Netaji Subhas Institute Of Technology Tender

74 SITC of Condenser gooseneck microphone (cardioid) for Podium with minimum Specification /Features i.e. Frequency response: 50 - 19,000 Hz or better, black, length 500 mm (20") or better, LED ring, 3-pin XLR male, programmable button, phantom power driven, support RFI shielding alongwith Shock Mount etc. complete with installation as per the site requirement.

7 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

53 SITC of 12U Floor Mount Network Rack with accessories (Make:- Rittal / APW / Emerson )

72 Supply, installation, testing and commissioning of High Voltage Relay array, Should have 8 channels of power switching or more, with Built-in/External 8 voltage-driven isolated digital inputs, or provide an external digital input port. Should Support for 120 to 240 Volt 50/60 Hz lighting and motor loads, Should support Per Channel 10 Amps incandescent, 5 Amps fluorescent, 0.5 HP at 120 to 240 Volts AC, 50/60 Hz; 5 Amps at 30 Volts DC; 16 Amps Resistive or more, Total Module should support 80 Amps incandescent, 40 Amps fluorescent at 120 to 240 Volts AC, 50/60 Hz or more. Should be capable of communicating with central control system.

80.4 For 4th Year

12 Providing and Fixing Wood slatted panel perforated panels of width 128-192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade . The boards shall have a special perforation pattern where the reverse surface has a fluted perforation with consecutive 2-3mm wide groove followed by 13_14 mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece hot pressed to achieve NRC of 0.6. and Humidity Resistance (RH) of 70% .The panels shall be mounted on special aluminium splines (keel) using inside clips provided by Manufacturer and approved by the Architect/ Engineer-in-Charge. The panel shall be mounted by tongue and groove mechanism using inside clip on GI extruded keel . The supply shall be backed by a Manufacturing Test Certificate . The panel to be fixed over the existing GI framework payable in item 4. Install Keel vertically using screws and plugs at spacing of not more than 600mm centre-to-centre. Trim the tongue of the first bottom panel and install using headless nail with groove side upward. Subsequent panels are installed with tongue side downward by engaging with each other using tongue and groove mechanism and secured by inside clip. Continue this process until required height is achieved. Shorter butt edges need to be joined using industrial/wood glue. Finish off the edges using wooden moulding of matching colour all complete. Installation should be carried out as per Manufacturer recommended procedure. The work to be done complete as per drawings and specifications, and directions of Engineer in charge.

33.2 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

68 SITC of 50 feet HDMI cables with installation as per site requirement.

36.2 6 Module

32 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

62.2 For 2nd Year

55 5 Years 24x7 Onsite Comprehensive Warranty and Support for 24 Port Non-PoE Managed Access Switch as per specifications provided and installed under this contract as required. 55.1 For 1st Year

78 SITC of Standard AV Rack of size 12U to keep the equipments with necessary power points.

41 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

SH-02 (DISTRIBUTION BOARD & MCB) 37 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 37.1 4 way (4 + 12), Double door

35 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 35.1 5/6 A switch

23 Supplying and placing following classroom desk cum bench of following specifications. Product Specification A) Legs:-Legs are made of MS ERW tube section (IS:7138) of size 75 X 25 X 2 mm thick oval tube with 5 mm thick HR brackets as per IS:2062 and 2mm thick CRCA brackets as per IS:513 welded on to the tubes. Assembly is powder coated with epoxy polyester. -Leg height varies from 705 to 1005 in pitch of 50 as per layout.-Sturdy anchoring by anchor bolts on to base of 8mm thick plate for proper resting of Leg.-Shoe made of ultramid - Nylon are provided at the bottom for covering the base plate. B) Side clads:- Side clads made of 18 mm thick plate with 0.8mm thick pvc lipping and on the outside covered with welded metal structure made of 2 mm thick CRCA as per IS:513 powder coated with Epoxy polyester . C) Worktop:-Worktop are made of 25 mm thick Pre-Laminated Board of E1-P2 Grade and approved shade conforming to IS:12823. All the edge of work surface are provided with machine pressed 2mm thick pvc edge band glued with hot melt glue. D) Seat: -Seat has self closing mechanism which will operate by means of dead weight . Seat understructure is made from combination of welded fabricated structure of 5mm Thk HR as per IS:2062 and 8mm thk ply as per IS:303 with moulded PU foam of density 55 kg/cu.mtr. on top which in turn is covered with stitched upholstery. Seat assembly is covered on bottom side by means of seat cover made of CRCA (IS:513). E) Seat Back:-Seat back is made from combination of 8mm thk ply as per IS:303 with foam on top which in turn is covered with stitched upholstery. F) Seat Support Frame :-Seat support frame is made from combination of MS ERW tube section (IS:7138) of size 80 X 40 X 2.5 mm thick rectangular tube and MS ERW tube section(IS:7138) of size 48 X 19.1 X 2 mm thick oval tube welded together . Assembly is powder coated with Epoxy polyester. CAP made of ultramid are provided from front to cover the oval tubes. G) Modesty:-Modesty is made of 25mm thick pre-laminated twin board of E1-P2 Grade and approved shade conforming to IS:12823. All the edge of modesty are provided with machine pressed 2 mm thick pvc edge band glue with hot melt glue etc. All complete as per direction of Engineer-in-charge.

64 SITC of Wall Mount with Pan & Tilt option angle +- 30 degree easily mountable on any concrete surface & should have the capacity to hold 35 K.G Weight with all complete as per the site requirement

18 Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building

81.2 For 2nd Year

36.3 8 Module

SH-03 LIGHT / FAN FIXTURES) 40 Dismantling the existing worn out / defective fittings from the ceiling and SITC of minimum 36 watt Aluminium slim energy efficient LED Panel light fitting having system efficacy minimum 100 lumen/watt LM79, color temp 6500 deg K, recess mounting suitable for fitting in the 600mm x 600mm square existing space having symmetric glare free illumination in the false ceiling complete with all standard accessories including drivers etc. complete as required

15 Providing and fixing sun screen manual chain operated roller blinds consisting of 100% Polyester fabric, fabric thickness 0.50 mm fabric weight = 270 gsm +- 5 %, fabric width 230 cms, tearing strength 4.5 kgf warp, bursting strength 34 kgf, colour fastness to light 5 to 6 grade in position of standard quantity and approved shade/colour including necessary accessories MS clamps. screws and drilling etc. as required all complete as per direction of Engineer-In Charge. (Approved make : Vista/MAC/DECO/NOVA)

62.5 For 5th Year

B Electrical Work SH-01 (WIRING AND ACCESSORIES) 28 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 28.1 Group C

71 SITC of ten button wall mountable control panel with minimum Specifications /Features i.e. programmable 10 button keypad, a volume knob, and built in control processor with min 2x bidirectional RS232, 1x IR, 2x Relay, Ethernet port to control devices over Ethernet. Support local power supply and can be powered over Ethernet, shall be supplied with PoE injector or PoE network switch etc. all with installation as per site requirement.

38.2 Double pole

75 SITC of Audio digital Signal processor Unit with minimum specification / features i.e. USB Audio Interface, Minimum 8Input Processing Unit with AEC Enable, Input Channel: Minimum 6 or more, 3 x Line Output or more, Frequency Response : 20 Hz to 20 kHz, THD: 0.1% or better, SNR : 90dB or better, Channel Separation/Crosstalk : -75dB or better, USB audio interface for soft codec application, Digital Network Link Port for future expansion, IP / RS232 port for third-party control, with complete installation as per site requirement.

82 Dismantling & Buy Back of old & defective following items from NSUT as per required. (Contractor / Agency should be ensure that disposal of the old / defective wastage material should be disposed off through the authorized recycler registered under Delhi Pollution Central Board / Central Pollution Control Board. Contractor/ Agency should also submit 'Certificate of Destruction'). 82.1 Light Fitting

81 Providing services for operation of the AV systems, in 4 no. Smart Classrooms at NSUT West Campus Jaffarpur with operators (technical) from 6 AM to 7 PM, six days a week. (1 no. operator from 6 AM to 2 PM and 1 no. operator from 11 AM to 7 PM. The timing can be changed as per the requirement of department or direction of engineer in charge.) Job is not limited to operation of AV only, it also include the following work: 1. Operators will unlock the rooms daily at 6:00 AM & lock the room at 7:00 PM daily. 2. Operators will prepare the class/ lecture hall ready by putting the system on & ready for use by the teachers and students as the case may be. 3. Job also includes taking up any issues/query of installed IT related query for LAN switch, Wi-Fi, internet etc. 4. Job also includes the cleaning the surface of display & Wacom touch monitor. 5. Job also includes to interchange any faulty AV unit with the stand by units provided by NSUT. 6. Job also includes to keep all AV equipments up & running, regular maintenance, software/firmware upgrade etc. 81.1 For 1st Year

SH:- 06: FIRE ALARM SYSTEM 57 Supplying, installation, testing & commissioning of smoke detector with built in LED and mounting base complete with all connections etc. as required.

69 SITC of 6 feet HDMI cables with installation as per site requirement.

30 Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 Amps modular socket outlet and 15/16 Amps modular switch , connection etc. as required .

50 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 50.1 1 or 2 Module

29 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. 29.1 Group C

SH-04 (Earthing & Raceway) 42 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

3 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete

44 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

55.2 For 2nd Year

58 Supplying, installation, testing & commissioning of addressable manual call point complete as required.

25 Providing and placing of modular workstations system of size 900mm (W) X 450mm (D) x 750 GRIHA compliant having following specifications. The product should be complete and as per approved sample and as per the direction of Engineer-In-charge. Main Panels Construction (Front and End panel of each cluster) - Main Partition panel having 4 horizontal blocks and consists of Vertical extrusions2Nos and Horizontal extrusions 5 nos made of 1.2mm thick aluminium with duly powder coated at every division of tile/block. Each panel shall have Bottom frame fabricated for 52.4mm panel comprises of 2 nos. L-channels made of 2mm thick CRCA (Cold Rolled, Cold Aneeled) steel (IS: 513), formed plates of 3mm thick Hot Rolled steel (IS: 2062) & ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of provided with 2Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs Construction- Legs are fabricated by CO2 welded MS Tube of section 38mm x 25mm x 16 swg (IS: 7138) with the base plate of the Hot Rolled MS plate of 35x22x5mm (IS: 2062) over which an M8Leveller is fitted which allows for adjustment of the height by 50mm. It will be coated with 45- epoxy powder coating. The Bottom Frame is bolted with the Upright verticals. Each Panel is 50micron thickness of epoxy powder coating. Each Panel consists of 2Nos Intermediate blocks. Intermediate Blocks- In a 52.4mm Thick panel intermediate block shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate on both sides. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables, if required as per the instructions of Engineer-in-charge. These blocks will be located in the middle bands of the panels made out of a composite construction of MDF and paper honeycomb. ------ •Top Block:- Each Panel consists of glass top block with film of approved color. This block shall be made of 4mm thick clear toughned glass tiles fitted onto both the sides of the end pannel using horizontal and vertical stiffeners made of 0.6mm thick powder coated CRCA steel (Grade-D IS:513).• Intermediate Blocks: Laminate finish blocks shall be made from 18mm thick particle board of superior quality, cladded with laminate of approved shade. • Bottom Blocks Metal finish blocks shall be made from two components of 0.8mm thick M.S. CRCA Grade D as per IS: 513 powder coated with epoxy polyester finish. Aluminium Trims for End Pannel : The top trims and end trims for 22.8mm partition shall be made from aluminum extrusion having material AL96063- T6. Top trim in 22.8mm thick panel shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66. Wooden Worktop: Supplying and Fixing of Workstation Worktop as per the approved shape and site requirement made out of 25mm thick prelaminated particle board of superior quality All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worktop is fitted to the panels by work surface brackets. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513-19. Brackets are slided in between end trim and vertical extrusions. The product should be complete and as per approved sample and as per the direction of Engineer- In-charge.

33.3 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

54 SITC of 24 Port Non-PoE Managed Access Switch as per specifications, as per direction of engineer in charge.

81.4 For 4th Year

73 SITC of 8-Port Ethernet Switch etc. complete with installation as per site requirement.

77 Supply, installation, testing and commissioning of min 8 Inch, 2-Way In-Ceiling Speaker. Support Power Handling upto 200 Watts program at 8 Ohms, Having minimum Woofer 8 inch, Tweeter minimum 0.97 inch dome. Transformer Taps min 7.5W/15W/30W/60W at 70V/100V, Frequency Response 80 Hz to 16 kHz (±3 dB), Sensitivity 91.5 dB @ 1W/1m, Should comply to CE, UL.

37.2 6 way (4 + 18), Double door

9 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class deodar wood

55.3 For 3rd Year

SH:- 07: AV SYSTEM 63 SITC of Minimum 85” diagonal display, Resolution - 3840x2160, Brightness 500 nits with 2xHDMI IN port, 1 VGA Port, 1 Display port, inbuilt OPS Slot, able to support 4K content with all complete as per the site requirement

6 Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only

37.3 8 way (4 + 24), Double door

80 Comprehensive maintenance including repair/replacement of damaged item/part/system with all accessories, spare parts, software, hardware and other related equipments as required for smooth functioning of Audio Video system covered under item no. 63 to 79. 80.1 For 1st Year (During defect liability period)

59 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

81.3 For 3rd Year

34 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel conduit as required ( For computer power in Furniture ) 34.1 3 x 4 sqmm

45 Supply and installing following size of under floor GI (hot dip galvanized) raceways made out of 1.6mm thick sheet steel, standard length 2.5 meters, 1/2/3 compartment complete with jointing sleeves and other accessories under floor installation including cutting and chasing the floor, making good the same, placing in position and cleaning from inside complete of following sizes etc. as required.(50mm x 38mm x 1.6mm)

79 Supplying and laying all type of cables for healthy functioning of above system in one smart classroom i.e. shielded twisted pair cable, HDMI patch cord, USB cable, audio cable, speaker cable 2 core 1.5 sqmm PVC insulated shielded cable all completed as per the directions of Engineer-in-charge.

60 Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 60.1 4 Zone

76 Supply, installation, testing and commissioning of 2 channel Class D technology Amplifier. Should be minimum 150 W per channel, and configurable for LoZ, Hi-Z operation. Should be able to configure as 1 channel bridged operation up to 300 W. Should have frequency response of 20 Hz to 20 kHz ±0.5 dB at 1 W, S/N Ratio : 103 dBA, 20 Hz to 20 kHz, balanced, Should have protection at each output under fault conditions (Over Current, DC Offset, high Temperature, Under Voltage etc), Should comply to CE, UL, FCC. (Additional BIS to be shared if applicable)

33.4 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

80.3 For 3rd Year

80.5 For 5th Year

31 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

35.2 3 pin 5/6 A socket outlet

65 SITC of Digital Podium with minimum Specification /Features i.e. in Metallic Frame and wooden top, powder coated with caster wheels & brakes. Drawer for keyboard, mouse and document camera. Provision of 19" Rack inside podium to fit in international standard equipment. Access doors for servicing both from front and back side of the podium. Interactive Display: Interactive Panel Size of 21.5" Diagonal, Full HD Panel, Touch Technology: (Electromagnetic + Capacitive) Touch Digitizer and supplied with Electromagnetic Stylus. Provision for gooseneck microphone and button control panel, connectivity Ports HDMI, VGA, audio, Network, USB etc. complete with installation as per the site requirement.

55.5 For 5th Year

SH-05 (Networking) 47 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface / recessed steel / PVC Conduit as required. 1 Run of Cable (Make:- Commscope Systimax Only)

19 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to IS : 1328 BWR type

2 Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

20 Supplying and Placing in position Faculty Table of following Specifications. Overall Dimension of the Main Desk Shall be - 1500mm x 600mm The system shall be a desk-based system with a platform understructure made up of a combination of MS. Tubes and plates. Understructure - The slanted legs are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Acrylic (8 mm thick Acrylic both side frosted) or of Metal 1.2 mm thick CRCA. Worktop - Worktop shall be made of 25MM thick Pre-Laminated Board conforming to IS: 12823. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches shall be on the wire, tray/channel A wire management, it shall be a part of the understruture and can be in the form of enclosed metal tray or 2 level enclosed channel to provide points on the tray. Pedestal having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer Unit consists of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit :Welded Assembled of 0.8mm thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2mm thick CRCA Top Stiffene, Bottom stiffener, Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8mm thick Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). The product should be complete and as per approved sample and as per the direction of Engineer-In-charge. .

27 Providing and fixing 25mm dia and 900mm long drushed steel finish pull handles with lond bolt and cap for fixing from outside as oer design approved all complete as per the direction of engineer -in-charge.

52 Providing and fixing Stranded Low smoke Halogen Cordage Unshielded Cat 6 Modular Patch cord of length 2 mtr with plug insertion life not less than 750 times and minimum Plug Retention force of 133N i/c making connections etc. complete as required.

39 Supplying and fixing following rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required 39.1 TPN MCB 63 A

5 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

81.5 For 5th Year

43 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

38.3 Triple pole and neutral

51 Providing and fixing Stranded Low smoke Halogen Cordage Unshielded Cat 6 Modular Patch cord of length 1 mtr with plug insertion life not less than 750 times and minimum Plug Retention force of 133N i/c making connections etc. complete as required.

67 SITC of 4K Portable Document Camera with minimum Specification /Features i.e. 13 MP CMOS Sensor, minimum 30x Zoom with HDMI In & HDMI Out, USB Output, Inbuilt Storage of minimum 100 images, inbuilt microphone for audio video recording, Image rotation 0° / 90° / 180° / 270° / Flip / Mirror, CE, FCC and RoHS Certified etc. complete with installation as per site requirement.

10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

66 Supplying & fixing of Intel PC consist 512 GB SSD 16 GB Ram ,I7 processor intel nuc, Wife and lan Antivirus 5year Windows 11 alongwith wireless keyboard and mouse i/c SITC as per direction of E.I.C.

14 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc complete : Kiln seasoned and chemically treated hollock wood 50 x 20 mm

62.4 For 4th Year

4 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

82.2 Ceiling Fans

36 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 36.1 3 Module

8 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square

80.2 For 2nd Year

49 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 49.1 RJ 45 Information Outlet

17 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

21 Supply and placing of chair having cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric.* Full Back Size : 45.5 cm. (W) x 53.0 cm. (H) *Seat Size :48.5 cm. (W) x 47.0 cm. (D)The HR polyurethane foam used in seat and back cushion is moulded in Density 45±2 kg/m3, and hardness load 16 ± 2 kgf as per 15:7888 for 25% compression. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes The "5" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-am)de form the back-spine structure involved in multidimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm The pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos. in wheel castors.. The pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. 5 nos. twin wheel castors are injection moulded in Poly-amide having 5.0±0.1cm heel diameter and assembled to the pedestal.

22 Supplying and placing Visitor Chair of following Specifications. Overall Dimensions of Chair-Seat Height - 46.5cm.Height - 93.5cm Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hotpressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Copolymer Polypropylene. TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. The product should be complete and as per approved sample and as per the direction of Engineer-In-charge.

56 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 25MM PVC Conduit

55.4 For 4th Year

34.2 6 x 4 sq. Mm

70 SITC of 4K/60 HDMI matrix switcher with six HDMI® inputs and two HDMI outputs, 6x2 matrix switching. Having video support HDMI Deep Color, 3D, & 4K, Having audio format support for Dolby® TrueHD, DTS-HD®, and uncompressed 7.1 linear PCM audio, Should support HDCP & EDID management, Should be controllable via Ethernet, Should be CE, UL & RoHS compliant.

62.3 For 3rd Year

48 Providing and fixing 24 port loaded Straight patch panel of height 1U in the existing data end rack including making connections, channel labelling etc. complete as required.

11 Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

62 Comprehensive maintenance including repair/replacement of damaged item/part/system with all accessories, spare parts and other related equipments as required for smooth functioning of Fire Alarm system covered under item no. 57 to 61. 62.1 For 1st Year (During defect liability period)

A Civil Work 1 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

33 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 33.1 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

46 Supplying and fixing of UPVC trunking of size 100 x 50 along with accessories on surface complete as required.

38 Supplying and fixing 5 amps to 32 amps, rating, 240/415 volts, 'C' Curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 38.1 Single Pole

26 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 2.50 sqm).

61 Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following intems duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc. complete as required. 10 Zone panel for fire alarm system. 250 Watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as required - 2 Nos. ( one to act as standby). Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24V DC supply conforming to IEC-268 for simplex mode of operation/ communication suitable for20 Nos. talk back unit - 1 Set. Announcement control desk suitable for selection of different zones selectively and ON ALL CALL switch with visual indication etc. complete as required - 1 Set. Amplifier change over switch for inter changing amplifier - 1 No. Monitor panel for loudspeaker complete with output selector, ON/OFF switch, fuse, visual indication etc. complete as required -1 No. Gooseneck microphone with stand and ON/OFF switch -1 No. Main ON/OFF switch, fuse indication lamps, DC and AC voltmeters & ammeters, terminal blocks etc. complete as required - 1 Set. Battery charger trickle cum boost to take complete load of fire alarm & PA system complete will all accessories including providing & fixing of 2 Nos. 12 Volt, 60 AH each sealed maintenance free batteries - 1 Set.