Irrigation And Flood Control Department Tender

Supply of earth including royality, excavation and carriage of earth by mechincal transport including loading, unloading and banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor II level in all shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.8.9.1.2 Granite of any colour and shade

Providing and fixing of CHEST PRESS SINGLE make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM SEATED CHEST PRESS of size 1500x550x1825mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Handgrip to be made from high quality rubber. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of FOREARM TWIRL (Small Two wheels) make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM FOREARM TWIRL/TAI CHI SPINNERS TAI CHI SPINNERS of size 1150x1150x1650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. The circular spinners made from 32mm dia hot dipped galvanized steel rods and welded on to the post using a 6mm dia hot dipped galvanized steel supports. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury. Bearing used shall be made maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. on ground with concrete of minimum strength M-25 and J shaped The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of SHOULDER TWIRL SINGLE make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM BIG SHOULDER WHEEL of size 857x850x1815mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of ABS BOARD (Single) make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM ABS Board of size 1400x1366x650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-100 micron thick. All joints of pipe are4 robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Sit up boards and Base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm, colourful and UV resistant and environmental friendly. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete us set, fix the equipment on to it and cover nuts and bolts with technical specifications. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineerin- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and Installation of PULL UP STATION of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Providing, designing and fixing of pull up station, The total frame is made with main post of 114mm dia And 4 mm thick G.I. Pipe as per IS-1239with help of connecting links. It is a combination of two exercises. Pull up section has handle made up of 25 NB G.I. pipes. PVC handgrips are provided at both ends of handle. Back section has hand rest of rectangular pipes. Small 25 NB G.I. pipes are provided for back rest. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps if required for user safety against entrapment. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of OVATE STEPPER make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM Ovate stepper of size 1148x585x1486mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and Installation of SURF BOARD Double of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Surf board in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 4 mm thick G.I. Pipe as per IS-1239 and rest of the pipe 40mm dia and 4 mm thick G.I. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm colorful and UV resistant and environmental friendly or FRP Material of same specification, Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE/ FRP caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc

Providing and Installation of LEG LIFT POST of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Surf board in pair of size 1050 x 800 x 1150mm fabricated with main post of 114mm dia and 4 mm thick G.I. Pipe as per IS-1239 and 6 no of spacer pipes made by 25 NB G.I. pipes are arranged parallel at equidistance to form a back rest of product. The paired handle pipe consists of 25NB galvanized pipe fixed at the top and bottom of 80NB support pipe main frame. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc.

Providing & Installation of SKY WALKER of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Providing, designing and fixing double cross walker of size 1600 x 600 x 1600 mm fabricated with main post of 114mm dia and 4 mm thick G.I. Pipe as per IS-1239 and rest of the pipe 40mm dia and 4 mm G.I. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 8mm colorful and UV resistant and environmental friendly or FRP Material of same specification, Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE/ FRP caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc.

Providing and Fixing of 200 watt LED Flood Light(P66) With aluminium housing and heavy heat sink,including toughned glass(Surya)

Supplying, installation, Testing and commissioning of continuously tapered multifaceted and polygonal cross section 16mtr high mast system hot dip(galvanized) with wind velocity as per IS 875 part-3 as per detailed specification attached with following Make Bajaj, Philips, G.E., Volmont. a) 2 sections having suitable sectional length with slip joints between various sections without any circumpherial welding. b) Double drum winch with separate handle for manual operation of winch with a torgue limiting device for safe checking of carriage. c) Raising/lowering type lantern carriage designed to carry 9 Nos. luminaries control gear box, junction box and top pulley assembly with weather proof cover. d) Necessary suitable length for lowering and raising of lantern carriage of stainless steel wire ropes of 7/19 construction and with suitable size of multi core flexible copper power cable. e) Hinged service door in base section base plate earthing terminal. f) Lightening conductor final made of 25mm dia 300mm long G.I. tube having single prong. g) Integral single power tool (electrical) for lowering & raising of high mast.

Providing and laying the RCC foundation suitable for erection of 16mtr high mast as per manufacturers recommendation including excavation, casting of foundation anchor plate, templates and foundation bolt manufacturer from special steel along with nuts, washers etc. R.C.C. work 1:1.5:3 (1 cement” 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) with material, labour and reinforcement with size of footing 2.10x2.10x0.20m laid over 1:4:8(1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size) and foundation pedestal of size 0.90x0.90x2.00m or as per approved drawing complete as required.

Providing and fixing precast reinforced cement concrete bench of over all size 1500 mm x 450 mm x 1000 mm, the bench consist of 02 nos. L-shape base sport in cement, thickness 100 mm back height 1000 mm front height 450 mm base width 620 mm as per sketch and 05 nos. reinforced concrete planks in red colour of sized 1500 mm x 100 mm x 50 mm and 01 nos. RCC planks of size 1500 mm x 200 mm x 50 mm by using M-30 grade of concrete using vibro compaction process, bench top and back planks are treated with special anti-corrosive water proof coating so as to make surface glossy and water proof including transportation, erection all part are jointed to gather with galvanized nuts and bolts of suitable size. All bolts are sealed after assembly.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage