Public Works Department Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 7,54,214Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_PWD_220566_1Bid Award Id
ViewTender No
01 /EE/CBMD M-121(N)/2022-23Tender Authority
Public Works Department ViewPurchaser Address
-Website
http://https://www.pwddelhi.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil.
48
-
51.75
Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. All kinds of soil
1200
-
13.95
Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. All kinds of soil
24
-
52.65
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
30
-
5481.95
1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
185
-
4209.05
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)
60
-
6215.35
Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform
66
-
422.3
Lintels, beams, plinth beams, girders, bressumers and cantilevers
162
-
342.9
Edges of slabs and breaks in floors and walls Under 20 cm wide
102
-
122.2
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars
6000
-
56.6
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
227
-
4751.65
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)
18
-
593.5
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
276
-
2937.7
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
70
-
2488.95
Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm
48
-
74.15
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete
6
-
85.85
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.
60
-
438.75
Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30 mm thick pre laminated PVC door shutters
24
-
3232.7
Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading.
6
-
1094.1
Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multichambered frame, sash and mullion (where ever required)extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket,stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holesfor fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glasspanes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus5% tolerance in dimension i.e. in depth & width of profile shallbe acceptable. Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series)frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto0.75 sqm.)
6
-
7908.15
Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension.(Area of window upto 2.50 sqm).
36
-
5822.6
Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.
5850
-
78.45
Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm
96
-
89.7
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
1595
-
67.6
Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes
12690
-
93.9
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
9240
-
85.95
Providing and fixing stainless steel ( Grade 304) railing/gate made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, hinges etc.).
5193
-
472.4
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Dark shade pigment using ordinary cement
108
-
716.35
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.
54
-
822.45
Providing and laying double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
721
-
1119.4
Providing and fixing plain Multipurpose Cement board ( High Pressure steam cured ) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete (frame work to be paid separately) : 6 mm thick cement board as per IS: 14862
1700
-
516.1
12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
400
-
168.25
15 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand)
400
-
194.6
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).
1200
-
96.05
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
800
-
78.4
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
70
-
997.05
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar
12
-
842.75
Demolishing mud phaska in terracing and disposal of material within 50 metres lead.
77
-
373.95
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
200
-
120.55
Supplying and stacking at site. Good earth.
120
-
332.55
Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made bytable vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, allcomplete as per manufacturer's specifications & direction of Engineer in-Charge. 60mm thick Cement concrete paver block of M-35 grade with approved colour, design & pattern
300
-
756.15
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
24
-
3418.7
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
6
-
2298.55
White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap
30
-
1817.35
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
36
-
975.25
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.
24
-
254.8
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia
36
-
73.25
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm
36
-
752.8
Providing and fixing soil, waste and vent pipes : 100 mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
173
-
921.65
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 3989
18
-
384.9
Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS : 3989
54
-
334.95
Providing and fixing single equal plain junction of required degree : 100x100x100 mm Sand cast iron S&S as per IS - 3989
42
-
575.4
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 100 mm
252
-
309.95
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989
36
-
1034.45
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
36
-
137.85
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms
36
-
390.2
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 20 mm nominal outer dia Pipes
201
-
179.95
25 mm nominal outer dia .Pipes.
120
-
216.2
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes
307
-
191.65
40 mm nominal outer dia. Pipes.
120
-
321.15
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore
6
-
394.15
50 to 80 mm nominal bore
6
-
771.2
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore
24
-
428.2
20 mm nominal bore
24
-
396.55
40 mm nominal bore
12
-
584.7
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 15 mm nominal bore
6
-
243.6
Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore
36
-
67.8
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
12000
-
7.25
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
36
-
371.7
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore
36
-
475.7
Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 15 mm nominal bore, 105 mm long, weighing not less than 138 gms
24
-
165.3
Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :150 mm diameter
30
-
327.05
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe
30
-
479.85
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
18
-
1602.4
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
60
-
482.05
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
24
-
8634.1
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Circular shape 450 mm internal diameter
6
-
902.1
H D - 20 Circular shape 560 mm internal diameter
12
-
1300.95
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter
3
-
391.15
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
3
-
20681.55
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
120
-
384.5
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness
24
-
1003.95
Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).
