lead complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

Of area 3.0 Sq. Meter and below

Of area beyond 3.0 Sq. Meter

Supplying, transporting, fabricating, erecting, structural steel (Fe 250) frame work at all levels including cutting, welding, seal welding, bolting, threading, wherever necessary and generally as per the enclosed specifications and drawings for framed work. louvers, brackets, sag rods, built up sections, and painting with two coats of red oxide zinc chromate primer, (total D.F.T. 50 microns) as per specification including surface preparation with mechanical wire brushing and hand cleaning etc. Item includes all necessary materials/fixing/finishing etc. complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.

Providing and fixing High Grade Aluminium coating profile sheet (0.6 mm thick) of JSW make or equivalent ribbed profile all floors including making necessary holes screws and other fixture as required complete in all respect at all floors. (Rate shall include scaffolding which shall be provided by the contractor with all the safety of the workers employed and nothing extra shall be paid on this account). Item includes all necessary materials/fixing/finishing etc. complete in all respect as per specifications, drawings and as directed by Engineer-in-charge.