Irrigation And Flood Control Department Tender

Supply of earth inclduding royality,excavation and carriage of earth by mechanical transport lead upto 5 KM , breaking clods, watering, and rolling each layer with 1/2 tone roller wooden and steel rammers and dressing in embankments for roads , flood banks, marginal banks and guide banks or filling up ground depression with all lead & lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor II level in all shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

Centering and shuttering including strutting, propping etc. and removal of form for all heights Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor II level, excluding the cost of centering, shuttering and finishing :4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 85.95

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). cum 5012.65

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. sqm 615.70

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.8.9.1.2 Granite of any colour and shade sqm 2018.00

Providing and fixing of CHEST PRESS SINGLE make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM SEATED CHEST PRESS of size 1500x550x1825mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Handgrip to be made from high quality rubber. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of FOREARM TWIRL (Small Two wheels) make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM FOREARM TWIRL/TAI CHI SPINNERS TAI CHI SPINNERS of size 1150x1150x1650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. The circular spinners made from 32mm dia hot dipped galvanized steel rods and welded on to the post using a 6mm dia hot dipped galvanized steel supports. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury. Bearing used shall be made maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. on ground with concrete of minimum strength M-25 and J shaped The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of SHOULDER TWIRL SINGLE make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM BIG SHOULDER WHEEL of size 857x850x1815mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of ABS BOARD (Single) make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM ABS Board of size 1400x1366x650mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-100 micron thick. All joints of pipe are4 robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Sit up boards and Base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm, colourful and UV resistant and environmental friendly. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete us set, fix the equipment on to it and cover nuts and bolts with technical specifications. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineerin- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and Installation of PULL UP STATION of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Providing, designing and fixing of pull up station, The total frame is made with main post of 114mm dia And 4 mm thick G.I. Pipe as per IS-1239with help of connecting links. It is a combination of two exercises. Pull up section has handle made up of 25 NB G.I. pipes. PVC handgrips are provided at both ends of handle. Back section has hand rest of rectangular pipes. Small 25 NB G.I. pipes are provided for back rest. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps if required for user safety against entrapment. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and fixing of OVATE STEPPER make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM Ovate stepper of size 1148x585x1486mm fabricated with main post of 114mm and 4.00mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLPDE manufactured by rotational moulding with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLPDE caps for user friendly. The equipment to be fixed on ground with concrete of strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc.

Providing and Installation of SURF BOARD Double of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Surf board in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 4 mm thick G.I. Pipe as per IS-1239 and rest of the pipe 40mm dia and 4 mm thick G.I. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic of 8mm colorful and UV resistant and environmental friendly or FRP Material of same specification, Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE/ FRP caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc

Providing and Installation of LEG LIFT POST of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Surf board in pair of size 1050 x 800 x 1150mm fabricated with main post of 114mm dia and 4 mm thick G.I. Pipe as per IS-1239 and 6 no of spacer pipes made by 25 NB G.I. pipes are arranged parallel at equidistance to form a back rest of product. The paired handle pipe consists of 25NB galvanized pipe fixed at the top and bottom of 80NB support pipe main frame. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc.

Providing & Installation of SKY WALKER of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/GRAND SLAM. Providing, designing and fixing double cross walker of size 1600 x 600 x 1600 mm fabricated with main post of 114mm dia and 4 mm thick G.I. Pipe as per IS-1239 and rest of the pipe 40mm dia and 4 mm G.I. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 8mm colorful and UV resistant and environmental friendly or FRP Material of same specification, Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE/ FRP caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:2:4) block of size:- 60x60x60cm after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc.

Providing and fixing precast reinforced cement concrete bench of over all size 1500 mm x 450 mm x 1000 mm, the bench consist of 02 nos. L-shape base sport in cement, thickness 100 mm back height 1000 mm front height 450 mm base width 620 mm as per sketch and 05 nos. reinforced concrete planks in red colour of sized 1500 mm x 100 mm x 50 mm and 01 nos. RCC planks of size 1500 mm x 200 mm x 50 mm by using M-30 grade of concrete using vibro compaction process, bench top and back planks are treated with special anti-corrosive water proof coating so as to make surface glossy and water proof including transportation, erection all part are jointed to gather with galvanized nuts and bolts of suitable size. All bolts are sealed after assembly.

Providing and fixing Victorians type of Garden bench both side of arm of Garden bench made of flora cast iron and having of back height of minimum 700 mm seating height of 375 mm (approx) and both side of garden bench is connected with M.S tube of 65 x 25 mm sheet angular tube having 15-20mm in 12 Nos. for seating purpose with extra support 25 x 5 mm . M.S flat for stability all sharp and rough edges of benches are to be grinded with grinder and all fillup with MS seal where is it required necessary. This bench having the provision of hold fast system of for growing bench complete with a cutting of 1st class quality paint. finally bench is assembled with nuts and bolts including all tax. The length of bench be 1500mm and minimum overall weight is not less than 90KGS.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). kg 472.40

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-incharge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).Overhead informatory road signage.

Supply of building rubbish/malba/similar unserviceable material dismantled or waste material by mechanical transport including royalty loading unloading banking the same in layers not exceeding 20cm in depth, breaking clods watering rolling each layer with 1/2 tonne roller or wooden or steel rammers and upto embankments for roads, flood banks, marginal banks and guide or filling up ground depression, with all leads & all lifts.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.16.70.2 Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

Supplying, installation, Testing and commissioning of continuously tapered multifaceted and polygonal cross section 16mtr high mast system hot dip(galvanized) with wind velocity as per IS 875 part-3 as per detailed specification attached with following Make Bajaj, Philips, G.E., Volmont. a) 2 sections having suitable sectional length with slip joints between various sections without any circumpherial welding. b) Double drum winch with separate handle for manual operation of winch with a torgue limiting device for safe checking of carriage. c) Raising/lowering type lantern carriage designed to carry 9 Nos. luminaries control gear box, junction box and top pulley assembly with weather proof cover. d) Necessary suitable length for lowering and raising of lantern carriage of stainless steel wire ropes of 7/19 construction and with suitable size of multi core flexible copper power cable. e) Hinged service door in base section base plate earthing terminal. f) Lightening conductor final made of 25mm dia 300mm long G.I. tube having single prong. g) Integral single power tool (electrical) for lowering & raising of high mast.

Providing and laying the RCC foundation suitable for erection of 16mtr high mast as per manufacturers recommendation including excavation, casting of foundation anchor plate, templates and foundation bolt manufacturer from special steel along with nuts, washers etc. R.C.C. work 1:1.5:3 (1 cement” 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) with material, labour and reinforcement with size of footing 2.10x2.10x0.20m laid over 1:4:8(1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size) and foundation pedestal of size 0.90x0.90x2.00m or as per approved drawing complete as required.

Supplying and laying double walled corrugated (DWC) High Density Poly ethylene (HDPE) pipe of 50/38 size having corrugation on the outer wall and plain surface on inner wall confirming to IS 14930 (Part II) below the ground level excluding excavation refilling the trench etc. as per specification etc. as required

Providing and fixing of 200 watt LED flood light (IP66) with aluminium housing and heavy heat sink, including toughned glass (Surya).

Supplying, installation, testing and commissioning of feeder pillar of suitable size made from 2mm thick CRCA sheet dust and varmin proof duly phosphatized and painted inclusive of suitable size 4 strip Bus bar complete with inter connection, inter earthing and providing and fixing below noted accessories.(M/R) Timer 24 hours = 1 No. TPN MCCB – 63 Amp = 1 No. MCB- 6 to 32 Amp = 10 Nos. Power contactor = 1 No. Indicator light = 3 Nos. Reverse switch = 1 No.

Supplying of PVC insulated and PVC sheathed (General purpose) XLPE/armored multi core cable with standard aluminum conductor suitable for working voltage upto and including 1100 volts confirming to IS 7098/Part/1988 with amendment slips upto date. Size 4x25sqmm. (M/R)

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of size not exceeding 35sq. mm clamped with 1mm thick saddle on wall surface, as required.

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of size direct in ground including excavation and refilling the trench etc. as required but excluding sand cushioning and protective covering upto 35mm.(7.3.1)

Earthing with G.I. earth pipe 4.5 mtr long, 40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.5.2

Supplying and laying 6 SWG G.I. wire at 0.50metre below ground level for conductor earth electrode including connection, termination with G.I. thimble etc. as required. 5.7