National Institute Of Fashion Technology Tender

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks).

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing & fixing false ceiling at all height including providing & 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. fixing of framework made of special section, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I channels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs Made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm.

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing &Fixing Door closer , 60Kg.

Providing & Fixing wooden work station( including keyboard tray, cable manager, foot rest, Locks, Handels, soft board on vertical side etc complete in all respect, as per the attached drawing) with 19mm commercial board sun mica finish and painting, polishing, hardware etc complete in all respect and as per direction of engineer-in-charge

Providing & fixing bright brass sliding door bolt 250X10mm

Providing & fixing of 10mm thick bison Board.

Providing & fixing of curtain wall with 10mm antilo glass toughened with Aluminum framing, work should be complete in all respect.

Supplying and fixing Single pole 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. As required.

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2x1.5 sq mm + 1x1.5 sq mm earth wire

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2x2.5 sq mm + 1x2.5 sq mm earth wire

Supplying and fixing suitable size PVC box with modular plate and cover in front on surface or in recess, including and fixing 5 pin 5/6 & 15/16 amps, modular socket outlet and 15/16 amps modular switch, connection etc as required.

Supplying and fixing suitable size PVC box with modular plate and cover in front on surface or in recess, including and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc as required.

Wiring for Light/ power plug with 2x4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduits along with 1 no. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

supplying and drawing following sizes FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 1x1.5 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm dia

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm dia

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mm x 75 mm)

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in recess etc. as required. 3 Module (100 mm x 75 mm)

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in recesss etc. as required. 6 Module (200 mm x 75 mm)

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in recess etc. as required. 12 Module (200 mm x 150 mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 3 pin 5/6 socket outlet

Supply and Installation of Wall Mounting Bracket Fan 400 mm Sweep Single Phase, AC 230 V, 50 hz with all accessories etc.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface / recessed steel / PVC conduit as required.

Preliminary, Testing & Ferruling of UTP cables, fixing of Face Plates & I/Os, Cat 6 Cable Termination at i/O, Fixing of Jack Panels, Cat 6 Cable Termination at Jack Panes, Labeling at Rack end & work area, Dressing of cat -6 wire in Data rack etc. as required.

Supplying and drawing 2 pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface / recessed steel / PVC conduit as required.

Providing and installation of recessed LED panel light (600*600mm), including choke etc all complete. This including extension of wires from existing point in ceiling as per the new light all complete.

Providing and installation of 10 watt led down lighter including driver/ choke etc all complete including making new connection with extension from old lines etc all complete.

Supplying and fixing 32 A rating, 240/415 V, 10 KA "C" curve, miniature circuit breaker (DP MCB) for inductive load with box complete with connections, testing and commissioning etc

Supplying and installation of Telephone sockets including embedded box, cover plate etc (modular) all complete

Information outlet (I/O) CAT 6A with Gang Box and Phase Plate (Make: D-link or equivalent)

Supply and installation of  Split Air Conditioner Nominal cooling capacity in 2.0  Ton / (kcal/hr): 2 Ton / 6000 kcal/hr ( a) Coil Material: 100% Copper Coil  b )   Compressor: ROTARY BEE Star Rating: Minimum :  3 )  ( Make : Hitachi / Daikin / Voltas / Carrier ) 

Providing and fixing of power cable between indoor to outdoor unit of split ac  as per requirement ( 3 core x 2.5 mm)  

Providing and fixing refrigerant copper piping with tubular insulation  suitable for 2.0Tn Split AC 

MS Stand for the outdoor unit ( Floor / Wall mounted type )  

SITC of PVC drain pipe 25 mm dia with necessary fittings and clamps as per requirement