12
-
4608.85
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
360
-
1034.65
Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
10
-
5583.8
Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part-4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall SS screws. The work shall be carried out as per specifications, drawing and as per directions of Engineer-in-Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles.
728
-
1452.9
Providing prefabricated sandwich panel- PUF Panel comprising to two sides facing of colour coated galvalume steel sheet and sandwiched between them CFC free close cell, high density rigid polyurethane foam (40 ± 2 kg/m3) having a thermal conductivity value of 0.023 w/mk and thickness 50mm. The outer & inner steel sheet of 0.50mm TCT steel 350 Mpa having a coating mass of 150 g/sqm zinc aluminium alloy coating total of both sides as per AS-1397 and finished with 20 microns colur coating of SMP polyester quality paint coat as per AS/NZS-2728:1997 (Category-3) over a 5 micron primer on exposed side and a back coat of 5 microns on inner side over a 5 micron primer. The panels should be of required length and required width with maximum width up to 1190mm with tongue & groove configuration with Camlock arrangement. The prefabricated panels shall be fixed directly to the girth using self drilling fasterners. The metal sheet confirm to IS: 513.AS-1397&2728. The polyurethane insulation shall confirm to IS: 12436 work shall be carried out as per direction of Engineer-in-charge.The rate of the item is inclusive of all materials, erection accessories, incidental charges, cost of dashfastners etc cost of making provision for doors, windows , ventilators. And concealed pipes, conduits and support for electrical and sanitary appliances. etc and other incidental charges as per sample.For payment finished puf sand witch panels shall be measured upto half centimetres for calculating area upto two places of decimal. No deduction shall be made for openings upto 0.10 sqm and no extra payment shall be made for wastages.For Roof panels with 50 (50/80) mm thick Roofing panels having finished with 0.50mm thich TCT Galvalume Hi-Rib sheet on outer side and 0.50 mm TCT Plain Galvalume sheet on inner side.
408
-
2698.05
For Wall panels with 80mm thick wall panels finished with 0.50mm thick TCT Galvalume Plain sheet with small ribs on both sides with Camlock arrangement.
1074
-
3063.3
Providing & fixing digital print graphics on wall with self-adhesive vinyl and lamination of 100 micron thickness of approved size, design including cost of preparation of sub-surface clean, smooth and suitable for pasting the graphics to the surface with low tack removable adhesives as per direction of Engineer-in- Charge.
3948
-
1126.5
Providing and fixing 18mm thick gang saw cut mirror polished for wall lining (vaneer work) including dado, skirting, risers of steps etc. in required design and pattern wherever required stone on 12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.30 kg / sqm including pointing with white cement slurry admixture with pigment of matching shade including rubbing curring, edge moulding, polishing etc. all complete as per direction of Engineer-in-Charge.
(a) 18mm thick granite of all colour
303
-
4601.1
Providing & fixing 100mm dia C.P. Brass grating of approved quality as per direction of Engineer in charge.
36
-
69.78
Providing and fixing stainless steel sliding door bolts with nuts and screws etc. complete : 250x16 mm
48
-
291.3
Providing and fixing stainless steel tower bolt with necessary screws etc. complete : 200x10 mm
78
-
85.1
Providing and fixing SS 304 grade (18 gauge sheet) signage board including printing of letters, borders, logo etc., with HP digital printing machine as per IRC:67-2001 on SS sheet with high quality white or any required shade and color as per direction of engineer in charge including making the required number of inles and putting the board on wall etc. in position with necessary screw batasha nail, wires ropes. etc. as per direction of Engineer in charge.
24
-
19130
Providing and Placing Registration Table of size 1830x400x750mm (wxdxh). Table made of CRCA steel 22 gauge duly powder coated. Modesty having dual color duly perforated. Table having provision of four equal fixed drawer unit on one side with telescopic chennel of Ebco make and other side one open shelve for keeping things. It is having provision of 8mm clear glass top all complete as per approval and direction of Engineer-in-charge.
12
-
20050.25
Providing and Placing Pharmacy Table of size 1525x400x750mm (wxdxh).Table made of CRCA steel 22 gauge duly powder coated. Modesty having dual color duly perforated. Table having provision of three equal horizontal drawers below the top. It is having provision of 8mm clear glass top all complete as per approval and direction of Engineer-in-charge.
12
-
15151.25
Providing and Placing open type storage unit of size- 1500x400x900mm (wxdxh) storage complete made 18mm thick commercial ply laminate with 0.70mm thick sunmica of required colour and design on both side duly edge banded with 2mm thick PVC edge lipping. Storage unit having 2 shelf making 3 compartments all complete as per approval and direction of Engineer-in-charge.
12
-
25875
Providing and Placing Overhead Unit of size 1270 x 400 X 455mm (WXDXH).Overhead body, shelf & shutter made up of 18mm thick commercial ply laminate with 0.70mm thick sunmica of required colour and design on both side duly edge banded with necessary hardware and fixture all complete as per approval and direction of Engineer-in-charge.
12
-
10693
Providing and Placing open type storage unit of size- 1500x400x750mm (wxdxh) storage complete made 18mm thick commercial ply laminate with 0.70mm thick sunmica of required colour and design on both side duly edge banded with 2mm thick PVC edge lipping. Storage unit having 2 shelf making 3 compartments all complete as per approval and direction of Engineer-in-charge.
12
-
21562
Providing and Placing fabric upholstered revolving Medium back chair of overall height 41" overall depth of seat 19" and overall width 19" seat & back made of 12mm molded ply with high density back and PU molded seat cushion, having PU arm rest with BAS seat & back and 5 pronged PP base with syncro tilt mechanism with movement of 2:1 ratio and fitted with rheumatic height adjustment.gas lift mechanism all complete as per approval and direction of Engineer-in-charge.
24
-
9586
Providing and Placing Doctor Table of size 1200x600x750mm (wxdxh). The top shall be made of 25mm thick commercial ply laminate with 0.70mm thick sunmica of required colour and design on both side duly edge banded with 2mm thick PVC edge lipping. The sides & modesty panel made of 18mm prelaminated particle board duly edge banded. Table having provision of three equal drawer unit on one side. It is having provision of 8mm clear glass top all complete as per approval and direction of Engineer-in-charge.
12
-
20314.75
Providing and Placing examination bed made of coated steel framework of 18 gauge with two section top, head rest adjustment made on ratchet system. Legs of 25mm MS round pipe of 18 gauge fitted with rubber shoes powder coated with mattress made of sponge and covered with leatherette dimension1800x600mm (wxd). Overall Size 1830x600x830mm (wxdxh) all complete as per approval and direction of Engineer-in-charge.
12
-
22489
Providing and Placing 3 seater bench having minimum length 2000mm, width of seat 450mm and having base made of die cast metal duly powder coated with levelers to adjust to floor level. The seats are made of perforated CRCA sheet duly counter bend to shape and powder coated of 40-50 micron with arms all complete as per approval and direction of Engineer-in-charge.
12
-
17744.5
Providing and Placing Executive Medium back revolving leatherette Chair with a dual layered foam for the seat & back The seat height can be adjusted to personalise the chairs with a gas lift that offers a cushioning effect. The backrest is specially contoured for comfortable seating. The one piece armrests are made of rounded smooth polyurethane which is resistant to climatic conditions. It is soft, yet firm to provide extra comfort. The wide base is five pronged for better stability and balance with castors made of first quality ABS material and resist weight upto 150 Kgs.seat is scientifically designed for reduction in fatigue by offering an optimal seat depth all complete as per approval and direction of Engineer-in-charge.
12
-
12385.5
Providing and Placing Ergonomically designed visitor leatherette chair with special contour on the back rest for human body with lumbar support which protects the spine and leaves the shoulder free for easy movement. Base of the chair made of ERW MS Round Pipe of 25 mm dia & frame not less than 14 gauge duly powder coated up to 40-45 microns. Seat and back made of 12 mm moulded ply. “U” foam is provided on seat & back with a bulge as per approved shape. “U” foam of density not less than 40 kg/m3. Armrest is made of one piece well rounded polypropylene all complete as per approval and direction of Engineer-in-charge.
72
-
8379.2
Providing and Placing Patient stool revolving Stool S.S Top, M..S. Tubular four legs fitted with PVC stumps, Foot ring supports, 18” to 27” adjustable height S.S top through screw, Pre-treated and Epoxy powder coated all complete as per approval and direction of Engineer-in-charge.
12
-
6052
Providing and Placing open type storage unit of size- 1400x400x750mm (wxdxh) storage complete made 18mm thick commercial ply laminate with 0.70mm thick sunmica of required colour and design on both side duly edge banded with 2mm thick PVC edge lipping. Storage unit having 2 shelf making 3 compartments all complete as per approval and direction of Engineer-in-charge.
12
-
20125
Providing and Placing Foot Step:Overall step size 460mmL x 230mmW.The first step height 230mm and second step size 450mm made of CRCA sheet.Frame made of 1"x18G CRC tubes fillted with PVC stumps. All frame work are pre-treated & epoxy powder coated of 40-45 micronall complete as per approval and direction of Engineer-in-charge.
12
-
4772.5
Providing and Placing Closed Type Steel Rack of size 84”x36”x15” (hxwxd) having 6 shelves making 5 compartments. shelves & sides made of mild steel sheet not less than 0.8mm. Slotted angle shall be 40x40x2mm. Shelves & angle shall be joint with galvanized hex. Nuts & bolts. Each rack shall be provided with rubber shoes at the bottom. All components are duly anti-rust treated and painted for long lasting finish all complete as per approval and direction of Engineer-in-charge.
12
-
21635
Providing and Placing Steel Almirah of size 1980x910x480mm (hxwxd) having 4 adjustable shelves making 5 compartments without locker Fabrication: Almirah’s side, back, top, bottom & shelves are made from mild steel of 22 gauge. The shelves shall have lipped flange 25mm width 15mm in depth. The shelves are fitted to rack strips made of mild steel sheets of 20 gauge thick with help of 4 brackets of 16 gauge that for support and adjustment and are having load bearing capacity of 60kg. uniformity divided load per shelf. The doors are made of mild steel sheet of 20 gauge and are having metal stiffener suitably spot welded to stiffen the door and fitted with the body with the help of but type hinges made of mild steel sheet of 18 gauge thickness double folded for free & smooth movement of doors all completed as per direction of Engineer in charge.
12
-
34469
Providing and Placing Almirah of size.1280x760x430 mm (hxwxd) having 2 adjustable shelves making 3 compartments without Fabrication : Almirah’s side, back, top, bottom & shelves are made from mild steel sheet not less than 22 gauge and without ant burrs & dents.The doors are made of mild steel sheet not less than 20 gauge and are having metal stiffener suitably spot welded to stiffen the door and fitted with the body with the help of but type hinges made of mild steel sheet not less than 18 gauge thickness double folded for free & smooth movement of doors. Steel shelving cabinet (Cabinet) is supplied duly fitted with 6 lever brass lock with duplicate keys of non corrodible metal. Steel shelving cabinet are finally finished by removing all dents, burrs & sharp edges and then immediately after pickling on mild steel parts is given phosphating treatment in dust free atmosphere before painting all complete as per approval and direction of Engineer-in-charge.
12
-
22711
Providing and Placing Screen three fold with curtain Overall Approx size: Middle span 1210mm Wide and sides span 610mm.MS tubular construction made of 19mm x 18G in three section .Legs made of 25mm x 18G fitted with 50mm dia castors. Supplied with hooks and spring with cutrain cloth. Finish pretreated and epoxy powder coated.
12
-
7100
Providing and fixing manually operated Roller Blinds of vista (Vista screen classic 5% with head rail) non back out series, Aerolox vista, marvle decor or mac make as per manufacture specification in required colour or shades with other connect accessories for fixing and smooth functioning of the blinds as per direction of Engineer-in-charge). Control Unit:- The control unit is made of high strength reinforced plastic. The clutch is of warp spring. High carbon steel springs are provided to transmit motion from driving to driven member of mechanism clutch. Clutch is operated directlonally by the use of endless beaded chain. clutch never need any adjustment. Idler :- Idler is of high strength reinforces plastic, consisting of a center shaft. The idler is mounted on the bracket by using a plastic. Roller Tube:- It is a 32 mm (OD) (depending upon the size) aluminium extruded grooved tube made of alloy T6063 weighing 0.27 Kg/m control unit and idler are fixed to the either ends of the tube. The fabric of the blind is fitted to the tube with heavy duty adhesive tape. Bottom rail:- It is an aluminium extruded rail with groove for fixing the fabric and powder coated in white. It is fixed to the bottom of the fabric in tension and straight. The end caps of the tube are ABS. The Size of rail shall be 21 mm (OD) made of alloy HE 9 WP weighing 0.27 kg/m all complete as per approval and direction of Engineer-in-charge.
120
-
1982.1
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
408
-
1037
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
1140
-
181
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
1020
-
324
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
1152
-
239
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
50
-
366
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way, Double door
12
-
1061
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/
Isolator) 8 way (4 + 24), Double door
12
-
3171
Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A
12
-
254
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A
12
-
678
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
360
-
173
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A
12
-
2242
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100 mmX75 mm)
84
-
185
6 Module (200 mmX75 mm)
36
-
258
8 Module (125 mmX125 mm)
48
-
297
12 Module (200 mmX150 mm)
24
-
344
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch
348
-
114
6 pin 15/16 A socket outlet
492
-
153
6 pin 25 amp socket
48
-
313
25 amp plug top
48
-
177
25 amp tiny trip MCB
48
-
200
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
48
-
24
Supplying and fixing extra down rod of 10 cm length G.I. pipe,15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)
144
-
22
Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
24
-
3672
Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.
180
-
134
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
120
-
23
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 35 sq. mm (32mm)
24
-
282
3 X 10 sq. mm (22mm)
24
-
171
Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
80
-
288
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
12
-
61
Supply & fixing of single phase 220 Volt, 1.0 HP mini seal priming comestic water motor pump set of size 25 x 25 mm, head range 6-32, discharge, range 2880-500 LPh i/c testing & commissioning etc complete as required. (Make:- Kirloskar )
12
-
5382
Supplying, installation, testing & commissioning of Street light LED fitting made of pressure die cast aluminum with LED source of 45-50 watt having following features: Luminous efficcacy 120 lm/watt, CCT = 3000K, CRI70, Surge protection device = 5KV, Secondary optics with lens, IP 66 housing, electronic driver, on the existing street light pole with tower wagon etc as per specification given in terms and conditions etc. complete as required.
50
-
2898
Supplying installation testing and commissioning of IP65 Surface mounted Led bulkhead type fitting 10-12watt in 5000-6000 K CCT including mounting on surface with help of MS clamps etc including connections ,earthing etc as reqd.
25
-
677
Supplying, installation, testing & Commissioning of surface/recess type 34W to 36W Full window glarefree opal Diffuser LED Panel of size 600X600mm suitable for Armstrong/POP/GB ceiling with MS Powder coated White Housing. Total system Lumen of 34W to 36W LED should be 3400 or above in Cool day Light(5600K to 6500K), Power factor0.95, CRI (Ra) 80, LED Lamp Efficacy130 Lm/W. Complete with all accessories as required with connections etc. complete as reqd.
