Irrigation And Flood Control Department Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

PPGI Puff Panel material used for developing of porta cabin: Material Details for Puff Panel Office (i) Bottom fixing with coated mm thick “C” channel flashing 50x50x50mm with 8mm fastener. (ii)50mm thick powder-coated(PPGI) sandwich puff panel for side wall . (iii) 50x80mm thick powder-coated(PPGI) sandwich puff panel for roof. (iv).Corner panels(inner & outer) covered with PPGI 0.5mm thick powder coated flashing 50x50mm. (V) Roof Corner flashing outer covered with 0.5mm thick ”C” channel flashing 75x75mm. (vi) Cam-lock for holding/joint puff panel sheets covered with PVC lock and cap.(vii)Silicon for fixing joints between every puff panel sheet. (viii)Pop-ripit for fixing flashing with puff panels. (ix) ”L” shape corner outer column flashing 10x100mm. (x)30mmthick puff panel door with patam /chokhat flashing. (xi)Door lock, SS handle,4” SS Kabze. (Xii)Aluminum powder coated sliding windows with aluminum safety grill(4’x3’). (xiii) Electric open fitting with ISO mark wires of 4mm,2.5mm,1.5mm and 0.75mm (xiv)ISO mark switch & socket, LED tube light, mcb and bulket light(outer). (xv)500x500mm vitrified tiles on the carpet area of porta cabin. (xvi) Labour charges fo installation/fixing job of puff panel, tiles and electric work. (xvii)Switch, socket, tubelight and MCB for porta cabin and 02no. separate MCB for spilt AC. (xviii)Separate toilet with WC, washbasin, Urinal and water tap(Size:8'x 4’). (xix) Separate Kitchen with sink , water tap and storage(Size:8'x 4’). (xx) Spilt A.C.1.50 Ton. Transportation Charge included.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of Engineer-in-Charge. With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqm. Mm F.R. L.S. PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with piano type switch, phenolic laminated sheet suitable size ;M.S. box and earthing the point with 1.5 sq.mm FR L.S. PVC insulated copper conductor single core cable as required (Group C).

Wiring for circuit/sub main wiring along with earth wire with the following sizes of FR L.S. PVC insulated copper conductor, single core cable in surface/recessed steel conduit as required. a) 2x2.5 sq.mm + 1x2.5 sq. mm earth wire.

Providing & fixing 36 Watt 2x2 Ceiling light (Make approved brand) or as per aprroved by Engineer-in-Charge.

Supplying in position Plastic Chair, Brand-Avro,Anmol,Nilkamal,Godrej, Maharaja Chairs or as directed by Engineer-in-Charge, Dimensions (In Centimeters)- 60D x 58.5W x 90H, (approx) Weight-4.00 KG (Approx),Assembly-No Assembly required, Primary Material-Plastic, Room Type-Office,Outdoor and indoor, Maximum weight recommendation-200.00 Kg ,Country Of Origin-India with 3 years warranty.

Supplying in position Plastic Table, Brand-Avro,Anmol,Nilkamal,Godrej, Maharaja Chairs or as directed by Engineer-in-Charge Dimensions (In Centimeters) W x H x D: 121.9 cm x 72.9 cm x 72.9 cm (3 ft 11 in x 2 ft 4 in x 2 ft 4 in) Country Of Origin-India with 3 years warranty.

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II ofASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment) Overhead informatory road signage.