Irrigation And Flood Control Department Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 manufactured sand : 8 recycled aggregate 40mm nominal size)

Brick work with C & D Recycled products concrete brick of class designation M-10 in foundation plinth in cement mortar 1:4 (1 cement : 4 Manufacture sand) C&D Recycled Products.

Half Brick masonry with C & D Recycled products concrete brick of class designation M-10 in foundation plinth in cement mortar 1:4 (1 cement : 4 Manufacture sand) C&D Recycled Products.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete:40 mm thick with 20 mm nominal size stone aggregate.

12mm cement plaster finished with a floating coat of neat cement of mix1:4 (1cement : 4 fine sand).

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Supply & filling of C&D recycled products recycled aggregate 40mm size including loading, unloading, banking the same and filling up /ground depressions, with all leads and lifts.

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate /retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. Note : Excess/less constructed then specified in this item is payable/recoverable seperately M-10 grade plain cement concrete ( cement content considered @ 220 kg /cum).

Providing and laying RMC of M-30 grade by using minimum 400 kg of cement (43 grade, OPC) as per cum of concrete in roads/streets manufactured in automatic RMC plant using coarse sand and graded stone aggregate of 20mm nominal size in appropriate proportion as per approved design criteria including transportation to sit in transit mixer, including cost of admixture in recommended proportion as per IS9103 to accelerate/retard setting of concrete to improve workasbility with out impairing strength and durability as per specification including pumping spreading and compacting mechanically by using needle and surface vibrators, leveling to required slope & camber, finishing by floating & brooming with wire brushes etc. and curing complete, as per direction of Engineer-in-charge. Note:- Cement content considered in M-30 is @ 400 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately M-30 RMC by using minimum cement @400 kg/cum. Cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer.

Providing and fixing red sand slab 40mm thick over drain.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :Foundations, footings, bases of columns, etc. for mass concrete

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality HD-20 Circular shape 560 mm internal diameter