240
-
2587
Supplying Installation, testing and commissioning of 1200 mm sweep ceiling fan with copper binding including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, complete etc. as required.
84
-
1832
Supplying, Installation, Testing and Commissioning of following size Heavy Duty Exhaust Fan of 300 mm sweep 900 RPM Single Phase, in the existing opening i/c louver shutter making good the damage, connection, testing, commissioning etc. as required.
24
-
3551
Supplying & fixing of Double Door Storey PVC stand for inverter having locking arrangement & wheels for moving etc as reqd.
12
-
2061
Providing and fixing fan hook made from 25 x 5 mm thick MS flat in existing girder with suitable size nut-bolt with washer etc complete as reqd.
84
-
234
Supplying and laying of one number PVC insulated and PVC sheathed aluminium conductor XLPE armoured power cable of 1.1 KV grade of following size in following way etc as required. 3 x 10 sqmm (On surface)
36
-
199
3.5 x 35 sqmm (On surface)
300
-
371
3.5 x 35 sqmm (in the existing RCC/HUME/METAL/HDPE pipe)
24
-
364
Supplying, laying & fixing of 3 core x 2.5 sqmm copper flexible control cable in existing pipe i/c connections, interconnections etc as reqd.
432
-
200
SITC of 1.5 TR window type AC unit BEE- 5 Star (2018 (ISEER (W/W) 3.30) with rated cooling capacity not less than 4950 watts, ,low sound with remote control suitable for operation on 230 V, 50 Hz, single phase AC supply complete i/c accessories, fixing on existing window with wooden frame, plywood, minor civil work at site etc as reqd.
48
-
36065
Supplying and fixing of 4 KVA voltage stabilizer with TDR suitable for input 145-280 V & output 195-245V, three step with high voltage Trip & MCB on surface complete with connections testing & commissioning etc. as reqd.
48
-
4466
Providing and fixing 4.5 Kgs. Capacity carbon dioxide type fire extingushier consisting of brand new high pressure steel cylinder and having the approval of controller of explosives, Nagpur, wheel type valve, internal discharge tube, one meter long high pressure discharge hose, non-conduction horn, suspension breckets, fully charged fixed with brass screws/dash fastner including making good the walls wherever required.
12
-
6721
Providing and fixing of dry powder (stored pressure) 6 Kgs. Capacity ABC type fire extinguisher bearing ISI mark complete filled with mono ammonium phosphate based dry powder and fitted with discharge pipe and pressure gauge complete fixed suspension breackets with brass screws/dash fastener including making good the walls wherever required.
12
-
2239
Supplying, installation, testing, & commissioning of 4 star inverter type single door 190-230 ltr. Refregerator with base drawer and working on single phase 100-240 V AC supply 50 Hz i/c working connection, testing & commissioning etc complete as reqd.
12
-
18793
Supply & fixing of 1600 VA Inverter (UPS type) with suitable battery No of with minimum 30 mint. Backup time with 36 months warranty of battery i/c making connection, testing & commissioning etc complete as reqd.
12
-
34802
Supplying, installation, testing & commissioning of 32" LED, Smart HD TV including company supplied bracket on wall remote & DTH setup box with disk and wire and including activation of viewer card of 3 month complete etc as reqd.
12
-
26594
Supplying, installation, testing & commissioning of floor mounted water dispenser having capacit;y of 3.2 ltrs. With 16 Ltrs storage cabinet and 20 liter water botle duly filled with drinking water at all locations in Delhi of Aam Aadmi Mohalla Clinics etc complete as required.
12
-
9550
Supplying and fixing of 32 mm dia X 2.00 meter long G.I. pipe(medium class) bracket for mounting of fluorescent / HPMV /HPSV street light fitting on pole including bending the pipe to the required shape, 2 Nos. 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required
48
-
733
Add CPWD Cost Index @21.46% (On DSR Items)
1
-
3175196
Deduct PWD Cost Index @9.5% (On DSR Items)
1
-
1707252
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements