Municipal Corporation Tender

6.1.2:Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

16.69:Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

2.27:Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

16.91.1:Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

6.4.1:Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

10.25.2:Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

7.12.1.1:Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade: One face dressedRed sand stone

13.72:Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 ( 1 cement : 4 coarse sand), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 kg of cement per square metre, top layer 15 mm cement plaster 1:1/2:2 ( 1 cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately).

1.1.1_20:Disposal of materials by mechanical transport including loading ,unloading and stacking lime ,moorum, building rubbish for lead 20 km

110.17:Providing and Placing of precast RCC benches (chair bench with back Rest) using Cement Concrete grade M-30 consisting of 2 No. L-Shaped base support of thickness 100 mm having Back height 1000mm, front height 450mm and Base width 620mm having 5 No. of RCC planks 1500x100x50 mm and one number plank of size 1500x200x50mm in the approved colour and shade; The minimum weight of MS Reinforcement bar in the base support will be 3.4 Kg having 4 Nos. 8 mm dia M.S. Bar distributed along the section and periphery of the legs with sufficient No of 4 mm dia MS stirrups. Each base support will have 3 Nos. 12mm dia (2 Nos. 40mm and one number 65 mm long) galvanised coupling nuts welded suitably to the main reinforcement at appropriate locations so as to receive bolts for fixing of seats of concrete planks on base support and 3 holes to received carriage bolts for fixing back rest planks. The minimum weight of MS reinforcement bar in the plank of 200 mm wide will be 4.4kg and of 100mm wide 2.9 kg. All the RCC Planks will have 2 holes of 14mm dia at appropriate location, so as to receive 12mm dia galvanized bolts for foxing on the base support. One of the planks of size 1500x100x50 mm shall be engraved in the centre at the back with letter SDMC or as directed by Engineer in Charge, 2 planks of size 1500x100x50mm and 1 plank of size 1500x200x50mm will be bolted to coupling nuts provided inthe base support of both sides with 2 number of 12mm dia and 65mm long galvanized steel CSK bolts and one Eva Washer for each bolt to form a seat; 3 planks of size 1500x100x50mm will be bolted to coupling nuts provided in both the base support to form back rest with 6 Nos. (Two Nos. in each plank) half threaded carriage bolts and nuts of size 165m long and 8mm dia with Eva and steel washers. The holes visible at the back side of the bench will be sealed with cement mortar after assembling. Side edges of all the planks shall be painted with acrylic bases paint of approved colour and shade and front portion of seating and back rest planks shall be polished to give glossy finish complete as per direction of Engineer-in-charge.