Municipal Corporation Tender

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.10:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

6.1.2:Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

6.4.2:Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:6 (1 cement : 6 coarse sand)

4.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts

4.2.3:Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

10.25.2:Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13.45.1:Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

16.64:Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in- Charge.

16.68:Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

7.32.1:Stone work plain in Copings,Cornices, String courses and plinth courses, upto 75mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.Red sand stone

110.10:Providing and fiving name board made of MS Sheet 90x60cm, 1mm thick with frame of MS angle 50x50x6mm, two diagonal braces at the back of the sheet of MS flat 40x6mm, total height of the board above ground level 2.40m, length of legs below ground 0.30m embedded in CC block 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) 30x30x45cm including excavation and removal of surplus earth with in 50m lead, applying priming coat of approved steel primer, painting with synthetic enamel paint of approved quality and lettering with enamel paint of approved colour (one side) as per drawing/direction of Engineer-in-Charge

110.17:Providing and Placing of precast RCC benches (chair bench with back Rest) using Cement Concrete grade M-30 consisting of 2 No. L-Shaped base support of thickness 100 mm having Back height 1000mm, front height 450mm and Base width 620mm having 5 No. of RCC planks 1500x100x50 mm and one number plank of size 1500x200x50mm in the approved colour and shade; The minimum weight of MS Reinforcement bar in the base support will be 3.4 Kg having 4 Nos. 8 mm dia M.S. Bar distributed along the section and periphery of the legs with sufficient No of 4 mm dia MS stirrups. Each base support will have 3 Nos. 12mm dia (2 Nos. 40mm and one number 65 mm long) galvanised coupling nuts welded suitably to the main reinforcement at appropriate locations so as to receive bolts for fixing of seats of concrete planks on base support and 3 holes to received carriage bolts for fixing back rest planks. The minimum weight of MS reinforcement bar in the plank of 200 mm wide will be 4.4kg and of 100mm wide 2.9 kg. All the RCC Planks will have 2 holes of 14mm dia at appropriate location, so as to receive 12mm dia galvanized bolts for foxing on the base support. One of the planks of size 1500x100x50 mm shall be engraved in the centre at the back with letter SDMC or as directed by Engineer in Charge, 2 planks of size 1500x100x50mm and 1 plank of size 1500x200x50mm will be bolted to coupling nuts provided inthe base support of both sides with 2 number of 12mm dia and 65mm long galvanized steel CSK bolts and one Eva Washer for each bolt to form a seat; 3 planks of size 1500x100x50mm will be bolted to coupling nuts provided in both the base support to form back rest with 6 Nos. (Two Nos. in each plank) half threaded carriage bolts and nuts of size 165m long and 8mm dia with Eva and steel washers. The holes visible at the back side of the bench will be sealed with cement mortar after assembling. Side edges of all the planks shall be painted with acrylic bases paint of approved colour and shade and front portion of seating and back rest planks shall be polished to give glossy finish complete as per direction of Engineer-in-charge.

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

15.60:Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved