Municipal Corporation Tender

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Fine dressing the ground

Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and then rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly, as per direction of officer in charge

Providing and stacking of Ficus panda of height 45-60 cm. with 6-7 branches and healthy foliage in p.bag of size 25 cm as per direction of the officer-in-charge.

Providing and Displaying Ficus black vivion piller topiary (cylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Ficus Long Island topiary well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Ficus Nuda topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Ficus Retusa topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus reginold piller type Topiary well developed with fresh & healthy 210 to 240 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Golden Bottle brush Topiary well developed with fresh & healthy foliage 5 to 6 big ball 115 to 180 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Topiary of Ficus Bush King well developed with fresh & healthy foliage from Top to Bottom with single piller 60 to 75 cm spread, 210 to 225 cm ht., in 35 cm Cement Tray/Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Casuarina fresh & healthy having 5 to 6 specific shape and size ball well developed 195 to 210 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and fixing of precast RCC chair bench with arm rest each bench consists of 2 no. L-shaped base support in grey cement color (thickness 80mmx90mm, 890 mm back height; 450 mm front height with base width 690 mm) and 1 no. reinforced concrete plank in red color of size 1500 mm x 400 mm x 50 mm total height of the bench 890 mm manufactured using cement concrete 1:1.5:3 (1cement 1.5 coarse sand: 3 stone aggregate 12.5 mm nominal size) using vibro compaction process reinforced suitable to promote long use and to prevent damage during handling. Transportation &erection, all parts are joined together with galvanised nuts and bolts of suitable size and all bolts are sealed after assembly, bench top and back planks are treated with special anti-corrosive water proof coating so as to make surface glossy and water proof and as per direction of Officer-in-Charge. Size: Length 1500 mm Back Height 890 mm Base support 690 mm Front height 450 mm Seat – 2 Nos. Planks of size 1500 mm x 400 mm x 50 mm And 1 No. Planks of size 1500 mm x 425 mm x 50 mm Total length of support & arm – 2.75m in/c curved portion x-sectional area = 0.08 x 0.09 = 0.0072 sqm.Total length in/c curves Qty of RCC = 2 x 0.0072 x 2.75m = 0.0396 cum

SQUARE DECK WITH CANOPY 5’: 3 NOS. Main Pillar Pipes Made Up Of 80 Mm NB "B" Class G.I. Pipes. Height : 1.5 MTR From GL SQUARE DECK WITH CANOPY 3’: 1 NOS. Main Pillar Pipes Made Up Of 80 Mm NB "B" Class G.I. Pipes. Height : 1.0 MTR From GL SWINGING BRIDGE : 1 NOS. 60mm NB G.I. Pipe Used For Main Structure. 1.3Mtr W X 3.0 Mtr Lx1.5 Mtr Ht WAVE SLIDE(1.5 M) : 1 NOS. Wave Slides Made Up Of Fiber Reinforce Plastic Material . 3.0 Mtr Length X 0.5 Mtr Width SPIRAL SLIDE(1.5 M) : 1 NOS. Spiral Slide Made Up Of Fibre Reinforced Plastic Material Height : 2.1 Mtr And 4.0 Mm Thick STEPLADDER : 1 NOS. Step Ladder Molded With Fibre Reinforced Material. 0.4 Mtr L X1.0Mtr W X1.0 Mtr HT ROCK CLIMBER : 1 NOS. Rock Climber Made Up Of Fibre Reinforced Plastic Material. Length 1.8 Mtr And Width 1.0 Mtr BRIDGE : 1 NOS. Plain Bridge Made Up Of Fiber Reinforce Plastic Material. 2.4X1.0X0.15Mtr (Lxwxh). NET CLIMBER : 1 NOS. Main Pillar Pipes Made Up Of 32 Mm NB "B" Class G.I. Pipes. 1.5 Mtr Ht . SLIDE ENTRY : 1 NOS. Slides Entry Made Up Of Fiber Reinforce Plastic Material . 0.9Mtr X0.25Mtr X 0.9Mtr(Lxwxht) Structure Build With CO2 Welding Process With Controlled Parameters. Fiber Reinforce Plastic Mouldings With Resin, Color Pigment CSM Mat. Powder Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

TODDLER SWING.THE AREA :- 2.8M X 1.0M . In This Toddler Swing The Center Support Shall Be Made Up Of 80 Mm NB B Class G.I. Pipe. The Horizontal Bars Shall Be Made Up Of 50 Mm NB B Class G.I. Pipe. All GI Pipes Shall Be Powder Coated. Between The Two Horizontal Bars There Shall Be A Heavy-Duty Metal Clamp Attached To It. The Bucket Seats Of The Toddler Swing Shall Be Made Of Rubber With Anti Skid. The Ball Bearings Shall Be Mounted Inside Specially Designed Nylon Balls. The Rubber Seat Shall Be Affixed On 8 Mm Thick GI Chain. The Seats Shall Be Made With Full Care So That The Child Does Not Fall From It While Swinging. Powder Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

STD. SEE SAWHANDLE :-20 MM N B PIPE. LEVER-32 MM N B PIPE. COLMUN : 60 MM N B PIPE. BEARING : NYLON BUSH PRESS FITTED. SEATS: FRP SEATS WITH STEEL FRAME. THE TOPCOAT IS DULY POWDER COATED. The Level Of See Saw Shall Be Made From 15, 20 And 25mm NB B Class GI Pipe. The Seat Of See Saw Shall Be Made From FRP/LLDPE. The Stand And Bush Bearing Made In 40mm NB B Class GI Pipe. See Saw Lever Shall Be Welded To 5mm Thickness MS Plate For Nut Bolting With Stand. All Pipes Flat Shall Be Powder Coated To Avoid Rusting. Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

ARCH SWING. LEG SUPPORT : 80 MM NB PIPE, SEAT- ANTI SKID RUBBER BELT. BEARING : HEAVY DUTY BALL BEARING. AREA : 3.0 M X 2.5 M. HEIGHT : 2.5 M. TOP BAR : 60 MM NB PIPE. SUSPENSION : 6 MM RUBBER COATED CHAIN. THE TOPCOAT IS DULY POWDER COATED. In This One Child Can Enjoy The Swing At One Time. The Arch Shaped Side Frame Shall Be Made Of 80mm NB B Class GI Pipe Shall Be Made Up Of 50mm NB B Class GI Pipe. The Frame Shall Be Powder Coated To Give An Aesthetic Look. The Swing Shall Be Made Up Of 10mm Thick Anti Skid Rubber Top The Rubber Belt Seat Shall Be Suspended On 6mm Rubber Coated GI Chairn. The Bail Bearings Shall Be Mounted Inside A Specially Designed Nylon Clamp. Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

Supply and fixing of sign boards of 0.91 x 0.61m size with support length of 3000 mm. Manufacturing, supplying and fixing of Retro reflective sign boards made of 2 mm thick aluminum sheet face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type – IV of ASTM-D 4956-01 in green and silver white including subject matter, message (bilingual(, symbol and borders etc as per IRC: 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 And fixing the same with suitable sized aluminum alloy rivets @ 20 cm c/c to back support frame of m.s angle iron of size 35x35x5 mm and m.s flat of 25x5 mm along with theft resistant measures, mounted and fixed with 2 nos. clamp of mls flats of size 25x5 mm to a vertical post of 3 mtr height made up of msl pipe of 60 mm n.b welded with two hold fast of m.s angle 25x25x3mm of 30cm length each at bottom and including making holes in pipes, angles, providing & fixing m.s message plate of required size, steel work to be paired with two or more coats of synthetic enamel paint of required shade and of approved brand and manufacture over a priming coat of zinc chromate yellow primer (vertical post to be painted in black/white/grey color) Backside of aluminum sheet to be painted with two or more coats of epoxy paint over an appropriate priming coast including all leads and lifts etc. complete as per drawing, specification and direction of Officer-in Charge

SEATED PULLER /PULL CHAIR made from “C” Class G.I pipe. DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE AREA:- 1.2Mtr x 3Mtr. Seated puller equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made from “C” Class G.I. pipe. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. The seat frame is of 32NB “C” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nuts & bolts are used for assembly.Thecirclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

CROSS TRAINER /ELLIPTICAL EXERCISER DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height). SAFE AREA: - 1.77 x 1.2Mtr. Cross trainer equipment made from “C” Class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame Pipes are of 80NB “C” Class G.I. Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of DIA 250 mm & 10mm thick. The Handle Frame is made up of 25NB “C” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD With 5 mm thickness. The footrests are made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright .The Bearings used are of “6007 2RS1” “62052RS1” and “62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). A16 , A 24 mm circlips are used for assembly. Bolt M8X16 mm and NY lock nut of M8 made of SS304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

BACK EXTENSION DIMENSIONS: - 1400mm (Length) x 700mm (Width) x 820mm (Height). SAFE AREA: - 2.4Mtr x 1.7Mtr. Back Extension Equipment made from “C” class G.I. Pipe of different NB pipe. (NB stands for Nominal Bore i.e. Internal Diameter of pipe in mm) The main frame is of 50mm NB made from “c” Class G.I. pipe. The Foot resting frame of 32mm NB made from ”c” Class G.I. pipe. The handle frame is of 25NB made from “C” Class G.I. pipe. The seat fitted on the outer frames is made up o f M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The foundation used for fixing is consists of 50mm NB made from ”C” Class G.I. pipe.The footrests are made from Injection Moulded Plastic LLDPE / HDPE. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

STANDING SEATING TWISTER. DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height). SAFE AREA: - 3 Mtr x 1Mtr. Seating & Standing Twister equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. The M.S. round plate of DIA 250 mm & 10mm thickness is welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “C” class G.I. pipe. The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “C” class G.I. pipe of 25mm NB.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate fitted on the bottom frame is made up of Injection Moulded Plastic LLDPE / HDPE and supported by M.S. Round Plate of size 300mm diameter&10mm thickness. Closing Caps are made up Injection Moulded Plastic LLDPE / HDPE. The Pins used are made up of DIA 35 mm SAE 8620 bright material. The bearings used are of “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SKY WALKER DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height). SAFE AREA: - 2.7Mtr x 1.6Mtr. Sky Walker Equipment made from “C” class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame pipe is of 80mm NB made from “C” Class G.I. Material which is bend at the radius of 250mm.The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle The handle frame is of 25mm NB made from “C” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. The footrests made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. The bearings used are “62052RS1” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

CHEST PRESS . DIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2200mm. (Height). SAFE AREA: - 3.0Mtr x 1.7Mtr. Chest press equipment made up of “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The bottom welded with support of M.S. round plate of DIA 250 mm & 10mm thickness. The connecting pipes are made up from 25NB “C” class G.I. pipe. The handle frame is made up from 32NB “C” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings used are of “62052RS1” &“62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cer clips used for locking is made up of A24 mm & A16mm. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

ROWER (DIMENSIONS: - 1200mm (Length) x 1000mm (Width) x 920mm. (Height). SAFE AREA: - 1.5Mtr. x 1.5Mtr. Rower Equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in mili-meters.The Main frame is of 80NB “C” class G.I. Pipe welded with M.S. round plate of 250mmX10mm. The handle frame 25NB is made from “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To join the movement frame to main frame connecting links made up from 32 NB G.I. “C” class pipe. The seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed tools and dies to have uniform radius of 20 mm with no sharp edges. Pins used of Diameter 17mm are made up from SAE 8620 bright material. The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The P.U. bushes (Stopper) used to avoid the collision. The cir clips used for assembly is of A 16. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1 cement : 2 coarse sand : 4 stone agg. 20mm nominal size)

TAICHI SPINNER ( DIMENSIONS: - 700mm (Length) x 1000mm (Width) x 1280mm (Height). Safe Area:- 1.9Mtr X 1.9Mtr Taichi spinner Equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The handle movement round frame is made up from 25 NB “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB“C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25 mm of SAE8620 bright material. The bearing used is “62012RS1” & “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile S.S. nut bolts are used for assembly. Foundation cover Closing Cap is made of Injection Moulded Plastic LLDPE / HDPE. The cer clips used for assembly is of A24 and A11.The nylon bush is used for handle knob. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

SHOULDER BUILDER Providing and fixing Shoulder Builder made from C- Class GI pipe. The Center Pipe is of 100mm NB made from “C” Class GI pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of 25 NB & 20 NB made from “C” Class GI pipe. To Join the centre pipe & handle movement frame seamless pipe of 130mm dia& 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” class GI Pipe, M.S. Round Plate of 250 mm dia& 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm dia bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly is of 25 mm diameter. The Poly Urethin plastic bush is used for handling. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)